Search Documents

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By James W. Neill

Bituminous coal has for many years been used for the smelting of iron-ores in the blast-furnace. In some districts in Scotland it is used alone, in others it is used mixed with coke. The similar use of certain bituminous coals in the United States has been repeatedly mentioned in the Transactions. (See, for instance, as to the Hocking Valley coal, the papers of Dr. T. Sterry Hunt, Trans., ii., 275, and vii., 313; and as to Indiana "block-coal," the paper of Mr. J. S. Alexander, Trans., i., 225.) Phillips (Elements of Metallurgy, p. 250) says: " Raw coal for blast-furnace use must be of a non-cokiog kind, and, when of suitable quality, is perhaps the most advantageous fuel." In the first

Jan 1, 1892

Coal Mining machinery has undergone enormous changes in design and complexity of controls in the past 10 years. Specialised, high productivity equipment has been manufactured in Australia, in sufficient volume, to satisfy the local mullet needs.Local manufacturers face greater challenges from overseas competition, as well as increased customer demands to improve machine performance, productivity, quality, reliability and safety. In order to meet these demands now and in the future, it will be necessary to review work practises, and restructure production and quality systems to incorporate the latest principles and philosophies.

Jan 1, 1991

By Maribeth Amyot

This paper assesses the current status of computing education in ABET-accredited mining engineering programs in the United States. The hardware and software being used are reviewed. The extent to which computer applications are incorporated into mining engineering courses is also surveyed. Today's capabilities and practices are compared with those of the past to establish, trends in computing education. The concerns of mining educators regarding computers are addressed, as are views on the direction in which mining engineering programs appear to be heading in preparing students to meet the computing needs of industry.

Jan 1, 1985

By M. R. TECK, N. Rudd, L. K. Thomas, D. L. Katz

The authors are to be congratulated for presenting the first comprehensive paper on the theory and practice of threshold pressure determination in connection with underground gas storage. It is of particular value since most previous experimental work on this subject has been proprietary to the commercial laboratories engaged in such testing and to their clients. This dlscussion is presented in amplification of the subject paper, not in criticism, and is based upon our experience with approximately 5,000 threshold pressure determinations. Our comments are directed primarily to the experimental procedures as described by Thomas et al. It should be noted that, while clay mineral-rich lithologies are the most common caprock materials, the samples used (Table 1) include low permeability sandstones and carbonates, but do not include shales or other formations in which clav minerals exert a dominant effect. While our experience on samples analogous to those investigated by the authors generally confirms their findings, we have found that even more rigorous experimental conditions must be imposed where clay minerals are the controlling factor. These additional conditions result from the well-known molecular character of the clay minerals themselves in which water is interlaminated with, and bonded to, silicate sheets, thus becoming an essential component of the molecule. In many clay minerals the character of the intersheet bonding, and thus the dimension of the lattice, is strongly affected by variations in the identity and concentration of cations present in the intersilicate water. On a supermolecular scale, adsorbed water films on particle or "flakes" of shale provide much of the cohesive force necessary to maintain mechanical strength. The thickness of these films is variable and inversely proportional to intergranular pressure within the dimensional limits involved in caprock investigation. The thickness of the intersilicate water layers may also be subject to pressure under some conditions. These considerations are reflected in several necessary modifications of the experimental procedures described by the authors. Two of these are, in our judgment and experience, of such importance that they cast real doubt on the validity of data obtained on argillaceous materials without their application. The very careful resaturation procedures proposed by the authors should give good results in connection with the relatively "inert" lithologies used in their experiments. Our experience suggests, however, that they would create more problems than they would eliminate if applied to argillaceous materials. 1. Drying of the sample at the temperature and for the duration indicated by the authors not only will dessicate the sample with consequent shrinkage cracking, parting along bedding planes, and even total disassociation in the case of fissile shales, but it may also alter the character of the clay minerals themselves — in some cases irreversibly. 2. Prolonged evacuation to 2 microns Hg further dessicates the sample and is even more effective in reducing the intersilicate water content. 3. Resaturation with water differing in pH or chemical content from that existing originally in the sample also serves to alter the nature of the sample, particularly its structure and strength. 4. Our experience has been that, even with the thorough precautions proposed by the authors, complete resaturation of very fine grained materials is rarely obtained. Yet our experience confirms the

Jan 1, 1969

By D. S. Bloswick

An investigation an4 analysis of slip/fall accidents specifically pertaining to underground coal mines was conducted. From a population of 751 accident reports, three major sources of injury which account for over 80% of the incidents have been identified. The specifics of this study are presented in this paper. Based on the results, several recommendations are made to reduce such accidents in underground mines. In addition, a brief discussion of the slip-hazard analysis laboratory at the University of Utah, which will be useful in future analyses of these accidents is presented. Work in this facility includes the simulation of certain mining activities in a controlled setting. Foot forces are measured and work methods subsequently developed to minimize the slip potential of these activities.

Jan 1, 1988

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

By H. E. Stauss, E. I. Salkovitz, F. W. von Batchelder

EXISTING information regarding the structure of a spherulite in nodular cast iron is based on optical studies. According to these data, a nodule consists of an aggregate of graphite crystallites radiating from the center, with the closely packed basal planes at right angles to the radii. The c axes lie along the radii. This view faces some uncertainty in the fact that the c axis does not represent the accepted direction of fastest growth in graphite. To supplement the optical information, X-ray studies have now been made. The principle used was to screen the nodule in greater part from the X-ray beam and expose only a minor cap. As successively larger portions of the nodule were introduced into the X-ray beam, any differences in the X-ray patterns could be observed. Such photographs have been taken with chromium radiation and a Laue camera. The graphite nodule itself, about 0.010 to 0.025 in. in diam, was mounted with vaseline on a micrometer screw for control of the linear motion. The nodule rotated about 45" each time that it was translated linearly. The nodules were obtained from magnesium-treated hypereutectic iron by electrolytic solution of the iron in hydrochloric acid. In Fig. la is shown the pattern of the thinnest cap examined. In Fig. lb is shown the pattern of the same nodule moved 0.003 in. farther into the X-ray beam, and rotated 45" at the same time. Figs, la and lb indicate incomplete circles for graphite (the two outer circles arise from graphite) with the side arcs much weaker than the top and bottom ones. The arcs obtained are themselves not continuous in intensity but vary with maxima of intensity some 15" and 30" apart. The structure of the nodule that would give rise to such a pattern can be explained as follows. Basically the nodule consisted of small crystallites. The discontinuous character of the diffraction rings demonstrates that the nodule was not composed of randomly oriented crystallites. The strong vertical reflections and the weak lateral reflections show that the reflecting planes were roughly normal to the radii. The absence of sharp reflection spots suggests that the nodule did not contain large crystals. The sharpness of the diffraction rings in their radial direction shows that the variations in intensity along the arcs were not the result of line broadening resulting from extremely small crystals. In the diffraction patterns two rings corresponding to graphite were found. The third and inner ring in the figures originated in the vaseline. The graphite rings correspond to the a and ß lines reflected from the basal planes, showing that the radii of the nodules are the [0001] direction normal to the basal planes of graphite. The picture of the structure that is formed is, therefore, one of aggregates of crystallites. Within each aggregate the c axes of the crystallites tend to align themselves in the radial direction of the nodule, although these axes deviate somewhat in direction by a continuous variation of angle. Correspondingly the basal planes of the graphite crystallites are generally normal to the radii. It is a pleasure to acknowledge the assistance of M. C. Bloom and R. P. Dunphy of this laboratory.

Jan 1, 1952

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By H. P. Reid

PORTLAND cement is manufactured under either of two general proc-esses, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and dry processes.

Jan 1, 1932

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By S. F. Shaw

THE principles involved in lifting oil in wells flowing naturally are identical with those underlying the flowing of wells by means of the air-gas lift, and information of a dependable nature obtained in the study of the air-lift can be applied to wells with natural flow. A well flowing naturally is one in which the lifting is done by means of the gas-lift, for which the gas is supplied entirely by the formation from which the oil is derived. In air-gas lift operations, there is insufficient gas supplied by the formation to lift the oil to the surface in an efficient manner, therefore additional gas for this purpose must be furnished from an outside source. There may, at times, be conditions obtaining in natural flowing wells different from those in wells flowed by gas-lift, but these differences do not at all conflict with the main principles of gas-lift work. One such condition is met with in wells in which the gas supplied by the formation is in considerable excess of that required to lift the oil to surface; this excess may be so great as to reduce the quantity of oil that can be lifted through the particular diameter of casing or tubing that has been lowered into the well. This same condition can be brought about, however, by supplying a large excess of gas from an outside source to an artificial gas-lift well, and a study of the effects obtained from injecting a large excess into the well can be applied directly to handling wells flowing naturally which have a large excess of gas supplied by the underground reservoir.

Jan 1, 1929

By N. W. Wickersham, Ward B. Blodget, Roberts R. Boyd

The year 1926 has seen few radical changes or developments in methods of drilling and handling oil wells, but it has been a year of steady progress and development in deep drilling and production methods. Probably the outstanding development of the year was recognition by the directors of the American Petroleum Institute of the importance of natural gas in the production of oil, and the Institute directors' resolutions in December, 1926, regarding regulation of gas production with oil by state legislation. This matter is extremely important and will receive the attention of the industry in 1927. Advances in Drilling Equipment The history of the progress of deep well drilling is the solution of problems as they have confronted the operator. As the prospects for deeper production have become apparent, methods of penetrating the earth to greater depths have been devised. Rotary Equipment Improvements in the construction and in the methods of operation of rotary drilling equipment have practically caused elimination of cable tools in California for all but shallow work. The rotary drill, from 1910 when it began to be a practical factor in California, has been making steady advances, first displacing cable tools for drilling to the oil sands in proved fields and later displacing the cable-tool outfit entirely. With the perfection of machinery for taking core samples of the formation penetrated, the rotary drill has become generally used for wildcat work, continuous coring being practiced when desirable. Deep Holes The use of the rotary drill has made commercially feasible the opening of oil fields at greater depths than was considered possible with cable tools. Heavier equipment has been promptly supplied as occasion has

Jan 1, 1927

By Luciano B. Oliveira, Angela O. Costa, Sergio N. Monteiro, Luis Guilherme C. Marques

"Biofuels are gaining a relevant role in today’s world not only as a solution for the decreasing petroleum reserves but mainly as a positive contribution to the efforts in global warming mitigation. In Brazil, since 1975, the replacement of gasoline by ethanol started a so-called PROALCHOOOL program, which is now being complemented with the replacement of petroleum diesel by biodiesel. This biodiesel program was officially created in 2005 with mandatory goals, supported by legislation, of 2% addition in 2008 and 5% addition in 2013 into all commercialized regular diesel. In this work, a critical analysis of the Brazilian biodiesel program is presented. The technical aspects related to the different raw materials, including wastes, available for biodiesel conversion as well as the economical conditions associated with production costs and market logistic are discussed. The environmental benefits associated with the retention of greenhouse gases are also discussed.IntroductionToday the commonly accepted fact that the petroleum world reserves are probably passing through a maximum and start declining in terms of the total amount that can be extracted by existing technologies is motivating significant changes in our society. The continuous increase in the price of gasoline and other liquid fuels is an immediate worrisome and visible consequence. However, more than an economical problem, our civilization is already facing the effects of global warming, due to CO2 emission from burning fossil fuels, mainly from coal and petroleum. It is now realized that a large scale solution for these problems demands the prompt substitution of non-renewable fossil fuels by others that, in addition of being renewable, have a relatively lower contribution to the greenhouse gases."

Jan 1, 2008

By H. Landsberg

THE curriculum presented here is an outgrowth of discussions by the Committee on Geophysics Courses of the A.I.M.E. in previous years. It had to be a compromise between the desires voiced by employers of geophysicists, professional geophysicists and the possibilities at an average college. There one has to face the questions of the available teaching staff, the inertia of administrators and teachers set in their ways, and the red tape involved in modernizing antiquated curricula. It is, of course, not ideal to have colleges and universities lag 10 years behind the times. Rather, instead of being prodded by industry, -they should be ahead of industrial needs. There should also be a certain amount of leeway for the student in any college curriculum. All these points had to be considered in drawing up a curriculum, which, instead of being narrowly termed "geology" or "geophysics" was rather called "earth science." It gives the student a chance to specialize in one of the various branches represented by teachers on the faculty of The Pennsylvania State College, giving as options Geology (with subdivisions of Mineralogy and Paleontology), Geophysics, Geography, and Meteorology. Table IA. represents the option of geophysics in the curriculum that envisages that a student may want to make his career in any of the fields encompassed by the American Geophysical Union or in geoexploration. This is, of course, only the start of an education that in most cases will have to be followed by graduate work for complete professional training. The outlined curriculum is definitely of an engineering type and is identical for all of the four options mentioned for the first two years. Specialization will start in the junior year but even thereafter the branches are kept as closely allied as feasible in order to permit a student to change from one to the other (e.g., because of a different aspect in the employment situation) with a minimum of additional work. Table IB shows the geophysics option according to subject matter, indicating the considerable amount of work in the fundamentals of mathematics, physics and chemistry with a liberal number of geology courses, and some engineering. The courses in the field of geophysics are limited-just two lecture courses as a general introduction and one field course, to permit the student a visualization of the correlation between mathematically analyzed physical data and the geological realities. Thesis work is considered essential to teach the student, while he is still in college, some things S. F. Kelly has mentioned as desirable: (I) following of instructions for somewhat independent work; (2) organizing of material, and (3) producing a readable report. This, together with the personal contact with the advising faculty member, will help in forming a student's personality. The seminar course attempts to get the student into the habit of reading current literature, so that he can keep abreast of the times.

Jan 1, 1941