Search Documents

By w. Chruscielewski, T. Domanski

INTRODUCTION Concentration of radon 222Rn and its decay products occuring in the Polish mines of metal-ores call for the necessity of systematic radiation control /Do8la/ both of the working environment and of the miners' personal exposure. The attempts at introducing a system of radiological protection in mines, similar to the ones existing in X-ray or isotope laboratories, took several years and consisted of development of the methods for control of concentration of radon and its progeny in the air, as well as the methods for measuring individual exposure. It was accepted that the assessment of both transient concentration in the air and of personal exposure are basic elements of the control system, which should be implemented independently of each other. Concentration measurement serves to detect and to determine those areas in mines where there is intensive radon emanation, and where current control of the effectiveness of technology introduced to deacrease the concentrations is necessary; personal dosimetry results in the assessment of the actual exposure of miners to radiation. PRINCIPLES OF THE SYSTEM The assessment of working environment is based on concentration measurements of the potential radiation energy of radon alpha decay products. Decentralized assessment is carried out by the special dosimetric service operating in each mine. Dosimetrists are equipped with portable radiometers, type RGR-11, made by the institute of Nuclear Research, Warsaw. The radiometer is presented in Fig. 1. Measurement of filter activity is performed automatically according to Markov's method /Ma62/ or any other method. Simultaneously to potential energy measurement the dosimetrists are measuring the dust concentration in the air and ventilation rate. Ventilation service looks for correlation between those indices and the concentration of radon daughters in the air. Derived Air Concentration /DAC/ for concentration assessment was accepted to be 6.25 10-6 Jm-3 /0.3 WL/ according to ICRP recommendation /Publication No. 24/ /ICRP77/. If environmental measurements reveal potential energy concentration exceeding the value of 0.3 DAC at working places, the miners employed there are subject to individual control of personal exposure. Individual exposure measurement is carried out centrally by the Institute of Occupational Medicine in [Lodz] for all metal-ore mines. Miners who are to be included in the control scheme are referred by a mine management to the Institute where they are registered and assigned a dosimeter. A passive dosimeter with

Jan 1, 1981

By Robert E. Brand, Strathmore R. B. Cooke

For a study of the bonding that occurs in magnetite pellets during oxidation, cubes of magnetite, hematite, and quartz were prepared, each with one surface polished and nearly optically plane. These faces were fired together under pressure and at various temperatures to determine whether bonding would occur. Sections of surfaces that bonded were examined microscopically. An attempt was made to measure the strength effected by this treatment. EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."' The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen. The materials used were magnetite, hematite, and quartz. The magnetite was coarsely crystalline material from western Montana, the hematite was Itabira ore from Brazil, and the quartz was of optical grade but of unknown origin. A high-grade Lebanon (Pennsylvania) magnetite concentrate was used to prepare briquets for the investigation of bonding strength. Analyses of the iron oxide materials are given in Table I. The specimens for furnace treatment were prepared with a carborundum cut-off wheel, which cut the minerals into cubes approximating % in. along each edge. Care was taken to make the sides as parallel as possible. The edges of the faces to be polished were beveled, and the cubes were mounted in brass rings with sealing wax, this being essential to prevent the specimens from rocking during polishing. To prevent excessive friction, the wax was recessed so that only the brass ring and the face of each specimen would be in contact with the polishing lap. Each specimen was then ground with No. 600 carborundum to produce a level surface before polishing. The Graton-Vanderwilt process was not used for polishing because of the long time required by this method, but several other methods were tried. Cloth laps using levigated alumina or chromium oxide did not produce the desired polish. Satisfactory results were obtained by means of a pitch lap: which was used for all the mineral cubes, with levigated alumina as the polishing medium. The lap was operated in a machine similar to those used in the preparation of single optical surfaces. It was run at low speeds and moderate pressures, and polishing was stopped occasionally to prevent overheating of the lap. A good polish with flat surfaces could be obtained in about 5 min. After polishing the sealing wax was removed either in hot water or in a solvent such as turpentine.

Jan 1, 1955

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By Charles E. Mann, Douglas J. Lootens, Rufino B. Bomasang

INTRODUCTION The economy of the Philippines, like that of many other developing nations, has been severely strained by the rapid escalation of imported crude oil prices over the past decade. In an effort to reduce its dependence on imported crude, significantly increased emphasis, both in the public and private sectors, is being placed on the rapid development of Philippine coal resources. This paper is designed to present an overview of the Philippine coal industry, its historical development, present status, and future potential. COAL RESOURCES AND RESERVES In 1977, a British consulting firm collated all available data on Philippine coal resources and estimated the total coals potential at about 0.9 to 1.4 billion metric tons (mt). In 1981, using more recent data the Philippine Bureau of Energy Development (BED) estimated the potential at 1.7 billion mt. The BED estimated the proven coal reserves at 257 million mt. These coal resources are scattered throughout the major islands comprising the Philippine archipelago. However, about 52 percent of the currently proven reserves are located in the tiny island of Semirara between the islands of Mindoro and Panay. About 25 percent is located in the Cagayan Valley in northeastern Luzon while 13 percent is located in Mindanao. The remaining 10 percent is scattered in the islands of Cebu, Samar, Mindoro, Negros, Polillo, Batan, and Catanduanes. The bulk of Philippine coal is sub-bituminous in rank. Some bituminous coal with coking properties has been reported in Malangas, Zamboanga del Sur in western Mindanao, and in Catanduanes, but the exact tonnages have not been accurately established. It is believed, however, to be at most 5 million tons. A little semi-anthracite coal exists in Malangas with the remaining unmined reserves estimated at a little more than one million tons. Table 1 shows the quality ranges of Philippine coal deposits.. Figure 1 shows the distribution of known Philippine coal resources PHILIPPINE COAL PRODUCTION In 1981, total coal production was 330,720 mt. Though modest by world standards, this was the highest production figure in Philippine coal mining history. This came from 25 mines, mainly small scale underground mines of capacities varying from 10 to 100 tons per day (tpd). The actual production capability was about 800,000 mt in 1981, but the producers had to scale down production to the level of local demand. Even then, some 50,000 tons of coal remained unused by year-end. The 1981 production came from the following areas: Cebu 224,751 mt (68%) Zamboanga del Sur 57,095 mt (17%) Semirara 13,222 mt (4%) Polillo 17,132 mt (5%) Cebu has always been the main source of Philippine coal production. Coal mining has been carried out in Cebu for the last 50 years, although it has been characterized by a very crude mining technology. Due to the limited size of coal deposits and complicated geology, however, Cebu's share of the total national production is expected to go down to only 10 percent by 1985. Except for Semirara's open-pit production, the balance of Philippine coal production comes from underground mines. These underground mines generally use room-and-pillar methods, except for those at Zamboanga del Sur and Polillo which use modified longwall methods patterned after those used in Taiwan. Due to the much higher mining recovery, most underground mines are now planning on switching to longwall. At Semirara, an open pit mine is now being developed for a one million ton per year capacity by 1984, and will then be the largest Philippine coal mine. While present earthmoving work is done with bulldozers, loaders, and trucks, the main coal extraction equipment will be bucket wheel excavators imported from Austria. PRESENT COAL UTILIZATION Existing coal production is sold mainly to coal- fired cement plants and power plants. The balance is sold to a sugar central, a coconut oil mill, a food processing plant, and two plants producing carbide and ferro-silicon alloys.

Jan 1, 1982

By Nagy El-Kaddah, T. T. Natarajan

This paper describes a novel approach for modeling three-dimensional electromagnetically driven flow in inductively stirred systems, and its application to modeling electromagnetic and flow phenomena in sub-mold rotary stirring of billets. It is based on a new T-\jf potential formulation of electromagnetic field, which does not require the calculation of the field in free space. A finite element algorithm has been developed for solving the electromagnetic field and Navier-Stokes equations in the fluid flow domain. The computed results have shown that the electromagnetic force field generates a strong rotational flow within the vertical section covered by the stirrer, and a relatively strong secondary flow beyond the stirrer. It has also been shown that the rotational and secondary flows were driven primarily by the vorticity of the force field at the billet corners. The induced flow in the molten pool was found to be turbulent and the effective mixing region in the molten pool was about three times the length of the stirrer. The mathematical approach presented in this paper provides the theoretical framework for quantifying these effects for any given stirrer configuration and operating parameters.

Jan 1, 1999

By Guillermo Chong Díaz

A brief overview of industrial mineral exploration and exploitation in Chile is given. World class deposits of salt, lithium, nitrate, and iodine are present in northern Chile. The potential for further exploration and exploitation of these deposits, as well as the substantial reserves of other mineral commodities such as gypsum, anhydrite, volcanic rocks, and borates are discussed. In conclusion, industrial minerals mining in Chile has considerable potential, particularly as joint ventures between foreign and domestic companies. This has been demonstrated in the extraction of nitrates, lithium, iodine, and diatomites. However, as outlined in this paper, a number of factors need to be overcome before the true potential of the Chilean industrial minerals industry can be realized.

Jan 1, 2001

By Barnett J. C

The arid and semi-arid region of Western Australia occupies about two-thirds of the State equivalent to an area of about 1.8 million sqkm. Groundwater demand in this area has historically been linked to the pastoral andmining industries commencing with the gold discoveries in the Eastern Goldfields some 100 years ago. Substantial increases in demand have occurred in the past two decades initially as a result of nickel discoveriesin the early 1970's and more recently the rapid resurgence of the gold mining industry. Mineral exploration and development in the Great Sandy Desert at Telfer (gold) and Kintyre (uranium) and in the Great Victoria Desert at MulgaRocks (uranium) has also been accompanied by detailed groundwater investigations.

Jan 1, 1988

By B. F. Zwick

The entire production of oil in Ecuador so far has come from the Santa Elens Peninsula, Province of Guayas. Both the shallow fields of the northern and the deeper fields of the southern part of the peninsula have been in constant exploitation, though the former are of doubtful economic value. In Table I herewith, which commences with the total amounts produced by the various companies up to 1940, annual company totals are given for the succeeding years. The figures for 1944 have been partly estimated. Table 2 gives figures on casinghead gasoline. Shell Company of Ecuador (formerly known as Anglo-Saxon) has continued active exploration in the Oriente region east of the Andes, and during 1944 the Company's first wildcat well was spudded in. International Ecuadorean Petroleum Co. (formerly International Petroleum Co., Limited) has pursued an active exploration campaign since the latter part of 1939, and a drilling string was placed in operation about a year later. A second string of tools was added during 1943 and a third a few months ago. Ten wildcats, all dry, have been completed in this period, two wells are drilling at the present time and other locations are on the program. Seven of the wells thus far drilled are in the area between Guayaquil and the Santa Elena Peninsula, one up the Daule River beyond Balzar, one on Puna Island in the Guayas Estuary and one in the northern province of Esmeraldas. Both the present drilling wells are in the Guayaquil-Santa Elena zone. The situation in regard to concessions has changed during the past four years because I.E.P.C. has made its selections from the extensive Daule-Guayas Study Concession, as a result of which large tracts were returned to the Government; because of the expropriation of the holdings of the "Ecuapetrol," a German concern whose acreage has passed into other hands; the Peruvian-Ecuadorean boundary settlement, which has reduced Shell's holdings somewhat; and the transfer of most of the holdings of the Cia. Minero-Petrolera del Pacifico to I.E.P,C. The greater part

Jan 1, 1945

By Oliver B. Hopkins

The Peruvian production increased over 3 million barrels from 1933 to 1934—from approximately 13¼ million barrels to over 16¼ million barrels—bringing the cumulative production of the country up to 171 million barrels. Most of this production, as well as most of the increase in 1934, came from La Brea-Parinas Estate, the property of the International Petroleum Co., Limited. In 1932 Peru stood eleventh among the oil-producing countries of the world, but in 1933 her production exceeded that of Trinidad, Argentine and Colombia, which placed her in eighth position. In 1934 Peru's production was exceeded by that of Colombia by about one million barrels, and by that of the Argentine by about 1½ million barrels, thus placing her in tenth position. After several years of relative inactivity in drilling and exploration there was a noticeable increase during 1934 in both of these lines of activity. Oil Fields La Brea-Parinas Estate.—Production on the La Brea-Parinas Estate. reached a significant total of 85,080 bbl. as early as 1891. It increased to over one million barrels in 1912, and to over 10 million barrels in 1929, and in 1934 it reached an all-time high of over 14 million barrels. The total production from 1890 to 1934 was 133,784,609 barrels. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. One was a heavy outfit for drilling a deep test and the other two were lighter outfits for deepening wells in the newer section of the field, where the gas pressure was too high to permit safe drilling with standard tools. During 1934 a total of 28,127 ft. was drilled, 66 wells were deepened, and 6 new wells were completed. At the end of the year 2844 wells had been drilled on the Estate, of which 1814 were still productive. The remaining 1030 wells represent abandoned producers or dry holes. The total area that has been productive up to the present time is estimated at 13,369 acres. An interesting article on the various phases of operations of the International Petroleum Co. was written by Arthur Iddings and published in The Oil and Gas Journal (Dec. 27, 1934).

Jan 1, 1935

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By J. W. Paul, J. N. Geyer

The measures overlying some coal beds are under stress as the result of geological movements after the measures have been deposited. The removal of the coal in the process of mining induces additional stress in the roof measures. Certain types of deposits have sufficient inherent strength to be self-supporting over definite width of excavations and the stress is adjusted without appreciable movement of the material, to the extent that no part of the material will become detached and fall. The uplifting of the measures in geological time often results in the establishing of cleat planes or planes of weakness in the measures overlying the coal, and these planes generally have a uniform direction. Measures that have not been subject to uplifts are less liable to have noncompensable stresses, although any method of underground mining results in the creation of stress in the roof measures over the excavations and over the coal pillars. The immediate roof measures extending upwards of 10 to 15 ft. above the coal give the greatest concern in maintaining the roof in the advance work in the solid coal. Immediate measures which are inherently weak often may be scaled and supported for indefinite periods by a system of timbering. As an excavation is made, the pillars adjoining must take on the weight previously supported by the coal removed. The roof over the excavations takes on the function of a beam and if too weak to be self-supporting it will fail either through shearing or bending, and the roof cavity may enlarge until a self-supporting arch is formed. As support is removed by taking the coal away, there is a tendency for the roof members to move toward the excavation in an effort to compensate the stress; particularly is this true where there is an overlying bed of clay, which may act as a lubricant on which adjoining members may slide. Unstabilized stresses, plus the force of gravity, plus the inherent strength of the material, govern the tendency of mine roof to fall when not supported by timber. In general, most mine roof depresses when the coal is removed. This depression may be in the nature of a sag as the result of bending, or the edges of the pillar may break away or the floor may come up or heave.

Jan 1, 1934

By George H. Ashley

The Legislature of the Commonwealth of Pennsylvania at its last session passed a new act dealing with barrier pillars, which may have a wide interest in other states. In the past the laws of Pennsylvania have required that the superintendent of a mine "shall not permit the mining of coal within 50 ft. of any abandoned mine containing a dangerous accumulation of water, until said danger has been removed by driving a passageway to tap and drain off said water, as provided for in this act: Provided, That the thickness of the barrier pillars shall be greater aid shall be in proportion of one foot of pillar thickness to each one and one-quarter feet of water head, if in the judgment of the engineer of the property and that of the district inspector it is necessary for the safety of the persons working in the mine." Thus it has happened that a thickness of several hundred feet has necessarily been left in pillars in mining. It has seemed to many in the mining industry that this left an unnecessary amount of coal in pillars, and did not provide that the pillar be left equally on the two sides of the mine. As a result the General Assembly of 1927 by Joint Resolution authorized the Governor to appoint a Commission of "seven prominent citizens, of whom four shall be recognized mining engineers, one shall be a hydraulic engineer, one a geologist of recognized standing in his profession, and one a State mine inspector from the bituminous coal mining district, to investigate and report upon barrier pillars in the bituminous coal region." The Governor appointed the following Commission: Morris Coulter, Clearfield Bituminous Coal Corp., Indiana, Pa.; A. E. Roberts, Monroe Coal Mining Co., Revloc, Pa.; George T. Lewis, Westmoreland Coal Co., Irwin, Pa.; Morris Knowles, hydraulic engineer, Pittsburgh, Pa.; Thomas A. Mather, State Inspector of Mines, Tyrone, Pa.; A. B. Jessup, Anthracite Coal Operators Association, Jeddo, Pa.; George H. Ashley, State Geologist, Harrisburg, Pa. Mr. Coulter was elected Chairman and Mr. Ashley, Secretary. This Commission held meetings in Harrisburg, Johnstown and Pittsburgh. It obtained and considered the laws and experiences of other states and European countries. Some of its members conferred at length with the directors and other members of the U. S. Bureau

Jan 1, 1930

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By Colin M. Sargent

ALTHOUGH annealing twins are frequently observed in many fcc metals, their occurrence in aluminum is relatively rare. ~ahn' in his review of twinning has listed only a few references to observations of twins in aluminum, e.g., Refs. 2 and 3. They have also been shown to occur in evaporated aluminum layers.4 During the present work, several annealing twins were studied in aluminum. The specimens of 1099-grade aluminum had the following thermomechanical treatment: deformed 90 pct by rolling, partially re-crystallized, further deformed 60 pct to a final thickness of 100 p, then annealed for 24 hr at 120°C. This treatment produced several annealing twins—-about ten per electron microscope specimen. The specimens were produced by the window technique and examined in a Phillips E.M. 200 operating at 100 kv. A typical twin boundary is shown in Fig. 1. For several of the twins studied the twin plane could be tilted so that it was parallel to the electron beam, e.g., Fig. 2. The associated diffraction pattern, Fig. 3, shows the twinned relationship between the grains. The twinning plane in each case was (111). Use of a reflection common to both the twin and the matrix,* i.e., using reflecting planes parallel in the twin and the matrix, the coherent twin boundary becomes invisible and only the noncoherent segments of the stepped boundary are seen, e.g., Fig. 4. Trace analysis of the boundaries showed that the long straight portions were invariably the twin plane; i.e., these portions are coherent. The planes of the shorter segments are shown by Fig. 5 to be (551 1, (7111, and {211).

Jan 1, 1969

By Richard Dunmore

Tests of the MRDE firedamp prediction method have been carried out in a number of longwall districts with different conditions. The method itself and its development have been described previously At many test sites the prediction has been good, i.e. the calculated gas emission levels have agreed with measured values, averaged over a period of many weeks, within a few percent. In other cases, where there have been larger discrepancies between calculation and measurement, investigations have shown that these may be attributed to particular conditions of mining or geology. Recognition of these conditions in advance of mining is clearly desirable to improve the accuracy of the initial prediction. It has been shown that variations in gas emission rates depend largely on coal production in terms of the weekly advance of the coal face. Although there appears to be a random element present, variations in gas emission levels calculated from changing face advances agree well with measurement. The accuracy of prediction therefore depends on how well face advance can be forecast and needs to be updated as the working proceeds in the light of the face performance actually achieved. Continuous monitoring of the mine environment provides the information necessary to compare actual gas emission with predicted levels, and computerised systems make it possible to carry this out in real time. Predictions can thus be adjusted to take account of emission levels measured in previous weeks These adjustments, whether they are made after the first few weeks or subsequently during the district life, would also be used to alert management to particular abnormalities or significant changes in gas emission.

Jan 1, 1982

By G Pitkin, D Sorley

The purpose of any consultancy is to provide a superior service for their client. Organisational structure is a key element in providing this service and differentiating between consultants.In an organic organisation the emphasis is on effectiveness, problem solving, responsiveness, flexibility, adaptability, creativity and innovation. Such an organisation is able to respond in a timely manner to change because employees are empowered to be creative, to experiment and to suggest new ideas. The process of innovation is triggered by employees throughout the organisation in a collaborative manner.Problem solving becomes a core competence of the consultancy. A multidisciplined approach arrives at superior solutions that are rigorous, holistic, achievable and often novel. It allows the mining consultancy to extract the most from a very talented and experienced team.This paper highlights the advantages of an organic structure for a mining consultancy and how to implement such a structure. It draws on examples of innovative problem solving from feasibility and strategic studies carried out in Australia and Africa.CITATION:Pitkin, G and Sorley, D, 2016. Organic management structure – its advantages in a mining consultancy, in Proceedings International Mine Management Conference, pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By A D. Price, W J. Germs, O Patterson, T R. Weaver

"Understanding controls on groundwater and surface water flow and quality at mine sites throughout all mine stages is critical to effectively manage environmental impacts over the entire mine life. Monitoring forms is an essential component of this proof of understanding. Typically, monitoring programs at mine sites have been developed in the framework of existing conditions. However; recognition of the challenges of climate change and the performance of mines during recent extreme events in Australia has highlighted the need to develop monitoring programs that are resilient and responsive to changing environmental conditions. Water monitoring programs need to be effective under a range of environmental conditions, potentially not historically experienced.This emerging challenge requires cross-disciplinary teams to work together to understand issues including: representativeness of background conditions to longer-term conditions at the mine site sensitivity of mine and closure designs to changing climate and hydrologic conditions methods of performance (eg water quality or quantity) failure during extreme climate events such as flood or extended drought.These understandings come together in a detailed conceptual and, in many cases, numerical hydrologic model that considers the mine-water environment under a range of conditions. The groundwater, surface water and water quality monitoring programs that are developed from the conceptual model need to be sufficiently responsive to be effective in the face of such changing conditions, with results in turn informing the conceptual model. Extended drought, major floods and changing weather patterns can alter recharge and discharge areas, oxidation profiles and ultimately, the contaminant flux estimates that would have contributed to mine design parameters and performance. Unless these effects are considered in the spatial and temporal design of the monitoring program and within the parameters monitored, the resultant program may fail to capture data that are critical to evaluating environmental impacts from mine sites.Developing and implementing a water monitoring program that considers these issues can build confidence in mine performance under a range of conditions, leading to increased confidence by all stakeholders in long-term mine performance during and after closure.CITATION:Weaver, T R, Price, A D, Patterson, O and Germs, W J, 2013. Developing resilient water monitoring programs in changing climate conditions, in Proceedings Water in Mining 2013, pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957