Search Documents

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By McNay L. M

Two field studies to monitor fill pres sures and vein-wall deformation were conducted in mines of the Coeur d'Alene mining district in Idaho. Both operations employed cut-and-fill mining techniques in nearly vertical veins aver- aging 10 feet in width, and backfilled with classified mill tailings. Hydraulic pressure cells were used to measure transverse, longitudinal, and vertical pressures within the backfilled stopes. Rock bolts extending into the manways and mechanical closure devices were used to monitor vein-wall convergence. Continuous recorders were used with selected pressure cells to prolong the life of the installation. Transverse pressures in excess of 600 psi and stope wall closure up to 22 inches were re- corded. Closure rates were higher at midheight of the stope than they were near either sill, indicating that the vein walls react similarly to a beam supported on each end.

Jan 1, 1973

By D. A. Elgillani, M. C. Fuerstenau

In this paper, oxidation potentials measured in the presence of various concentrations of cyanide, ferro-cyanide, and ferricyanide and ethyl xanthate at various values of pH are related to flotation response. Eh-pH diagrams are presented to show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide on the depression of pyrite with xanthates as collector has been the subject of a number of investigations,'-6 and several theories on the mechanism of depression have evolved from these studies. Wark and Cox7 and Gaudin8 have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues9-11 have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland 12 has shown that although both of these theories accurately describe the relation between pH value and cyanide addition at constant collector addition, they fail to describe the relation between pH value and the amount of collector required to cause flotation. Taggart 13 suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar4,6 has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg per liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10. These results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface. Gründer and Bornl4 have stated that depression may be due to the formation of the compound K2Fe(II)Fe(CN)6 at the pyrite-solution interface. This compound is thought to be an interaction product between the K2Fe(CN)6-2 ion from solution and the Fe++ ion at the pyrite surface and, accordingly, K4Fe(CN)6 should depress pyrite at least as effectively as KCN. This was proven experimentally, but there was no simple relation between the depression of pyrite and the concentration of either KCN or K4Fe(CN)6 in solution. In view of the many mechanisms that have been proposed for pyrite depression by cyanide, it is apparent that a clear understanding of the phenomena occurring in these systems is lacking. One reason for this may be the fact that the species responsible for pyrite flotation in the presence of xanthate is not the xan-thate ion but rather dixanthogen.15 Since the oxidation of xanthate to dixanthogen is dependent on the oxidation potential of the solution, it would seem that knowledge of these potentials would be a requisite to understanding the pyrite-xanthate-cyanide system. It is the object of this paper to measure both the oxidation potential and pH of the pyrite systems in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and xanthate and to relate these values to flotation response. EXPERIMENTAL MATERIALS AND 'TECHNIQUES In the experiments discussed here, pure potassium ethyl xanthate was used as collector, and reagent grade potassium cyanide, potassium ferrocyanide, and potassium ferricyanide were used as depressants. Reagent grade HC1 and KOH were added for pH adjustment. Conductivity water, made by passing distilled water through an ion exchange column, was used in all experimental work. Two natural samples of pyrite were used in the investigation. Sample preparation for flotation included dry grinding with a mortar and pestle and sizing the product to 100 x 200 mesh. Prior to flotation, a 0.75-gm sample of pyrite was added to a solution containing a known amount of depressant at the desired pH value, and the system was conditioned for 4 min. Following this, a known amount of collector was added and the system was conditioned for another 4 min. The pH — termed flotation pH - was measured; the pulp was transferred to a Hallimond cell, and flo-

Jan 1, 1969

By K. Sarveswara Rao

"Any innovative approach made in non-ferrous metallurgical industry centers upon developing new processes, saving materials, improving production quality, and bornagain materials. Aqueous processing is commonly used to treat lean grade or more complex ore bodies. Its sustenance largely depends on energy and environmental compliance including water and wastewater management. The present paper focuses the importance of using particle size distribution and surface area measurements during ammoniacal dissolution of a Cu-Pb-Zn sulphide bulk concentrate and with an overview of the effect of water salinity on the process chemistry and residue mineralogy. Accordingly, an effort is made here to discuss the emerging perspective and highlight the recent successes and trends in terms of energy savings in non-ferrous hydrometallurgy.IntroductionThe nature and structure of the global energy industry is likely to change significantly in the 21st Century. Rabago et al [1] have comprehensively discussed how the mining and minerals industries can adapt to the challenges and opportunities posed by trends and drivers in global energy use. According to the authors, the drivers of sustainability include water, efficient energy use, climate modification, transportation technologies and energy security. Sustainability and competitiveness for the minerals industry will depend on natural capitalism, resource efficiency, new processes, saving materials, improving production quality, born-again materials and the solutions economy. Based on this motivation, the theme of the present paper is centered upon applications as relevant to energy and sustainable development in non-ferrous hydrometallurgy."

Jan 1, 2009

By J. Nesset, F. Rosenblum, P. Spira

Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 500°C. However, most concentrates show little or no propensity to self-heat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.

Jan 1, 2001

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961

By K Matsui, T Sasaoka, S Kubota, Y Yosh

A large amount of wastes from the preparation plant is produced. The properties of these wastes vary depending on the mineralogical contents of the mother rock in which the coal is embedded. The waste quality depends on the method of mining and cleaning. The waste mainly consists of clays, quartz, carbonaceous materials, mica, pyrites and so on. About 55 per cent of coal-ash is now utilised and the remains are disposed of at the disposal sites, however, the life of the disposal site is limited. Moreover, it is difficult to find new disposal sites. Therefore, it is requested that the percentage of the utilisation of the coal-ash be increased in every field in Japan. So, it is very much available if the injection material for natural/artificial openings can be applied on the cement that is added to flyash. Among the man-made pozzolans, a flyash is probably the most successful component used in grout injection. When flyash is added to Portland cement concrete, the same kinds of oxides as those of the cement are being added. As an injection component, flyash acts, in part, as a fine aggregate and, in part, as a binding component. However, there is not a substantial alteration of the properties of the original component. From these points of view, in order to clarify to what degree the flyash content affects the properties of the injected grout mixture; different combinations of flyash, Portland cement and water were considered by means of several experiments.

Jan 1, 2003

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

By James E. Dailey

Marine mining is driven by profitability, and profitability is driven in turn by people and equipment that can work productively and safely at sea. Design challenges faced by the marine mining community have much in common with those faced by the offshore construction community. Technical solutions continue to move freely between both communities. A brief pictorial history summarizes the evolution of offshore construction technology as it grew in the Gulf of Mexico and expanded worldwide. Attention is focused on those areas of platform and pipeline construcion where there is potential technology application to underwater mining. An especially difficult challenge faced by both communities is work in the surf zone. Some innovative concepts for surf zone construction operations are presented and possible applications to marine mining are suggested.

Jan 1, 1989

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

The smelting of the Broken Hill lead concentrates at the Broken Hill Asso,ciated Smelters produced, among other products, approximately 4,900 ounces of gold and 8,800,000 ounces of silver during the year ending June 30th, 1938. The following table shows the actual amounts of gold per ton of lead concentrate produced during this period at the important mines. The total gold in the period is calculated from the number of tons of lead concentrates produced, and by comparison with the production' of silver, shows thatthere is no constant relation between the amounts of gold and silver.The fact that no gold is seen during milling, even when gravity concentrating tables are employed, signifies that the gold does not occur as occasional coarse particles.Further, as the values increase considerably in the flotation slime, it can be inferred that the gold occurs as minute inclusions in one or more of the minerals in the lead concentrates.The four most abundant minerals in the lead concentrate are galena, zinc blende, chalcopyrite, and...

Jan 1, 1940

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

By E. H. Rose

IN these days of the spectacular in research and technological accomplishment, it is easy and natural to overlook some of the applications to everyday life of recent developments of a more pedestrian kind, or to fail to realize that sometimes two or three of the latter may be combined to serve a novel purpose in fields other than those in which they grew. The present remarks are to point out three such developments which might be combined to apply to an everyday function of the A.I.M.E. as an organization. By its Constitution, the A.I.M.E. is organized "to promote the arts and sciences connected with . . . minerals and metals, and the welfare of those employed in these industries . . .; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate . . . among its members the information thus obtained . . .; and to . . . maintain . . . a library." By these words of Article I the profession of mining and metallurgy is recognized to involve many arts and sciences, of which the art and science of exchanging information is a leading one. As to methods of preparing or securing papers, the Constitution is silent.

Jan 1, 1944

By H. V. R. Von Rahden

The expertise of the industrial mineralogist has not always been sufficiently used in decision-making in the minerals industry in South Africa. The mineralogist can make a contribution at al stages of the exploration programme, from the time of discovery of a geological target area, through metallurgical testwork and pilot-plant studies, to the production of a saleable product. This indicates that the activities of the industrial mineralogist should be more closely integrated with those of the exploration geologist and the extraction metallurgist in order to provide management with a meaningful picture of the economic potential of an ore deposit.

Jan 1, 1997

By Kevin L. Gering

A detection method and apparatus have been developed to perform real-time measurement of aqueous free cyanide, C-. A laboratory prototype can measure cyanide ranging from 5 micrograms ,per liter to 100 milligrams per ?liter for analysis times as short as 2 minutes per measurement. Sample size per measurement is typically only a few mI, thus? minimizing the waste volume produced from spent samples. The basis for this detection device is a quantifiable, stable affinity between the electrode material and free cyanide in the sample; The electrode exhibits piezoelectric behavior, allowing it to be used as a microbalance. This technology 'has experienced two generations of laboratory prototypes, and has been thoroughly tested to determine the operational sensitivity toward process variables such as pH, competing reactions, etc. The speed and ,accuracy of this method make it superior to conventional wet chemistry methods used for quantifying cyanide levels in water. A device based on this technology could be useful in areas involving process monitoring and environmental compliance, .particularly in the cyanide-based leach mining industry. Interest for this detector has been shown by the gold mining industry and others. Patent application is in progress.

Jan 1, 1998

By Harry L. Siebert, Thomas Gelormino

Rock excavation in urban areas occurs with maximum public exposure and, with the aid of explosives, is one of the challenges facing this industry today. Such excavation is also a hidden factor in areas of new growth, revitalization or upgrading existing facilities in or near urban areas.

Jan 1, 1985

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By Ernest M. Spokes, Martin A. Thieme

A simulation model developed to analyze scraper-pusher utilization in open pit mining systems is described. The mining simulator discussed was developed as a tool to aid management in evaluating alternative open pit haulage schemes and to reduce the risk involved in the selection of equipment.

Jan 1, 1973

By C. S. Barrett, O. R. Trautz

PREVIOUS investigations have shown that lithium is body-centered cubic from near its melting point to the temperature of liquid air1,2,3 Nevertheless there was an incentive to search again for a transformation at low temperatures: C. Zener4,5 has remarked that the low value of the elastic modulus (11 - C12)/2 of body-centered cubic metals and alloys implies a rapid increase in free energy with decreasing temperature, which would favor the occurrence of a transformation; also the shear movement to which this modulus applies is one that can transform a body-centered cubic structure into a slightly distorted face-centered cubic structure. It was confirmed that lithium does not transform spontaneously at liquid nitrogen temperature, but it was found that a transformation can be induced at this temperature by cold working the metal,6 and at slightly lower temperatures a different transformation occurs spontaneously. Transformations were also found in solid solutions of magnesium in lithium. THE NATURE OF THE TRANSFORMATIONS Before presenting a detailed treatment of the technique used and the specific data obtained, it would be well to give a brief survey of the general characteristics of the transformations. A new crystal structure begins to form spontaneously in a specimen when it is cooled below a critical temperature. In lithium the structure appears to be close-packed hexagonal; in the Li-Mg alloys most of the diffraction lines (but not all) are near those for hexagonal lithium. The transformation proceeds as the temperature is lowered and soon stops if the temperature is held constant or raised. The course of the transformation on cooling is indicated by the curve at the lower left of Fig I. This curve is drawn in stepped fashion because the transformation goes by discrete steps with audible clicks. Because of the similarity to the decomposition of austenite into martensite in steels, it seems appropriate to designate the beginning of the spontaneous transformation on cooling as the Ms point. On heating to room temperature after the low temperature treatment only the usual BCC structure is found. On heating, the low temperature modification begins to disappear at a temperature which will be designated as Ac. The transformation on heating is halted when the rise in temperature is halted. The temperature must be raised 40 to 50°C above Ac before the reversion is complete-an interval which is sensitive to the rate of heating and to the time of holding at temperatures above Ac. This behavior on heating thus has similarities also to the formation of martensite in the cooling of steels.

Jan 1, 1948