Search Documents

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

By William F. Kane, Eric C. Drumm

Rock slope failures in the Great Smoky Mountains of Tennessee are a continuing problem. A study of the geotechnical factors affecting such slopes was conducted in this geologically complex region. Seven rock slopes, five of which had undergone failure, were identified and mapped. Other parameters were mapped in addition to the standard geologic and geometric parameters. These were joint frequencies across and down the slope, and surface hardness from Schmidt hammer tests. Regression analysis on the various data revealed that Schmidt hammer hardness correlates very well with joint cohesion back-calculated from failure geometries. This approach suggests an alternative means for estimating joint strength.

Jan 1, 1986

By P. Somasundaran, G. E. Agar

The role of calcium, phosphate, and fluoride species in determining the zeta potential of apatite in aqueous solutions was investigated in this study. The zeta potential of apatite was determined by streaming potential measurements over a wide range of concentrations of potassium nitrate, calcium nitrate, potassium dihydrogen phosphate, and potassium fluoride solutions at various pH values. While the addition of phosphate made the apatite surface more negative at all pH values, calcium caused a significant increase of the zeta potential only when the zeta potential was negative. Fluoride addition had only a minor effect on the zeta potential, but both negative and positive values were increased.

Jan 1, 1973

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By Walter Kauenhowen

Germany's crude-oil production during 1937 totaled 3,174,157 bbl., an increase of 1.9 per cent over the 3,112,494 bbl. produced in 1936. According to official published data, and using a conversion factor of 1 metric ton = 7 bbl., the oil production of Germany in 1937 by fields was as follows:

Jan 1, 1938

By Jung-Keuk Kang

Recently, the Korean government prepared a strategy for deep seabed mining, which consists of three stages for 20 years until 2010. The first step of the program is focused to conduct deep seabed exploration until 1993. The apparent "hurry-and-spend to catch-up" policy that the Korean government has shown in deep seabed mineral exploration was motivated by an effort to qualify a prerequisite requirement to be a pioneer investor as a developing country under the terms of Resolution II and the New York Understanding. Since 1983, KORDI (Korea Ocean Research and Development Institute) under the auspices of the Korean government has carried out deep seabed mineral exploration. The KORDI had a joint exploration program with USGS from 1989 to 1991 aiming to evaluate the potentiality of manganese nodule in the western part of Clarion-Clipperton Zone as well as that of manganese crusts in the western Pacific. In 1992, Korean government accelerates its program by the confirmation of national policy and the equipment of new built research vessel, Onnuri-Ho. The RIV Onnuri-Ho is about 1400 G/T, which is equipped with various advanced instruments including GPS, multi-beam echosounder (Seabeam 2000), multi-channel seismic system, and MDM system.

Jan 1, 1992

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows : I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

By R. J. Borg, C. E. Birchenall

The self-diffusion coefficients for a iron have been deternzined between 980° and 1167° K using Fe55 as the tracer. With decreasing temperature the diffusivity was found to decrease more rapidly than predicted by the Arrhenius equation in the region of the Curie temperature. The diffusion coefficients obtained well above the temperature of the magnetic transformation are more precise ard differ substantially from all the previously reported values. In the temperature region beginning at least 50" above T,, the diffusion coefficient is given by D = 118 (±2) exp 1 HE self-diffusion coefficients for a iron have been reported previously as the result of four independent investigations The general lack of agreement and the poor precision of most of the previous work prompted the redetermination by the present authors. The possible effect of the onset of ferromagnetism upon the diffusivity5 provided an additional impetus for this investigation. The earlier measurements of Birchenall and Mehl1 gave low values for the diffusion coefficient at temperatures below the Curie temperature, Tc. However, the precision of these measurements is not sufficient to establish an indisputable correlation between the low values and the magnetic transformation. The results of this investigation along with all the previous ones are shown in Fig. 1. EXPERIMENTAL Small rectangular samples, approximately 1 by 0.5 by 0.3 cm, of high-purity iron (Vacuum Metals Corp., "Ferrovac") are first heated in hydrogen at 900°C for24hr in order to remove possible trace amounts of dissolved carbon and oxygen. The small

Jan 1, 1961

By Simon W. Houlding

This paper summarizes recent developments in computer modelling and estimation technology. Significant improvements in computational and modelling efficiencies have advanced technical computing to the stage where, for the first time, it can be realistically applied to short-term mine planning and production control. Real-time interactive grade estimation of complex shapes, volumes and grade distributions, based on immediate turn-around of production sample grades, is now possible. An added benefit is the ability to produce complete geostatistical estimates which include confidence limits. These can be incorporated into the decision making and risk assessment processes of production control. Why the need for new technology? What is wrong with the conventional methods which have sufficed for the last thirty years? The response is manyfold. They suffer from inefficient computational processes and conflicts with geostatistical theory. They are responsible for constricting the flow of information between the disciplines involved in the mine production process. Finally, it is illogical to approximate irregular geological and mining volumes with orthogonal sets of rectangular blocks. Geological materials do not occur in block formation; and mining methods which excavate rectangular blocks have yet to be developed. Other computer based technologies have evolved out of the dark ages of rectangular approximations and have successfully dealt with irregular three-dimensional geometries. It is time for computing in the mining industry to follow this example and take full advantage of available technology. To provide the necessary background, consider the basic requirements for successful implementation of technical computing within the mine production process.

Jan 1, 1992

By I. J. Barker

This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferroalloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase AC electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become amore complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to obtain cheaper power from the organizations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of DC power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By Richard Ageton

SALT bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvinite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thick-ness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1936

By Henry M. Howe

MY attention has been drawn within a few days to a series of articles in Volume XVIII of the Engineering and Mining Journal, 1874, by Mr. J. A. Church, in which it is stated, among other

Jan 1, 1875

By Kasai H, Hibi T, Matsuishi S

Coal oil mixture (COM), a liquid fuel pro- duced by mixing together coal and heavy oil on the 50-50 basis, has been brought to a level of practical use in Japan, being actually employed by a oil fired system at Yokosuka Thermal Power Station of The Tokyo Electric Power Co., Inc. A COM Production Plant, built in Onahama which is located about 160 miles from Yokosuka, required COM to be transported by sea. Mitsubishi Heavy Industries, Ltd. therefore performed a series of studies to develop a spe- cialized COM carrier, the world's first of its kind. Long lasting high stability is of pri- mary importance to successful use of COM. Much have been done in the way of research on stability of COM in the static storage, and the mechanism of COM static: stability is almost completety known. On the other hand, the knowledge about the COM dynamic stability, such as the stability while being transported aboard the COM carrier at sea, is still limited at the moment. The motion of COM aboard the COM carrier and how COM would settle were studied by tests. A visualization test on the COM behavior under dynamic motion was also performed and the mechanism of COM dynamic stability was analysed. The tests showed that the ship rolling motion had @n effect of promoting the settling of coal content of COM in the cargo hold. And studies were also made to device a method for esti- mating the settling quantity of coal during sea Transportation.

Jan 1, 1987

By Dirk van Zyl

The world is consuming more and more electronic products every year. This has caused a dangerous explosion in electronic scrap (e-waste) containing toxic chemicals and heavy metals that cannot be disposed of or recycled safely. But this problem can be avoided. We are pressing leading electronic companies to change; to turn back the toxic tide of e-waste. Every year, hundreds of thousands of old computers and mobile phones are dumped in landfills or burned in smelters. Thousands more are exported, often illegally, from the Europe, US, Japan and other industrialized countries, to Asia. There, workers at scrap yards, some of whom are children, are exposed to a cocktail of toxic chemicals and poisons.

May 1, 2008