Search Documents

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983

By B. K. Chakrabarti

Modeling and a screening design of experiment (DOE) was performed with the process variables to identify the greatest effect of variables on the response quality in the dead burning of magnesite refractory in a rotary kiln. Among various interdependent variable factors, the design variables chosen were raw magnesite (RM) feed rate, kiln rotation time i,e, seconds per rotation(SPM) and burning zone temperature (BZT). The response variables chosen were exit gas temperature and density of dead burnt magnesite(DBM). ANOVA and normal plots were used to evaluate the effects.This work had enabled to correlate the BZT, RPM, RM feed with the exit gas temp and density of magnesite produced. The result opens up an avenue to look into the optimum region of operations within the ranges of variables considered in order to conserve energy and to minimize the exhaust gas temperature and to maximize the density of the DBM produced

Jan 1, 2015

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By W. H. Adams

I doubt if many of our engineers know of the existence of coalfields extending over hundreds of miles of territory bordering on and lying contiguous to the Rio Grande River in Mexico. Essential as these facts are to those contemplating the starting of industrial works along our frontier, 1 have not been able to learn that any surveys or examinations have been made of these deposits, arid I trust the preliminary and unofficial investigations lately made by myself may be found of interest, especially to those of our members whose experience has been with poor fuel, or in districts remote from railway facilities. While it is true that Northern Mexico is generally bare of charcoal-making timber, yet no greater mistake can be made than to condemn the light, quick-growing woods found in profusion, and which cannot be excelled in flame or heat-pruducing qualities for boilers, reverberatory furnaces, or hearths. No country could be surer of a full supply of wood if wise legislation in regard to irrigation and preservation of young timber were adopted and enforced, but the beneficiation of the low-grade ores of Mexico demands a more dense fuel for furnace work, and, fortunately for metallurgists, who will hereafter make this frontier a base of operations, there have been disclosed, near the surface, seemingly inexhaustible beds of semi-anthracite and bituminous coals. No extensive openings have as yet been made, and my own workings at the Cedral mines are all that can yet be said to prove the quantity and quality of the coal, other openings furnishing only corroborative evidence. Our location (one hundred and ten miles west of the Rio Grande River) is on the western line of the depository basin, as it has existed since the period of activity along the volcanic line. The region farther inland I have not examined, but the elevations, as a rule, are much greater, though from the nature of the formation, they are not necessarily barren ground. Beginning at the base of the Santa Rosa Mountains (location of the Cedral mines), we find very interesting breaks in the foot-hills, disclosing the stratified rocks from the volcanic centres to the valleys.

Jan 1, 1882

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By T. Haubold, K. Ortner, T. Jung, D. Roth-Fagaraseanu, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. Erosion of the blisk aerofoils in service reduces engine performance, and can result in short shop visit cycles. This significantly increases the life cycle cost of these components, particular when considering that eroded aerofoils can't be exchanged easily for blisks during refurbishment. Shop visit cycle times can be extended and maintenance costs can be reduced through the application of an effective protective coating. The ongoing development of an erosion resistant coating and deposition process suitable for coating complex blisk geometries is described here. The coating is a multilayered W /TiB2 system exhibiting superior erosion resistance compared to known single- and other multilayer concepts. A modified sputter process is used to enable coating even of blisk geometries with shadowed surface to competitive recurring cost.

Jan 1, 2006

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By T. G. Davies

The paper presents design equations for singly laterally loaded piles embedded in sand. These equations were obtained from a comprehensive nonlinear analysis of free and fixed head piles subjected to horizontal loads. The sand is modelled as an elastic-perfectly plastic material whose strength and stiffness are proportional to depth below ground level. The soil's response is described by means of a boundary element representation of the continuum while the pile itself is created as an elastic beam. Equations for the latter are derived directly from the Bernoulli-Euler theory and are coupled with those describing the non-linear soil response. The effects of bearing failure along the front, face of the pile, shear failure along its sides and tension failure at the back face are accounted for in the analysis. Simple equations are presented to describe both the elastic and inelastic responses. The only sol parameters required to use these equations are the angle of internal friction of the sand and a parameter characterizing the rate of increase of the sand's modulus with depth. The latter can be taken as equivalent to the modulus of subgrade reaction. The results of this analysis show that soil yielding is very significant at working load levels, resulting in substantial increase in bending moments and lateral deflection.

Jan 1, 2010

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By D. H. Lynch

Prompted by the need to conserve energy and reduce operating costs, Agrico Mining Company has made two significant improvements in the transportation of phosphate ore from the mine to the beneficiation plant. One improvement involves a change in a slurry pipeline system which substantially reduced pumping energy, and the other improvement is a major innovation for the phosphate mining industry which involves the transportation of the ore by railroad. This paper briefly describes these two projects.

Jan 1, 1981

By W. F. Lorch

Growing use of deionised water in surface coating techniques by w. F. LORCH Production engineers in the metal plating, paint, plastics-coating and printed circuit industries are increasingly aware of the cost of sub-standard or blemished items which have been poorly processed. An area where quality control can quickly produce higher efficiencies is in the choice of suitably purified water for making up solutions, for rinse baths and 'drag-out' baths, for cleansing lines and electrophoresis tasks, for maintaining electrolyte density and hence consistency, and for facilitating the recovery of valuable minerals. The author of this article examines the general problems of using nonpurified water, and shows how purified water has become accepted by the principal surface coating industries to improve processes and effect economies.

By Harry Verakis, Thomas Lobb

A great deal of information has been presented and published on the danger from flyrock created from blasting operations. The creation of flyrock is not specific to any one blasting operation. Flyrock is certainly not a stranger to blasting operations conducted in the mining industry and its effects are well known. Flyrock is among the leading causes of mine blasting injuries. Awareness and diligence is the message that must continue to be stressed and followed to reduce the potential for creating flyrock from blasting operations and to reduce the hazard it presents. A recent accident that resulted in a serious injury at a limestone mine in Pennsylvania bears witness to the ever-present danger of flyrock created from blasting operations.

Jan 1, 2007

By Adrian Brown

Over the last decade, a number of large slopes have been excavated in rock which contains families of joints or faults which dip steeply into the cut slope. Despite the absence of "adverse" structures, these slopes have exhibited alarming movement rates at very modest heights (as little as 100 meters) and slope angles (as little as 20º). Classical stability analysis suggests that such slopes should be unconditionally stable. This paper describes the toppling mechanism which has been found to be the cause of the observed movements and develops a general method for analysis of it. Simple cases are analyzed in order to provide charts which allow quick evaluation of the likelihood of this phenomenon occurring. The safety implications of such movements in slopes are also examined.

Jan 1, 1982

By R. G. Robins

The processing of gold bearing sulphide minerals which contain arsenopyrite and various complex arsenic sulphides results in arsenic containing emissions and effluents which are suspect in relation to clean air and clean water standards. Removal of arsenic from gaseous emissions is briefly reviewed. The use of lime to stabilise aqueous residues as either calcium arsenate or calcium arsenite is shown to be inadequate for long term disposal since both compounds are converted into calcium carbonate due to the influence of carbon dioxide in the atmosphere. Mixed calcium arsenate-phosphate residues are similarly unstable, but present better stability than the straight calcium compounds. Alternative disposal methods are reviewed whereby the arsenic is converted to more stable compounds, such as barium arsenate, titanium (IV) arsenate, and arsenic sulphide.

Jan 1, 1984