Search Documents

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By Scott G. Britton

Thin-seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges can be further amplified depending on such factors as labor unions, federal and state regulations and market characteristics. This article explores the turnaround situation occurring at Tanoma Mining Co. (TMC), a medium-sized, underground coal mining company in central Pennsylvania. The company has used a systematic approach of improving management controls and direction, labor relations and communications to improve its cash flow from negative to positive within a projected five-year span. An intensive upgrade-rebuild-replacement program for mining equipment and systems has also been established to support other management activities. Discussion Thin-seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors, without the advantages of moving volume per foot of extracted material. To stay at economic parity with others requires additional creativity within the management team to extract higher productivity gains from the existing workforce and mining systems. The Tanoma operation is a deep mine in Indiana County, PA, about one hour northeast of Pittsburgh. Coal is extracted from the Lower Kittanning "B" seam. It lies about 91 m (300 ft) below the surface and averages 0.9 m (I ft) in height. Continuous mining units using mobile bridge conveyors or shuttle cars

Jan 1, 1991

By Bruce A. Kennedy

Lufthansa flight 497 roared down the runway and climbed rapidly through the early morning mist hanging over Pudahuel airport and the city of Santiago, Chile, into the brilliant sunlight above the clouds. As the plane banked onto course for Lima, Peru, we got what was possibly our last look at the beautiful snowclad mountains that ring Santiago. To the northeast was the massive hump of Aconcagua, the highest mountain in the Southern Hemisphere, wreathed in clouds and virtually looming over Rio Blanco, the new mine put into production by Cerro de Pasco just one short year before. Almost a thousand miles to the north lay the massive open pits of Chuquicamata and Exotica, and a little closer to Santiago the El Salvador mine. Behind to the southeast, clinging to the steep slopes of the Andes, was the large and awe-inspiring El Teniente mine at Braden. These mines, once the bastions of such companies as Anaconda and Kennecott, had a new owner-the Government of Chile. On the plane were a number of people who had spent a large part of their lives in Chile operating these mines and plants, and who now were suddenly faced with the necessity of starting new lives somewhere else. To them, this was their last look at the country which not too long ago was their home, a bittersweet moment of reminiscence and a time for questioning what the future held.

Jan 1, 1971

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

By N. Vayenas

Modern mines possess a wide variety of capital intensive equipment. Equipment failures and the associated down time contribute significantly to the overall maintenance, operating and production costs of a mine. Reliability investigations are becoming a standard practice, as the equipment becomes more complicated and the effective use of resources is critical for achieving higher productivity and mine safety. In view of the recent global initiative for sustainable development in the mineral industries, reliability of capital intensive machinery should be considered as a key indicator for sustainable development and growth. This paper discusses the application of equipment reliability as a sustainability indicator and proposes a methodology for its practical use. Reliability of equipment systems is useful for product life cycle assessment, mine performance measurement and evaluation.

Jan 1, 2007

By João Felipe Costa, Jair Carlos Koppe, André C. Zingano

Abstract - Traditional mine planning based on block models built with interpolation techniques such as kriging does not take into account the uncertainty associated with the estimates. These models are inadequate for short-range mine planning. In contrast, conditionally simulated models reproduce the actual variability (histogram) and spatial continuity (variogram) of the attributes of interest. Conditional simulation can be used to address the problem of measuring the uncertainty associated with an estimate. This paper outlines how the sequential Gaussian conditional simulation algorithm can be used to assess uncertainty of grade estimates and also illustrates how simulated models can be incorporated into mine planning and scheduling. A case study demonstrates the efficiency of the method in assessing risk associated with geological and engineering variables.

Jan 1, 2000

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By Y. Guan

The adsorption of zinc species onto silica in ammonical solutions has been studied. Adsorption isotherms reveal that increasing adsorption occurs as the solution pH is made more alkaline. Fr-IR spectroscopy revealed that the adsorbed species is a zinc ammine complex.

Jan 1, 1993

By Michel Aubertin

Using mine wastes as backfilling material for underground stopes has been a common practice for more than 60 years. Waste rock and tailings are used as filling materials because they are available at a reasonable cost to support the rock walls. Backfilling is also very advantageous because it reduces the amount of mine waste disposal on the surface. In underground mines, the backfill must first ensure stability of the opening, while increasing recovery of ore and minimising dilution. It is thus critical to accurately evaluate the pressures exerted on the walls and on the barricades placed near the base of the stope. In this presentation, existing solutions for evaluating the stresses on stope walls and barricades are briefly reviewed. The authors then present recently developed analytical solutions that take into account the stress transfer from the backfill to the walls in the stope and access drift. The stress state solution, which is based on arching theory, considers the influence of the stope geometry and barricade position within the drift. The method gives the pressure generated by partly or fully submerged backfill. The solutions apply shortly after backfill deposition, when the effect of pore water pressure cannot be neglected, and also for long term conditions under a fully drained state. Experimental testing and numerical modelling results are used to validate the proposed equations. Both numerical and analytical results show that the total pressure on barricades can be significantly increased by water pressure, while the effective stress is decreased (compared to dry or drained conditions). A discussion follows on the implications of the results for backfill applications.

Nov 1, 2008

By U. Thorley

Management of mine and tailings reclamation activities by surface mining oil sands operations in Alberta, Canada is experiencing increased national and international attention. Of particular concern is the ability of existing mines to execute and fund reclamation activities. Concern stems from a lack of demonstrated tailings reclamation technologies, perceptions of a poor track-record of reclamation activity by industry, and a lack of transparency with respect to the potential cost of reclamation activities relative to the monies secured in Alberta?s Environmental Protection Security Fund (EPSF). Limited information is publicly available regarding reclamation costs and technologies. Available data typically comes from disparate sources. This paper examines the expected costs of oil sands reclamation activities through a study of corporate Asset Retirement Obligation (ARO) liabilities, the Province of Alberta?sEPSF, and published data relating to reclamation costs.Issues relating to current liability funding are introduced.

Jan 1, 2011

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971