Search Documents

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By T. N. Rushton

Rate minima are encountered in the reduction of magnetite with hydrogen. In a certain temperature zone, the reaction rate decreases with rise in temperature. This is inexplicable by classical kinetic theories; neither is a transition in reduction mechanism suitable for interpreting the observed behavior, This anomaly can be fully explained by hypothesizing two species of chemisorbed hydrogen with different adsorption coefficients and activation energies for adsorption. Competition between two energetic states of adsorption occurs with temperature rise, with the low energy state predominating below the anomalous temperature zone and the high energy state above it. The presence of two possible adsorption sites appears to be characteristic for oxidic adsorbents.

Jan 1, 1968

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K J. F Logan, P W. Leaman, B A. Tucker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Nam San copper-gold deposit was discovered in 2011 and is a likely blind extension of the Permian age Phu Kham structurally deformed porphyry/skarn copper-gold deposit.The Nam San mineralisation is hosted within a dominantly sericite altered schist unit located to the north of the current Phu Kham open pit operation and is overthrust by an allochthonous barren cover sequence of limestone, granite and sandstone. Reinterpretation of the Phu Kham geology developed the concept of a possible telescoped porphyry copper-gold system at depth. Initial drilling intersected remobilised copper mineralisation in a basal conglomerate, confirming the concept. A reconnaissance vector array induced polarisation (IP) survey identified a deep chargeability anomaly from which a drilling target was developed from 3D inversion modelling of a detailed follow up dipole-pole-dipole anomaly. Drilling of the chargeability anomaly intersected the blind Nam San copper-gold mineralisation beneath the thrusted cover sequence.The key discovery parameters are the result of an integrated exploration program that included reinterpretation of the local stratigraphy, which developed the concept of a deep blind orebody, IP surveys capable of penetrating through the barren cover and a commitment to a deep directional drilling program to test these concepts and targets. The inferred resource remains open at depth, and further assessment will most likely be through underground development.CITATION:Leaman, P W, Tucker, B A and Logan, K J F, 2015. The discovery of the Nam San copper-gold deposit, Phu Kham, Laos, in Proceedings PACRIM 2015 Congress, pp 515–520 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By Joseph J. Feiler

Fires in underground coal mines are persistent problems anywhere in the world that coal is mined. Coal fires pose safety and health hazards in the form of mine subsidence, loss of energy reserves, destruction of property and surface improvements, and air pollution. In 1995, the US Bureau of Mines (US-BM), in cooperation with the Colorado Division of Minerals and Geology (CDMG),entered into a contract with Goodson & Associates Inc. (GAI) to design and field test the effectiveness of a new foamed grout technology called ThermoCell. GAI is a Lakewood, CO geotechnical and mining reclamation engineering firm. The company developed ThermoCell to control and extinguish underground coal fires. The viability of the special grout and the technology of application were established during a full-scale field demonstration at the abandoned IHI Coal Mine fire, near Rifle, CO. Following acquisition of additional funding by CDMG in 1999, Goodson returned to the site in April to continue the grouting to fully extinguish the IHI fire.

Jan 1, 2000

By Chand F

The silver deposits of Rockvale near Armidale, N.S.W., occur in fissure veins in epi-Permian granite. The ore is fine grained, mineralogically complex, and contains twenty-seven different minerals including eleven silver minerals. The ore is characterized by a unique multiple unmixing from a sphalerite solvent. The following minerals have exsolved from solid solution in sphalerite: pyrrhotite, chalcopyrite, cubanite I, cubanite II (chalcopyrrhotite), valleriite, "brown" stannite, "olive" stannite, argentian tetrahedrite, pyrargyrite, and an unknown grey-white mineral. Several of these minerals derive from a second-stage unmixing, the immediate solvents of which are the products of earlier exsolutions.INTRODUCTIONSmall silver-rich base metal deposits occur at several localities near Armidale in the New England district of New South Wales. Chief among these are the Tulloch Mine and the Rockvale Mine at Rockvale, 27 miles SE. of Armidale, and the Tait's Gulley deposits some 15 miles NE. of Armidale.At Rockvale (Kenny, 1928), irregular lenses of lode material, principally quartz and calcite, occur along a zone of shearing in biotite granite and altered sediments. The orebodies had a maximum width of 6 ft but averaged 2 ft 6 in. The largest lens was 150 ft long and 50 ft high. The Rockvale deposits were worked for both arsenic and silver; 2,897 tons of arsenic were produced but no figures are available forsilver.Little is known of the Tait's Gulley deposits which occur in folded arenites containing small but rich veins of pyrargyrite with base metal sulphides.The sediments in these localities are possibly Silurian.

Jan 1, 1962

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By H. Lowers, P. Hageman, S. Diehl, D. Fey

Understanding relationships between mineralogy, texture, microstructural features, and element distribution and residence in minerals, is critical for accurate modeling of mineral weathering in waste-rock piles. The morphology of minerals and deformation structures, such as veins and faults, are important factors that control: (1) fluid access to the mineral surface to initiate dissolution, (2) the distribution of trace elements, and (3) formation of secondary minerals. We characterized the mineralogy, textures, and chemical properties of waste-rock material at three sites at scales ranging from outcrop to micrometer scale. A comprehensive hand-sample to thin-section scale methodology utilizing light microscopy, scanning electron microscopy, electron microprobe, and laser ablation ICP-MS was used to thoroughly characterize the waste-rock material.

Jan 1, 2007

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006

By Steven W. Wilson, Brigitte Lacouture, Nichola A. McKay

"The Aqqaluk deposit is a lead-zinc ore body that lies immediately north of the Main Pit at Teck Cominco’s Red Dog Mine in Alaska. It is scheduled to begin production in 2011 or 2012. A project team was formed in late 2004 to plan and implement an ore characterisation and metallurgical evaluation on the Aqqaluk ore. The main objective of this program was to facilitate the transition from Main Pit to Aqqaluk ore in the Red Dog concentrator. The program will develop a detailed, spatially-oriented characterisation of the Aqqaluk deposit attributes including lithology, ore geochemistry, bulk mineralogy, ore texture, as well as evaluating the metallurgical characteristics of ore hardness, process water geochemistry, bench-scale floatability and mineral liberation in ground feed, concentrate and tails. Developing correlations between the metallurgical response and the ore characterisation data is key to the emerging science of geometallurgy. This on-going program is a technical due diligence study that aims to reduce the risk associated with processing a new ore and to provide predictive information for mining and stockpile preparation.The test work to date has focused on characterising the five ore zones currently identified in the Aqqaluk deposit, namely: Siliceous (sub-divided to High Zn:Fe and Low Zn:Fe), Vein, Median Plate and Baritic ores. It identified a number of challenges associated with surface oxidation, or weathering, of the core samples and outlined a program for future sample collection and storage. Metallurgical testing evaluated ore hardness by a variety of methods. Preliminary floatability studies have been completed and some initial links have been established between the ore characteristics and the flotation response. Soluble mineral weathering products, the relative abundance of pyrite and marcasite and the iron content in the sphalerite grains have all shown a correlation to mineral recovery.As new core is received, both the ore characterisation and the metallurgical testing will be continued with a view to strengthen the existing correlations and develop new links."

Jan 1, 2007

By D. F. Hewett

CONTENTS PAGE Introduction 1 Geologic features of eastern Oregon 2 Geology of the Sumpter quadrangle 2 Rocks older than the ore deposits 3 Rocks younger than the ore deposits 8 Lodes of the Sumpter quadrangle 8 Areal distribution 8 Geologic distribution 9 Major features of the veins 9 Mineralogy and texture of the veins 13 Ore deposits zonally disposed around the Bald Mountain batholith . . . . 13 Summary of mineralogy and texture 32 Zonal relations 33 Ore deposits zonally disposed around Greenhorn Mountain batholith . . . 36 Zonal relations 37 Relation of textural features to zonal arrangement of veins 37 Summary of zonal relations 38 Comparison with similar districts 39 Outlook for the district 40 INTRODUCTION IN an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

Differentiation of a basaltic (?) magma occurred in an active volcanic area during the late Miocene and Pliocene, and a change in the general mode of extrusion from fissure flow for the basalt to explosion for the andesite reflects an accompanying increasing magmatic viscosity. A caldera formed after the flow phase was completed and was filled with coarse agglomerate, much of which has a fused appearance. After an erosion interval its shape was modified and it became gradually deeper as repeated explosions from growing andesitic volcanoes caused large quantities of pyroclastic material to be deposited. At the close of this phase the floor abruptly collapsed when a, large block of the underlying crust was engulfed. The incompetent pyroclastics filling the caldera steepened in dip and the ensuing fractures were filled by the rising magma as dykes and sills and a chonolith formed below the caldera at a shallow depth. The ensuing activity reveals a further stage in differentiation and biotite is an important new ferromagnesian to be observed in the new rocks.Fracturing of the surrounding basalts was most intense in the rocks forming the periphery of the caldera where steeply and flatly dipping faults resulted from increasing horizontal pressure directed towards the caldera.Further differentiation resulted in the increased crystallization of orthoclase felspar, as evidenced by the numerous intrusives of trachy andesitic composition. Magmatic freezing caused mineralizers to accumulate at the top of the chonolith. These eventually escaped and auriferous pyrites, tellurides, quartz, and calcite were deposited in the surrounding rocks.The flatly dipping fractures are the most important and can be expected at various depths in a zone about 4,000 ft wide surrounding the caldera. Latest movement along these was controlled by magmatic consolidation rather than the shape of the caldera. Some flat faults were able to remain open during mineralization and acted as a feeder for the shallower fractures, thus limiting the depths to which the steeper dipping fractures were mineralized with the possible exception of one particular Nw.-striking lode (the Crown-Crescent).INTRODUCTIONThe gold deposits of the Tavua district were discovered in 1932 and from 1935 to June, 1961, 1,985,041 fine ounces of gold were produced from 4,202,504 tons of ore. Of the original three producers, only the Emperor remains active in the...

Jan 1, 1962

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015