Search Documents

By Donald Jonson

Stockholm’s Northern Link, currently Europe’s largest urban road tunnel project, will be about 5 km long from west to east. Running through two separate, mostly parallel tunnels, each with 2-4 lanes, the complex will include numerous entries and exits, as well as a major branch to the north. The total length of tunnel will be 11 km, of which 9 km will be in rock. Over million m3 of rock will be blasted. The Northern Link will open to traffic in 2015. After a 10-year stop to deal with environmental questions regarding Ekoparken, Stockholm’s unique “national city park”, the Northern Link project in the Swedish capital was restarted in the autumn of 2006, with the construction of five works-access tunnels.

Jan 1, 2009

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By L. H. Smith, D. S. Taylor

"AbstractSherritt has been applying hydraulic drives to concentrator equipment since 1967. The initial application was made on a bank of 5- by 5-in. slurry pumps. This has now been extended to all slurry pumps requiring less than 40 hp and several conveyors which require variable-speed or low-speed/high-torque characteristics. The pump motors are directly connected through a flexible coupling, whereas the conveyor systems are directly mounted onto the head-pulley shaft extension.The different applications and design concepts will be described, with outlines of the operating and maintenance advantages and disadvantages and costs. The paper also outlines future possible applications, together with the limiting conditions, of such systems.IntroductionSHERRITT GORDON MINES LIMITED has been operating a mining division in Northern Manitoba for almost 50 years. The original mining operation was at Sherridon, Manitoba and was a copper-zinc producer. This mine was exhausted in 1948 and the mining plant was moved north to its present location at Lynn Lake, Manitoba. The Lynn Lake Mine is a nickel-copper producer. Since 1960, two new mines have been discovered and brought into production in the general vicinity of Lynn Lake. The first of these was the Fox Mine, a copper-zinc property operating at 3,000 tons per day from an underground operation. This mine started production in May 1970."

Jan 1, 1977

By M. Leroux, P. Lacombe, S. R. Rao, J. Y. Kim, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

"Laboratory investigations on two complex ores, the A1 zone ore from Les Mines Selbaie and the Lyon Lake ore from Mattabi Mines Ltd. (Division of Noranda Minerals), have been carried out to determine some of the main variables in collectorless flotation. In particular, the effect of pulp potential (controlled by gas composition), conditioning time, pH and grinding media have been studied.Chalcopyrite showed the greatest response to collectorless flotation among the four major sulphide minerals present, followed by galena. Flotation of sphalerite was variable from minimal to important depending on the mineralogy and the pre-treatment performed. Appreciable silver recovery was achieved collectorlessly for the Lyon Lake ore while it could not be achieved for the A1 zone ore of Les Mines Selbaie. It appears that the difference between the two ores is related to silver's predominance as tetrahydrite in the Lyon Lake ore while it is as argentite and native silver in the A1 zone ore.The response of the ores to collectorless flotation is strongly dependent on the pulp potential, Ep, and pH. Using different gas compositions and different conditioning times it was found that collectorless flotation occurs when Ep is +195 to +295 mv (vs SHE). The actual on-set potential for collectorless flotation is dependent on the ore. A too high potential or prolonged oxidation leads to a decrease in selectivity. Some other factors were examined, notably the effect of pH and the type of grinding media on the selectivity achieved in the laboratory.Preliminary results from a plant trial at Mattabi Mines Ltd. confirmed that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Collectorless flotation was not attempted at Les Mines Selbaie. However, examination of the distribution of collector between the different addition points in the copper circuit suggests that it may be present."

Jan 1, 1990

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1' section with the depth of 180 m and GS2-GS2' section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d'or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l'intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l'analyse de la stabilité au moyen de la méthode d'équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1' avec la profondeur de 180 m et la section de GS2-GS2' avec la profondeur de 150 m dans l'aire d'étude, nous mîmes l'hauteur du gradin à 10 m et 15 m, et l'angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d'examen a indiqué que il pourrait être propre de mettre l'hauteur du gradin à 10m et l'angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1' mit der Tiefe von 180 m und GS2-GS2' mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By Lo-Sun Jen

Introduction ? Canada is one of the largest miners and explorers in the world and is a world leader in the production and export of many key mineral commodities ? Canada has a stable political regime and a competitive investment and business climate ? Canada is endowed with mineral resources, advanced technology and management know-how ? Canadian stock exchanges are the world?s leading centres for raising equity financing for exploration and mining projects anywhere on the globe As with some other countries, Canada has experienced a recent decline in major mining developments

May 1, 2002

By W. R. Bruce, G. W. Hodgson, K. A. Clark

"IntroductionANY PLANT processing mined Athabaska oil •sand for the recovery of oil produces, as a waste material, about one ton of sand for every barrel of oil recovered. A disposal problem of major proportions is thus indicated. For a 100,000-barrel per day plant, provision must be made for moving .about 4,000 tons of sand per hour on a continuous basis to a tailings dump at least several thousand feet removed from the plant site.Of the many known ways of conveying solids on .a large scale, the hydraulic pipeline transfer method is becoming increasingly important because of convenience and economy of operation. It has been in use for many years in mill operations at metalliferrous mines for the disposal of tailings and as such was a natural outgrowth of •hydraulic sluicing (3). Pipeline transportation of mill concentrates has been adopted recently ( 1), wherein high-density solids are moved several miles by hydraulic pipeline. The flotation power of the water suspending the solids may be increased 'by addition of magnetite for the handling of ore in pipelines (8). Low-density solids such as coal have received considerable study for low-cost pipe-lining (2) and a successful operation with coal has been carried out in England with indications of considerable savings over other methods of transportation (9). Dredge operations are based on pipeline transportation for the dredged sol-ids, and the scale of pipelining there .has involved pipe sizes as large as 32-inch (6). However, the tendency has been to regard the pumping of solids in water merely as a simple method of transportation and little consideration has been given in the published literature to study of the most economical modes of operating .a pipeline."

Jan 1, 1952

By T. McKeon

Gravity separators are commonly used in multistage cleaning and scavenging circuits to improve the quality and/or recovery of the final concentrate. Unfortunately, studies suggest that many industrial plants are poorly designed in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiencies of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Jan 1, 2005

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON' discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By M. Berger

The ‘Metallurgical Operations’ Department of Grinaker-LTA Process Engineering (GLTA) currently undertakes then primary mining as well as the re-deposition of tailings forTicor South Africa (Ticor) at their Hillendale mine near Empangeni, KwaZulu-Natal, South Africa. The mining plant, which was designed by GLTA on a Build, Own, Operate and Transfer (BOOT) basis, is capable of mining 780 000 tons per month of ROM material which is then pumped to the Primary Wet Plant for treatment by Ticor. Hydraulic mining via high pressure water cannons and subsequent transfer of the heavy mineral slurry at an RD of between 1.35 and 1.48, has never before been undertaken successfully at this level of production on an in situ reserve. The presentation will take the form of a case study in which the unique site operating conditions will be detailed and discussed, as will the innovative process and engineering solutions employed by GLTA to overcome the engineering and production challenges encountered. In order to protect the intellectual property involved in this operation, this paper is fairly general in nature, and attempts merely to provide the reader with a broad perspective understanding of the operation, and some of the difficulties encountered during the early stages of production.

Jan 1, 2003

By M. S. Seehra, V. S. Babu, L. Farinash

"The diesel particulate matter (DPM), a constituent of the diesel engine exhausts, is known to be a potential carcinogen. 1- 3 Consequently, suitable methods to control/eliminate DPM have ·been under investigation in recent years. The DPM can be controlled by using fibrous ceramic traps. However, clogging of traps by DPM requires the impractical periodic trap replacement. Following the recent work by Garner and Dent,4,5 we are investigating the in situ use of microwaves to regenerate the ceramic traps, thereby eliminating the trap replacement step in this process. The use of microwaves instead of conventional heating for trap regeneration has the advantage of selective heating of the DPM instead of the trap, if the trap absorbs insignificant microwave power relative to the DPM. Also, the oxidation characteristics of the DPM are needed to understand fully this regeneration process.The rate of energy absorption P per unit volume of a sample is given byP = wE"" |Eo|2 • (1 )where w is the angular frequency, |E0|2 is the intensity of the microwave radiation, and E” is the imaginary part of the dielectric constant (E = E’ + iE”) . Thus measurements of E11 for DPM and ceramic trap material are needed to determine their capacities for microwave absorption. In this paper, we report these measurements carried out at · a frequency of 8.7 GHz. Following microwave absorption, the DPM is expected to oxidize. The oxidation characteristics of the DPM have been investigated using Fourier transform infrared (FTIR) spectroscopy of the evolved gases CO2 and CO and using thermogravimetric analysis (TGA). Finally, some information on the structure of carbon in DPM has emerged from the analysis of its x-ray diffraction spectra. Results of these experiments are reported in the following pages."

Dec 1, 1996

By Rivera Jose Antonio Ore

Top Submerged Lance (TSL) smelting technology is currently used in a wide range of applications in the non ferrous and waste product treatment industries. The use of TSL technology for tin concentrates smelting has been successfully applied at the Minsur Tin Smelter and Refinery at Pisco, Perú. The process is based on the air-cooled top entry submerged Sirosmelt lance, developed by Dr. John Floyd at the CSIRO division of Mineral and Process Engineering in the 1970?s. Advantages of the process include flexibility to operate the lance, main burner of the Sirosmelt furnace, with different levels of combustion stoichiometry which allows us to get from highly reducing to highly oxydising atmospheres in the smelting reactor according to the type of feed we are processing, ability to utilize cheap energy sources such as natural gas, low capital cost and an environmentally friendly operation. This presentation summarises the application of the Submerged Sirosmelt technology for smelting tin concentrates and a variety of tin containing materials like iron dross, copper dross, tin residues, low tin/antimony slags by applying recent metallurgical developments at the Minsur smelter. The impact of new feed conditions and level of impurities on reactor performance with features of process and operation control are described. As a result of these recent advances in tin smelting using TSL technology, the Minsur Tin Smelter and Refinery improved its overall tin recovery, substantially reduced tin inventories and became the second largest tin smelter in the world, currently producing more than 40,000 metric tones of refined tin per year.

Jan 1, 2006

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014

By C. Chingwaru, W. Chingwaru, J. Vidmar

"Zimbabwe is endowed with rich deposits of minerals such as diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching has been implemented as an efficient and low-cost method to extract metals such as copper, cobalt, and gold from sulphide and/or ironcontaining ores and mineral concentrates in a number of countries around the globe. Zimbabwe, despite being a world leader in mineral wealth, has gone through years of economic stagnation which have brought with them energy shortages. Bioleaching is an innovative way to recover minerals from ores using relatively low-capital-cost and non-polluting technology. Principally, iron- and sulphur-oxidizing bacteria can be used to oxidize iron and sulphide to ferric iron and sulphuric acid, respectively, and the ferric iron oxidizes the insoluble metal sulphides to soluble metal sulphates that can be readily recovered from solution. Although some minerals such as gold are inert to biological reactions, they can be liberated using bacteria that act on certain types of ores and other minerals that co-occur with these minerals. The geology of the mineralized areas in Zimbabwe, rich in chalcopyrite / pyrite, allows a number of microorganisms to be used for the extraction of minerals by bio-oxidation. This paper reviews the potential of bioleaching in the country. IntroductionZimbabwe has rich deposits of minerals including diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching is defined as the use of microorganisms to facilitate the extraction of metals from sulphide or iron-containing ores or concentrates (Rawlings, 2004, 1997). Bioleaching has been shown to be an efficient (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004) and low-cost (Schippers et al., 2010) method to extract minerals in many countries around the globe. For example, aerobic Fe(II)- and sulphur-oxidizing bacteria have been shown to be up to two orders of magnitude more efficient in the oxidation of pyrite than the chemical processes (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004). Additionally, bioleaching can be used to extract minerals from low-grade ores, sulphidic waste rock dumps, and tailings efficiently (Schippers et al., 2010)."

Jan 1, 2017

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

This brief resume of the events transpiring in Mexico, culled from the daily New York newspapers since the last Bulletin went to press, does not show any degree of improvement in the situation. MEXICO SEEKS TO AVOID BLAME FOR BANDIT RAIDS All foreign passengers leaving Nogales for Mexico on the Southern Pacific or Mexico Railroad. whose business would take them through territory occupied by the Yaqui Indians or Mexican bandits were requested by Mexican Consul Emilio Tamez to sign a statement that they relieve the Mexican government of responsi-bility for anything which might happen to them while in that part of Mexico. The Mexican consul stated, says the N. Y. Tribune, that this was by order of Mexican Ambassador Ignacio Bon ill as, at Washington. When the State Department was advised of this activity Secretary Phillips, in a message to the consulate at Tampico, according to the N. Y. Tribune, asserted that "compliance with the waiver requirement will not interfere with the relation existing between the United States and its citizens and that Americans so complying will in no way lose the protection of this government."

Jan 11, 1919