Search Documents

By O Ostrovski

Direct iron smelting reduction has been examined using a modified 50 kg induction furnace. The furnace was equipped with continuous raw material feeding, a top oxygen lance, argon bottom bubbling, and sensors for measurement of gas and bath temperatures, gas composition and other parameters. In the base case, iron ore was charged at the rate of 1.5 kg/h, coke flowrate was adjusted to maintain a char fraction in the slag at 30 wt per cent, the oxygen flowrate was 100 Nl/min and the post-combustion ratio (PCR) was 60 per cent. The PCR was varied from 45 to 75 per cent by changing the lance height relative to the bath surface. Smelting reduction of Whaleback iron ore was investigated at different post-combustion ratios and iron ore feedrates using coke and coals with different volatile matter. The rate of iron oxide reduction increased with increasing iron oxide concentration in the slag, with a slight deviation from a linear function. The post-combustion ratio affected iron ore reduction and partitioning of elements between phases in the smelting reduction furnace. The high volatile coal investigated was found to be unsuitable for iron smelting reduction in the laboratory furnace.

Jan 1, 2000

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

By Steve Kral

The power industry throughout the world is in the midst of a significant transition that will result in a major restructuring. Deregulation of utilities in the United States is continuing, resulting in increased competition among power providers. The traditional ways that electric power is globally bought, sold and delivered will also change. However, according to the Department of Energy's (DOE) Pat Godley, one thing is clear: "Those who provide the power during the 21 st century will be those who are willing to change - those who are willing to accept new ways of doing business and willing to employ new technologies." Godley is assistant secretary of fossil energy with DOE. Her comments came during the opening remarks at the Fourth Annual Clean Coal Technology Conference, held in Denver, CO, Sept. 5-8, 1995. The conference was sponsored by DOE and the Center of Energy and Economic Development. Under the theme "Global Opportunity," more than 300 coal and utility executives spent three days discussing the new face of the electric-power industry throughout the world and the new, mostly clean coal technologies (CCT) that will be available to power providers.

Jan 1, 1995

By Brandon H. Grove

The Zistersdorf field, near Vienna, continues to be Austria's only producing area. During the year the field was slightly extended by Rohol Gewinnungs A.G. in its Rag 2, which in April came in for an initial 120 tons daily through an 8-mm. (0.315-in.) bean, from the twelfth Sarmat sand at 1447 m. (4747 ft.). The amount of fluid produced by this well has remained essentially constant, but after the first several months water appeared and increased to some 50 per cent of the total. TWO subsequent extension wells, Rag 3 and Rag 5, northeast and west of Rag 2, found only water-bearing sands, and drilled through the main fault and into the Flysch at 1683 and 1401 m. (5522 and 4596 ft.), respectively. At the close of the year preparations were under way to deviate both wells away from the fault to test still deeper sands. Within the previously proven area of the field Erdolproduction's Gosting VII came in flowing a maximum of 440 tons daily, the highest individual production yet recorded. This company's Gosting VIII also yielded an initial production of 20 tons daily, and its Gosting XI, drilling

Jan 1, 1938

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By A. L. Muler

Since 1956, when Broadbent and Callcott 1 proposed to analyze breakage processes by matrix methods, several authors and their co-workers have proposed various models of grinding that, in principle, could lead to fully automated grinding circuits. In particular, Meloy and Gaudin2, Gardner and Austin3, Kelsall and Reid4, Neloy and Bergstrom5, Callcott and Lynch 6, and Draper and Lynch have, by either computer simulation or by experimental data, or by a combination of the two, verified that comminution is reasonably well described by at least two functions: a selection function and a breakage function. The stage concept proposed by Callcott and Lynch6 requires that a classification matrix be included to completely describe breakage in an open circuit rod mill. The purpose of this work, portions of which are herein described, is to accumulate sufficient information on the breakage characteristics of quartz and magnetite in an open circuit rod mill, so that several of the theoretical and experimental approaches proposed in the literature can be compared with each other. Data is being gathered to compare the experimental method used by Kelsall and paid against the stage approach of Callcott and Lynch.

Jan 1, 1968

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

By M. L. Free

Several studies of the fluorite/oleate flotation system have shown that under certain conditions calcium dioleate is formed at or transported to the fluorite surface. Adsorption of significant amounts of calcium dioleate is generally observed above oleate concentrations of -6 -5 between 4 x 10 and 4 x 10 M, yet little explanation of the onset of calcium dioleate adsorption is provided. In this study in-situ and ex-situ FTIR/IRS experiments have been performed in connection with thermodynamic solution phase analysis to better understand oleate adsorption as well as the onset of calcium dioleate formation. Results from this study are analyzed and compared to industrial practice.

Jan 1, 1995

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

By-products are of greater importance in lead and zinc mining than in any of the other major base metals. While I think most mining people would accept that statement, you would probably get some widely varying estimates when attempting to quantify the value of by-products in lead and zinc mining. We are now able to do this with our lead-zinc mine cost model. This model was originally developed as a zinc mine cost model to help us forecast long-term zinc supply and price as part of a study we completed in late 1979 entitled "Zinc - The Next Decade". Before demonstrating the importance of by-product revenue to lead- zinc mines, let me first explain how the cost model was constructed. I will discuss the model as it was originally constructed - as a zinc mine cost model. It has subsequently been expanded to include lead only mines and now can Be run either as a zinc or a lead mine cost model.

Jan 1, 1980

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By AIME AIME

CONCIDENT with what promises to be a record-breaking year of activity in the world's greatest iron-ore district is the announcement of plans to hold the regional meeting of the American Institute of Mining & Metallurgical Engineers at Duluth, Aug. 12 to 15 in¬clusive. More than 25 open-pit mines will be in operation in Minnesota's great iron-ore district this year, affording to those attending the convention an unusual op¬portunity of viewing practically side by side the interesting activities of power-shovel operations, railway haulage, truck haulage, conveyor-belt haulage, tower-excavator operations, iron-ore concentration, and underground mining. The ore can be followed from the mines to washing and concentrating plants and to the docks and lake carriers on Lake Superior, where an average of one boat of 10,000 tons' capacity will be loaded and depart every 15 minutes, day and night, during the 1941 shipping season.

Jan 1, 1941

By W. N. Hamilton

"Evaporites abound in the Western Canada sedimentary basin, recurring throughout the stratigraphic column and widely scattered over the basin region. Alberta, situated centrally over the basin, includes many of the evaporites within its borders, but only a few have the right geological conditions to form potential economic deposits of salt or gypsum. These include the Middle Devonian Elk Point Group and related evaporites, Upper Devonian Wabamun Group-Palliser Formation evaporites, and evaporites of the 'Triassic Charlie Lake and Whitehorse formations.Salt deposits underlie almost half of Alberta. The major deposits belong to the Elk Point Group, which includes thick salt units in the Lotsberg, Cold Lake and Prairie Evaporite formations. Another, younger salt deposit in the Wabamun Group has only local distribution. Elk Point salts have a maximum aggregate thickness of 430 m in east-central Alberta. The deposits deepen southwestward across the province, from minimum depths of210 m at Fort McMurray to 1820 m at Edmonton.The thickest, most extensive salt deposits are the upper Lotsberg and Prairie Evaporite salts. Both have excellent development potential. The upper Lotsberg is up to 150 m thick, consists of clear, very coarse crystalline halite with only minor impurities, and has a notable lack of non-salt strata in its succession. Analytical data for the Lotsberg Salt show extraordinary chemical purity. Prairie Evaporite Salt differs lithologically from the Lotsberg in having a significant non-salt component. The deposit is up to 200 m thick and consists of medium crystalline halite, brownish coloured and cloudy as a result of finely dispersed impurities. The main impurities-shale, anhydrite and dolomite-are most prevalent as interbeds in the salt succession, ranging from very thin laminae to beds several metres thick. Although of lesser purity, the Prairie Evaporite Salt is shallower, thicker and more extensive than the Lotsberg and the salt quality is quite acceptable for most industrial uses."

Jan 1, 1982

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

Like it or not, CPD is upon us. As from 1 January 2006, all registered engineering professionals, i.e. professional engineers, professional engineering technologists, professional certificated engineers and professional engineering technicians, were required to undertake CPD in order to keep their professional registration current. The rules regarding CPD have been gazetted under Government Gazette No. 28328, Board Notice 131 on 23 December 2005, and they also appear on the ECSA website?www.ecsa.co.za. For the convenience of our members they are reproduced in full in this issue of the SAIMM Journal.

Jan 1, 2006

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By William P. Blake

THE importance to the growing steel industry of the United States of a domestic supply of ferro-manganese or "spiegel" of a high grade, induces me to bring to your notice some details of the method by which a superior article is produced in the Austro-Hungarian Empire. At Reschitza, Hungary, and probably at Laibach also (the Krainische Industrie Gesellschaft), ferro-manganese is made in a blast-furnace, with charcoal as fuel, and limestone as the flux. The ore is a ferruginous mixture, containing about 37 per cent. of sesquioxide of manganese. It is silicious, and somewhat resembles, in its appearance, the manganese ore from Red Island, in the Bay of San Francisco, California. It contains about 29 per cent. of silica and some alumina, shown by the subjoined analysis

Jan 1, 1876

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

By Toomey P. T

In many open cut coal mines, rivers and large creeks can cause planning and operating difficulties, both in the terms of the more obvious location of the current watercourse, but, and sometimes more importantly, past meandering of the watercourse. Prevent and past flow regimes may have deposited large alluvial sequences within the current mining areas. The presence of groundwater within the alluvium further complicates the planning and operating practices.A situation exists at Saraji Mine in which alluvial sediments overlie a massive sandstone sequence which in turn lies at about one metre above the coal seam. The problems encountered include high levels of groundwater ingress to the pit, highwall instability, and an unacceptably high rate of blast hole collapse (prior to charging with explosives). Other aspects of the dragline stripping operation were also affected.

Jan 1, 1992