Search Documents

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

By Jan Dabrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures at each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 2D graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mu, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005

By R. H. Steel

Ingot casting and wire drawing In Iron Age Southern Africa by R. H. STEEL (Visitor) This paper describes the experiments that were conducted in 1974/1975 on two related aspects of Iron Age copper technology in Southern Africa: ingot casting and wire drawing. Three types of ingot were successfully cast: the St Andrew's Cross ingot, the marale ingot, and the musuku. It is suggested that the 'studs' on the musuku are not the remains of broken-off rods as previously proposed by other investigators, but that the ridged pattern is an ornamental feature. Copper wire was successfully drawn with similar tools and according to the procedures described in the literature on African Iron Age wire drawing. It is concluded that these accounts are generally accurate and that the pre-European metal workers are worthy of respect for the results they achieved with primitive methods.

Jan 11, 1975

By Young JA, Rogers G, Bannister S, Edwards SA

Many coal mine operators have responded to economic pressures by massive investment in machinery to reduce unit costs. To sustain the increased production which must justify the expenditure it is essential to know the resource in great detail months or even years in advance of its extraction. The required detail includes variations in composition and any lateral disruptions to the seam which night affect production. As Wilson (1985) has pointed out, a day's production loss can mean half a million dollars income forgone, and an unexpected major fault can mean a shutdown of weeks. Traditionally, seams were probed by surface drilling on (typically) 250 or 500m centres, and by horizontal drilling from sithin'the seam. Core was analysed chemically. The new generation machinery cannot tolerate the risk attendant on such widely spaced sampling, but the costs of much closer sampling rapidly become prohibitive.

Jan 1, 1987

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By Victor F. Hollister

North American ophiolite complexes are known to contain significant volcanogenic sulfide only in the following five areas: Newfoundland; Quebec; Applegate, Oregon; Rogue, Oregon; and Orca, Alaska. Most North American ophiolites, including the Baltimore, Kings-Sierra Nevada, and Del Puerto complexes, and those associated with the Franciscan, Trinity, eastern Oregon, and Cache Creek groups lack significant volcanogenic sulfide. The characteristics of sulfide-bearing ophiolites are: (1) manganozls cherts, and (2) fine, carbonaceous clastics inter- calated with pillow basalt and chert. It is suggested that sulfide- bearing ophiolite complexes developed in a restricted basin environment, such as is now present in the Gulf of California; whereas sulfide-poor ophiolites, formed in midocean, rises distant from land masses. Sea floor oxidation makes the typical midocean ridge configuration not conducive to sulfde preservation, whereas spreading centers bounded by land masses are more likely to produce anoxic physiographic lows favorable to sulfide accumulation.

Jan 1, 1982

By G K. Searle

In Australia, coal mines have generally not adopted filling to increase mining recovery. The aim of this project, entitled æImproved recovery in highwall mining using backfillÆ, was to examine the feasibility of using fill to improve recovery in highwall mining. Current fill practice was reviewed for metalliferous as well as coal mining, both here in Australia and overseas, for its applicability to highwall mining. Studies were then made at a conceptual level to determine whether fill could be economically used, to determine appropriate sources for fill and to trial key aspects of fill behaviour. A review of filling methods led to conceptual studies being undertaken on seven filling methods and these studies demonstrated that fill could be used to improve recovery. These studies were then further refined. Selected filling materials have been reviewed and laboratory tests have been made on these to assess their suitability.

Jan 1, 1998

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By V. N. Mackiw, D. E. Weir, D. J. I. Evans

The world&apos;s largest reserves of nickel are found in lateritic ores. Commercial exploitation has been carried out for almost one hundred years; however, none of the plants currently in operation produce pure nickel but rather ferronickel, matte, impure nickel oxide or mixed sulphide precipitate. Over the past decade Sherritt has studied various processes, including the modified reduction roast-ammonia-ammonium carbonate leach process, for the production of pure nickel powder and briquettes from laterites. Nickel can be reduced to the pure elemental form at elevated temperatures and pressures from impure basic nickel carbonate slurries. Several methods were studied in the development of the process for working up the pregnant leach liquor and basic nickel carbonate to produce feed for the aqueous hydrogen reduction step in which pure nickel powder is produced. This paper is concerned only with the laboratory studies using the basic nickel carbonate slurry reduction procedures.

Jan 1, 1973

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By Staunton W. P

The presence of cyanide soluble copper in gold ores can give rise to serious operational and economical difficulties in CIP and CIL operations. Cyanide consumption can result in the ore being uneconomic to treat by conventional means. Loading of copper onto carbon can also have deleterious effects on gold recovery and subsequent stripping and bullion recovery. The recovery of gold from high copper ores has been previously reviewed by Muir, LaBrooy and Cao (1989). Work undertaken for Mt Gibson Gold Project by Australian Mining Advisors with the assistance of the Chemistry Centre (WA) resulted in the patenting of a process and subsequent construction of a plant at Mt Gibson to overcome some of the difficulties encountered with copper. This paper discusses some of the work which was undertaken during laboratory investigations prior to commissioning of the plant and some further considerations for the treatment of high copper gold ores.

Jan 1, 1991

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach&apos;s results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K&apos; = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016