Search Documents

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

By J. Campbell

The hydrostatic tensions in pure metals and long freezing range alloys are evaluated theoretically considering the viscous flow of residual liquid and the general plastic collapse of the casting. The former mechanism operates until the radii of the remaining liquid channels are of the order of 10-3 cm radius, after which the second process limits the attainable negative pressures which range from —1500 to -4200 atm for nickel, aluminum, copper, and iron. In previous reports1'2 the maximum possible hydrostatic tensions developed during solidification have been evaluated employing spherical symmetry. This inevitably involves the concept of totally confined liquid regions, the reality of which has recently been brought into serious doubt3 following observations of the freezing of various transparent materials. Regions of interdendritic liquid which are apparently about to be isolated by the growth of dendrite arms are observed not to be cut off because the advance of the dendrite tips is arrested until the region has completely solidified. Although this may be the result of the very low melting point liquid available at this late stage in freezing, or the result of a higher rate of heat transfer to the dendrite tips because of the acceleration in liquid flow rate near the completion of solidification, this point need not concern us. In this paper an attempt is made to approximate more closely to real conditions; thus the assumption of confined liquid regions is abandoned and cylindrical symmetry adopted. It has also been necessary, therefore, to consider the viscous flow of residual liquid through the remaining channels in the pasty zone. Furthermore, the rather special conditions of spherically symmetric solidification led to extremely high solidification rates and hence unusually high tensile stresses as solidification neared completion; the cylindrical Symmetry appears to yield solidification rates and stresses which are more typical of real castings. The rate of solidification is first considered since this critically affects both the flow of the liquid and the creep of the solid.

Jan 1, 1969

By K. C. Heald

THE places where, yesterday, oil was unknown contain tomorrow's fields. Unquestionably, some states that now yield little or no oil have great potentialities, and developments in these states, although perhaps of less immediate interest than those in regions where great pools now exist, may easily be of greater ultimate importance than the results of exploration closer to known fields. Not long ago, Montana had only a quarter of an oil pool, and that was regarded by many as an accident that had strayed from Wyoming. More recently, the northern line of Louisiana was a dead line that would not be crossed by any Louisiana operator who valued his reputation for sanity. Within the past few months, Colorado has shown that it is far from being a negligible factor in the oil supply of the Rocky Mountain states, and it is now known that western Kansas, long shunned by many reputable geologists and operators, should be reckoned with. There may be a vast difference between what a wildcat well yields and what the well signifies. The fact that no commercial production is encountered may be lamentable and may well be disastrous to an individual or a company, but the same well that spells ruin to one may convey to another the information that will result in opening a new field. In presenting the conclusions, in this paper, the writer recognizes fully the possibility of erroneous deductions, particularly since he has had contact with only a few of the wells that are mentioned. Information comes principally from the scout. maps and files maintained at the Geological Survey by M. E. Latimer and G. K. Drach, without whose cooperation this summary would not be possible, supplemented by some personal contact and second-hand information gained by. conversation and correspondence. However, it is felt that the data contain few errors, and that the conclusions are at least reasonable.

Jan 3, 1924

By Bearman R. A

The majority of published material regarding the operation of crushing machinery is concerned with simulation of performance rather than design of equipment. The reason underlying the bias in published material relates to why research is carried out and who undertakes the research. Two distinct types of research can be identified: 1. Internal research by crusher manufacturers - generally related to mechanical design, value engineering and to the commercial realities attached to sales demands. Any work on basic crusher geometry or rock/machine interaction is of a sensitive nature and rarely enters the public domain. 2. Academic research - mostly confined to modelling of crusher performance and simulation. This is not because of any bias, but crusher design requires access to manufacturers data or at least an in-depth understanding of crusher design, which is rarely available. The crushing of rock is a complicated problem. It involves three aspects; the machine geometry, the material composition (type of rock/feed size distribution) and the machine/rock interaction. The machine geometry is often ignored in empirical mineral processing simulations, while the response of different feed materials is only nominally addressed in machine specifications provided by manufacturers. The manner by which the machine produces a stress field and causes different types of breakage for different rocks (or the machine/rock interaction) is sadly neglected by both groups. All three aspects must be considered collectively to successfully understand and model the entire crushing process. 1. Centre for Mining Technology and Equipment, Julius Kruttschnitt Mineral Research Centre, University of Queensland, Isles Road, Indooroopilly 4068 Qld. The importance of crushing is often underestimated. In mining and mineral processing the invisibility of the crushing process is understandable as it merely provides a coarse reduction stage prior to the intricacies of mineral extraction. However in the quarrying industry crushing and screening basically provide the finished product. A brief overview of the quarrying industry shows the importance of crushing. Figure 1 gives production figures for most of the western European countries, Australia and the USA.

Jan 1, 1995

By Georges Houlachi, Raynald Labrecque, Jean-Noël Cloutier

"Electrodialysis (ED) is an electro-membrane technology based on electrochemical process using electrical energy for the production of chemicals. The process can be used for concentrating, extracting, separating products, modifying molecules, purifying solutions, pH adjustment and regenerating salts into their base and acid. This paper reviews the principle of ED, present some of the different options and discuss applications that are relevant to the hydrometallurgy and mining industries for the treatment of effluents focusing on recovery of chemicals (acid and metals) and recycling of water minimizing the environmental footprint.INTRODUCTIONElectrodialysis (ED) is usually defined as an electrochemical separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution and other uncharged components [1]. ED technology consists of an electro-membrane technology based on an electrochemical process using electrical energy for the production of chemicals. It is a method combining electrolysis and dialysis was proposed for the first time in 1890 by Maigrot and Sabates [2]. In the late 1930s Teorell, Meyer and Sievers discussed membrane phenomena, revealed membrane potential, electric conductivity, transport number [3]. Meyers and Strauss introduced a multi-compartment ED apparatus consisting of two electrodes and a stack of ion-exchange membranes between them [1]. They succeeded to double the concentration of a KCL solution [3- Tarleton]. In general, ED consumes less energy than electrolysis to perform salt splitting. In that regard, one can expect an energy reduction of about 30% [4–5]. ED offers a great versatility in the domain of separation processes. Indeed, it can be used for concentrating, extracting, separating products, purifying by desalination, pH adjustment and regenerating a salt to acid and base components. This paper reviews the principle of ED, presents various options available and discusses potential applications relevant to the mining and metallurgy industries with economics of some successful industrial applications."

Jan 1, 2016

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By B Mohanty, G Ludwig

A thorough assessment of development drilling and blasting practice was carried out at two underground mines at INCO operations in Thompson, Manitoba. The study showed that significant improvement in productivity can be achieved through careful selection of explosives and loading practice, and modifications of the standard blast lay-out. The analysis involved assessment of the effectiveness of various perimeter blasting methods, employing selected explosives and loading practice in both jumbo and jack-leg rounds. The blasting pattern as well as burden and spacing were varied to determine their effect on the blast results. The various types of explosives used were, pneumatically loaded ANFO, with and without detonating cord tracing, extra-strength detonating cord, and slurry and emulsion explosives with and without cord tracing. The study also dealt with various means to achieve increased rate of advance in both jumbo and jack-leg rounds. The diagnostic measurements consisted of VOD, 'burn' marks or half-barrels on perimeter wall, and blasting vibrations. The effects of geology, firing sequence, blast lay-out, and drill hole deviation on the final results were also examined. The results of the study have been shown to have very important bearing on the design of development round blasting.

Jan 1, 1998

By T. P. Meloy

Improvement of grade and recovery requires the use of optimum processing circuits. Critical to an optimum circuit is the set point for separation. With the introduction of the concept of circuit analysis (Meloy, 1982), it became possible to determine optimum circuits for a given task. No analysis, however, has yet been made as to the grade requirements of the larger circuits. Williams and Meloy (1982), reviewed the literature and concluded that, within the operating range, most unit operations involved in particle separation behave linearly. For the purposes of this analysis, linearity will be assumed. Grade, G, is defined as the weight of the coal mineral, C, that appears in the product, divided by the weight of the coal mineral plus the weight of the gangue mineral or waste mineral, Q, which appear in the product.

Jan 1, 1982

By Gregory M. Rumbaugh, Todd R. Kostecki, Christopher Mark

The paper examines five massive pillar collapses in underground stone mines in the eastern United States from 2015 to 2021. These collapses caused significant airblasts, surface subsidence, and damage to mine infrastructure. The study identifies factors contributing to pillar collapses, such as slender pillars with width-to-height ratios of 0.8 or less, and proposes a framework for evaluating and mitigating collapse risks.

Nov 1, 2023

By D. J. Shields

The Sustainable Minerals Roundtable was established in 1999 to develop a set of national level indicators to measure the contributions of mineral and energy systems to sustainable development in the USA. The U.S. Forest Service and the U.S. Geological Survey are sponsors of the Sustainable Minerals Roundtable, with meetings convened by the University of Nevada, Reno. Eighteen meetings have been held in various regions of the United States to receive input from different communities of interest. Indicators are being prepared under four criteria: legal and institutional, productive capacity, environmental impact, and socio-economic. This paper reviews the process followed by the Sustainable Minerals Roundtable, and presents the priority indicators.

Jan 1, 2003

By Andre Pinsonnault, Francois Lefebvre, Yves Newman

In 1989, Les Entreprises Kiewit Ltee signed a C$32 million contract with the Societe d'energie de la Baie James, on behalf of HydroQuebec, to excavate the intake and tailrace channels for a second powerhouse at the LO-2A James Bay hydroelectric project. The multistage contract included removing three marine rock plugs. The first plug was blasted in April 1990. It was a 43 yards wide, triangular shaped wedge that projected into 18 yards of water. Located at the mouth of the intake channel, it contained over 72,000 yd3 of rock, more than twice the 30,000 yd3 found in most rock plugs.

Jan 1, 1991

By Frank J. Windolph

Grinding Practice-These tests were run in the 9 ft diam by 8 ft long grate discharge ball mills at Climax. Each mill functions in closed circuit with a 78 in. Akins duplex high-weir classifier, and a circulating load of 300 pct is maintained. The size of the mill feed is 6 pct on 3/8ths, which is ground to pass 28 mesh. Testing Methods-Each grinding section is equipped with a conveyor scale on the ball mill feeder belt, a watt-hour meter on the ball mill motor, and an automatic sampler for the ground product. These instruments are exceptionally valuable to the mill testing program.

Aug 1, 1956

By D. M. Larsen, N. D. King

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338°F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1994

By S. Jayasekera, A. M. T. S. Bandara, J. Kyle, E. Koenigsberger, L. Koenigsberger

The extraction of rare earth oxides from fluoroapatite rich phosphate concentrates often involves a weak acid leach of fluoroapatite and a sulphuric acid bake of the leach residue followed by water leach and precipitation to obtain an intermediate product. The main aim of this study was to determine and rationalize the solubility of rare earth metal ions in synthetic solutions representing various process liquors at the temperatures 40, 60 and 80oC. The liquors contained different acid and metal ion concentrations with respect to sulphuric acid, phosphoric acid and sulphate salts of sodium, magnesium, aluminium, potassium, calcium and iron(III). A solid of mixed rare earth carbonates was used as the source of rare earth metal ions. The solubility tests and characterization of solids using XRD were conducted at Murdoch University laboratories as part of the process development for the Arafura Resources Nolans rare earth project. The composition of initial carbonate solids and the solids and solutions formed after saturation were analysed for rare earth and other elements at TSW Analytical Laboratories in Perth using ICP-MS and ICP-OES. The precipitated solid in sodium-rich acidic sulphate solutions is the double salt NaRE(SO4)2 based on the solid assays. However, in acidic solutions free of sodium or of low concentrations of sodium the precipitated solid appears to be RE2(SO4)3.

Jan 1, 2014

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By H. M. Howe

The tenacity with which a bad name adheres to a process is well illustrated by the prevalent belief in the irregularity of the product of the Bessemer converter. We have been lately told by an eloquent member that lack of uniformity is the name of Bessemer steel, and that uniform soft steel can only be made in the Clapp-Griffiths Bessemer converter. Yet I believe that, however irregular the percentage of carbon in Bessemer steel may have been formerly, to-day it is well-nigh completely under control. Indeed, the results of a large number of analyses that I' have studied go to show that the

Jan 1, 1887

By M. A. Gimenes

The utilization of chlorination in extractive metallurgy and advanced ceramics areas has been widely investigated as a preparative route in order to obtain intermetallic compounds, which are used as precursors in the development of new materials and process. The major processes of decomposition of rare-earth ores use sulfuric acid and sodium hydroxide at high temperatures, however there is not much work concerning chlorination. In this work, a systematic study of the reaction between xenotime (REPO4), chlorine and carbon has been performed. Particular emphasis was on kinetic studies to establish optimized conditions for the reaction. The kinetics of chlorination of xenotime raw material by rare-earth elements/compounds has been studied over a temperature range from 600°C to 950°C. The influence on the rate of conversion of xenotime to RECl3 on temperature, partial pressure of chlorine, carbon content, and particle size were investigated. A global rate equation that includes these parameters has been developed. The results show that the process follows the unreacted core-shrinking model with a formation of a porous product layer. The powder X ray-diffraction technique corroborated this model showing clearly the patterns related to the formation of yttrium oxychloride (YOCl), indicating that the reaction mechanism involves the presence ofan intermediate step before the formation of lanthanide chloride.

Jan 1, 2000

By S. Chander

A review of the published literature on the mechanism of depression of sulfide minerals shows that a unified theory is not yet available. Various mechanisms that have been postulated include competition between depressants and collectors to adsorb at the surface sites, creation of thermodynamic conditions nonconducive for formation of a metal collector salt, or formation of a hydrophilic coating on the surface. The hydrophilic coating may or may not effect the adsorption of collectors. In another mechanism, the depressant may participate directly in oxidation/reduction reactions between collectors and sulfide minerals. Examples from the literature highlight oxidation/reduction effects in the depression of sulfide minerals.

Jan 1, 1986