Search Documents

By R. von Bonsdorff

Electrochemical and quartz crystal microbalance (QCM) methods were used to investigate the dissolution rate of gold in a solution similar to those utilized by the Outokumpu HydroCopper® process. The measurements were conducted in an electrolyte solution where [NaCl] = 2.8-280 g/L, pH = 1-2.5, [Cu2+] = 0-30 g/L and T = 70-95°C. According to these measurements, the solution flow has the greatest impact on the dissolution rate of gold in the HydroCopper® process. Under adequately acidic conditions (pH < 3), the dissolution rate of gold increases with increasing cupric concentration, increasing chloride concentration and increasing temperature. The results and trends observed compared well with the literature.

Jan 1, 2007

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By Robert L. Thoms, Joseph D. Martinez

The development of Gulf Coast salt domes thus far, although enormously successful and productive, has proceeded in an unscheduled fashion governed by events rather than by a comprehensive plan. Motivation for the sequential progress of exploitation has included mineral discoveries, inventions, technological improvements, new needs, and a dynamic economy. Although it is too late to implement a plan for the entire cycle of exploitation of this resource, it would seem advisable to introduce now a system concept for further development. Viewed from this perspective, general determinative parameters should include economic, environmental, logistical, technical, and resource considerations, and more fundamentally, basic societal goals. Experience gained from planning in the Gulf Coast should provide guidelines for use elsewhere in the world.

Jan 1, 1981

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By Adrian C. Dorenfeld

Concentradora "Doña Aida" (100 t /d capacity) was built in 1971-72 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals derived from two veins. The veins, Don Felipe and Maria, are about 150 m apart, but are distinctly different mineralogically. The deposits are near Sun Juan de Guadalupe, Durango, Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuilu. Sampling, ore testing, flowsheet design, plant design, drawings, purchasing, financing, and construction, etc., were planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1982

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By K. Price, G. Wang, L. R. Moore, Y. R. Xiong, J. Gu

"Sand is a naturally occurring granular material that is a result of the physical or chemical breakdown of rocks. Raw/natural sand contains various minerals, and it is this combination of minerals that brings the value to the construction aggregate industry. However, it is the quartz component of sand that is valued in its application as industrial silica in glass, high purity quartz, foundry sand, and oil and gas fracturing. Depending on the industry, the grade requirements can be the concentration of SiO2, particle size or shape, as well as contaminants such as the heavy refractory minerals, clays, fines, and alkali metals. With the ever declining mineral feed grade, processors continue to face challenges making the industry specific concentrate grade. As such, it becomes more important to tailor make the processing reagents to fit the mineral, processing conditions, and desired quality specification. This paper focuses on the application of novel collectors towards the beneficiation of sand for each of the major industrial silica applications. INTRODUCTIONQuartz is a mineral composed of a framework of silicon and oxygen atoms. It is the second most abundant mineral in the Earth’s continental crust. There are many species of quartz, which are defined by the particle size, shape, and color. Silica sand is one of those species, which is the byproduct of the physical or chemical breakdown of quartz containing rocks or crystals. Geologist define silica sand as a silica mineral with a particle size between 0.05 and 2 mm in diameter (Zdunczyk, 2001). Silica sand has significant value to society in recreation (beach sand and toy boxes), construction aggregate (concretes and asphalt), industry (iron & steel casting, fracturing proppants, and glass), as well as specialty products such as semiconductors or silicon wafers used in electronics.The aggregate business is the dominant consumer of silica sand products. Conversely, glass making, foundries (casting material), abrasives, and fracturing proppants are the dominant applications for industrial silica sand. Not much beneficiation is required for sand products going into the construction industry, other than sizing and scrubbing to remove clay. However, the industrial silica sand applications are dependent on particle size, shape, and degree of contaminants, which sets the market value (table 1). Therefore, as the more specialty products are produced, more sophisticated techniques and chemistry need to be applied to ensure the appropriate quality is met."

Jan 1, 2018

By Brien R. J, O&apos

Faster and more efficient methods of producing and refining iron and steel are imposing severe conditions on the refractory materials used to contain these metals in the molten state. In order to provide refractory linings which will give the desired service life and maintain unit availability at an economical level, it is necessary to appreciate the aggressive environment in which the refractories operate and determine the reaction mechanisms by which the refractories are destroyed. Only by such studies can the most suitable refractory or refractory combination for a particular unit be selected. Examples of refractories selection and reaction mechanisms are discussed for blast furnaces, BOS vessels, AOD vessels, steel ladles, vacuum degassing units and continuous casting.

Jan 1, 1976

The results of a systematic geochemical survey of rare elements are applied to elucidate genetic relations in a suite of rocks and to predict the probability of mineralization. The geology, radioactivity, major element geochemistry and classification of the main intrusives are described. The distribution of a group of rare elements, their concentration trends and the bearing these have on the emplacement sequence of the rocks are considered in some detail. The guides for exploration in the Pilanesberg that emerge are listed and some areas which substantiate predictions are described briefly. It is concluded that a study of rare element trends can make a considerable contribution as an exploration tool and for clarifying relations between the members of rock suites.

Jan 1, 1986

By Zofia Swierczek

This paper reports the results of a detailed mineralogical study of typical, low-grade Australian nickel laterite run-of-mine ores. Successful development of an effective beneficiation process for upgrading such low grade laterite ores relies on good knowledge of the laterite mineralogy and the value metal(s)? distribution characteristics. Both QEMSCAN and quantitative X-ray diffraction techniques were used to conduct the mineralogical analysis of three types of laterite ores, and the results were compared with those obtained by chemical analysis. Some of the major challenges faced included accounting for the mismatch between the nickel values measured by QEMSCAN and those recorded by chemical analysis. This was primarily due to the relatively low concentration of nickel in the ores and its wide dissemination among several major host minerals in complex association. Careful analysis showed that the limit of nickel detection in iron oxide host mineral grains under normal operating conditions was around 4%. Keywords: nickel laterites, mineralogy, characterisation, QXRD, QEMSCAN

Sep 1, 2012

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014

By Thomas Barkley

Mining tradition holds that a parallel round underground can not be any deeper than it’s smallest face dimension. ln other words, a mine using a 12’ (3.7 m) high by 24’ (7.3 m) wide room and pillar mine, the deepest pull that can be achieved is plus or minus 12’ (3.7 m). After experience with decking of rounds in a 12’ (3.7 m) diameter shaft to achieve more than 12’ (3.7 m) advance per round, the concept of deepening the pull on horizontal parallel rounds seemed to be a feasible concept. Tests were conducted in a conventional room and pillar metal mine with a round size of 12’ (3.7 m) high by 24’(7.3 m) wide. Standard rounds were drilled with a 16’ (4.9 m) steel as parallel rounds to an average depth of 14.5’ (4.4 m). The average depth of pull on these rounds was about 13’ (4.0 m). Using the available drilling equipment, 20’ (6.1 m) drill steel was used to drill holes to an average depth of 18’ (5.5 m). Five rounds were drilled and shot with a resulting aven$e pull of 16.2’ (4.9 m) or 90 % of drilled depth. Rounds were designed with decked bum cuts to maximize depth of pull in the cut area An innovative method of de&mining drilling accuraq was used to estimate it’s effect on depth of pull in the rounds. This method used a standard automatic 35-mm camera and scaling to determine the average drill deviation for many of the holes in the rounds.

Jan 1, 2000

By C. Gomez, J. Finch, R. Dalhke, J. Torrealba-Vargas

"The dispersion of gas into bubbles is an essential feature of flotation machines. Three measurements have typically been used to describe the dispersion: superficial gas velocity (Jg), gas holdup and bubble size along with the derived quantity, bubble surface area flux. Measurement devices continue to be developed. The McGill Jg sensor based on accumulating bubbles by natural buoyancy comprises a tube with a valve and pressure transducer (Figure 1). The tube is immersed at a desired location and depth (H1) in a flotation cell. On closing the valve pressure increases to a maximum (P1) when the tube is full of air. The Jg is estimated from the slope of pressure-time curve (dP/dt).The relationship between Jg and dP/dt is derived from first principles. Testing the relationship is difficult in a flotation machine as the spatial variation in Jg is generally not known. This problem is overcome using a specially designed experimental setup and the estimated Jg is shown to equal the known Jg.The derivation reveals the importance of bulk density (?b). The sensor was modified to provide an estimate of ?b (Figure 2). A second tube was added immersed to a different depth (H2) and kept full of accumulated air giving a pressure P2. The estimate of ?b is given by (P1-P2)/(H1-H2) (i.e., at the end of collecting the pressure-time data). This two-tube sensor also helps dampen process noise as illustrated by a sudden change in level when collecting the pressure-time curve. Both the original and modified versions have been widely used in plant test work."

Jan 1, 2003

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input-heat energy output) used in creating

Jan 6, 1951

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Song Yongxue

During the design and operation stages of a block caving project, a large amount of research and development work has been undertaken in the Tongkuangyu Copper Mine. This paper presents the research achievements from these studies, including a rock mass quality evaluation method, cavability prediction, fragmentation evaluation, caving mechanisms, a computerised production scheduling model and the optimised draw control system. The main features of the block caving system in the Tongkuangyu Copper Mine are also discussed.

Jan 1, 2000