Search Documents

By P. LaRochelle, K. Y. Lo, A. L. Tamuly Phukan

In many civil or mining engineering works, the stresses and deformations of natural or excavated slopes due to the combined effect of self-weight and initial stresses are of interest. Because of the mathematical complexities of this problem, however, no complete exact solution exists for the simplest case, that of assuming the stress-strain relation of the rock to be perfectly elastic. Efforts have therefore been directed toward numerical and experimental technique. The stresses within an elastic slope have been obtained by LaRochelle,1 using the photoelastic and finite difference method to determine the difference and sum of principal stresses. Subsequently, Finn,2 Hoyaux and Ladanyi,3 and Duncan and Dunlop4 attempted to solve the same problem by using the finite element method. The problem was also investigated by Brown and Goodman5 and Brown and King6 who emphasize the importance of the effect of loading or unloading procedure on the stress distribution within the slope. Although the geometry of the slope and the boundary conditions involved are identical or similar, the results obtained by these various authors by no means agree. It is therefore necessary to review briefly the results of elastic analysis in order to lend credence to the methods used in the solution. Although the stress-strain behavior of some rocks may be reasonably approximated by the elastic modrl, other rocks generally exhibit an elasto-plastic behavior with strain hardening or strain softening as shown in Fig. 1. Experiments show that for most rocks, the stress-strain relationship is approximately linear from the origin to the point P (neglecting the small concave region under low stresses). At P, the curve deviates

Jan 1, 1970

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

Colloquium And General Meeting - Trackless Mining in Underground Metal Mines A General Meeting and Mining Colloquium on the above topic was held on Wednesday, May 16th, 1973, at Kelvin House. Dr J. P. Hugo (President) was in the chair. The colloquium wasattended by approximately 200 delegates, and was opened by the President at 9.15 a.m. OBITUARIES The President: It is my sad duty to announce the death of the following: W. A. Schwezoff and L. G. S.

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By J. M. Mutmansky, T. K. Greer

This paper takes a look at the optimal velocity to be used in coal mine entries and determines a statistical relationship for optimal velocity that can be applied under current mining conditions. This relationship provides the optimal velocity for coal mine airways under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. This enables the ventilation engineer to make an easy, rapid determination of the optimal velocity for planning purposes.

Jan 1, 1985

By W. J. Garmoe

Distinct areas of mineralized and non-mineralized brecciated rock are found in the Ontario Unit of the United Park City Mines. These breccias contain an appreciable fraction of the present ore reserves and probably will become even more important as deeper levels are developed. Three ages of breccia have been recognized in the Ontario Mine to date: ( 1) Pre-mineral breccia that may or may not be mineralized, (2) early post-mineral breccia with mineralized fragments, and ( 3) late post-mineral breccia that is younger than and cuts through ( 1) and (2) above. These age ,relations are known from detailed underground mapping. Locally, both pre-mineral and post-mineral breccias have sufficient lead-zinc-silver content, either as matrix or fragmental material, to constitute ore. Ore-grade breccias occur throughout a vertical range of over 1000 feet and are found in both the Humbug and Deseret formations from above the Ontario 1300 level to below the Ontario 2200 level. The mineralized breccias, which are difficult to distinguish on mine maps, are not well delineated by underground workings, and their horizontal outline and vertical extent are not known beyond the immediate mining areas. The greatest amount of truly mineralized breccia is exposed on the 2200 level.

Jan 1, 1968

By Yasuhiko Ito

"This talk is concentrated on the topics of compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate. As a typical example, electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film is described. Another example is the formation of various kinds of intermetallic compound films including Ni2Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail.IntroductionGenerally speaking, surface film formation by molten salt electrochemical process can be divided into the following three categories:(i) single element film formation on the electrode by electrodeposition,(ii) compound film formation on the electrode by electrocodepostion of more than two elements, and(iii) compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate.This talk is .concentrated on the topics of category (iii), especially on the electrochemical implantation. Typical example can be seen in the electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film. Another example is the formation of various kinds of intermetallic compound films including Ni2 Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail with examples above as well as other experimental results also obtained very recently in the author's laboratory."

Jan 1, 2000

By A. B. Hooker, E. J. Coggeshall

"INTRODUCTION Ignitions of gas at the coal face when a blast is fired electrically are often a tributed to the explosive; but sometimes the ignition cannot be explained satisfactorily in this way-in fact, ignitions have occurred when the detonator has failed explode.The possibility of such electrically by sparks from the blast between poorly insulated leading wires and detonator leg have been recognized. Several countries have provided safe types of single-shot blasting units; some have permitted the use of larger multiple-shot blasting units provided each unit is equipped with a time-limiting switch that prevents unnecessarily long application of voltage on the leading wires after the shot has occurred, the assumption being that the firing line will this be dead before damage to the wires and subsequent sparking can take place. An extensive research was made by a French commission relative to the characteristics of electric detonators and methods of firing. Along other tailings they investigated the probability of ignitions by sparks across the leading wired at the face, also the time and duration of the various events in blasting, such as ignition of the detonators, movement of the coal face, and application of firing current. They suggested, as a means of eliminating or reducing tilt possibility of gas ignitions from the blasting unit, that the timing switch of the blasting unit be designed to disconnect the blasting"

Oct 1, 1934

By V. R. Spironello

Operating variables affecting the efficiency of the basic oxygen furnace (BOF) and the level of contaminating elements in the steel product were investigated by the Bureau of Mines. Steel was made in a 400-lb-capacity BOF designed to rotate on its vertical axis to increase the area of hot metal surface subject to oxygen attack. Hot metal for the BOF was made by melting pig iron and scrap in an 18-inch (ID) cupola. The variables were BOF speed of rotation, rate of oxygen flow, number of jets and angle at which they were machined into the oxygen-lance tip, temperature of hot metal, reactivity of lime, and temperature of scrap for the BOF charge. Experiments were arranged according to a two-level fractional-factorial design. The effects of the seven variables were evaluated for 13 responses. The greatest ingot yield occurred while using the larger angle lance tip and jets. The most carbon burned per unit volume of oxygen resulted from rotating the BOF and using the smaller angle lance tip. The largest sulfur transfer to the slag occurred at the higher hot metal temperature levels and higher rate of oxygen flow.

Jan 1, 1970

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10- to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 1993

By Cailing Zhen, Jian Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Guixiang Huang

The grate-kiln process has been widely applied for oxide pellet production with the quick development of steel industry in China, but ring formation takes place which adversely affects the productivity and properties of fired pellets. Rotary kiln at high temperature seems a black box, and ring formation is difficult to measure directly by current technology. It’s of great importance to monitor ring formation during firing of pellets. Therefore, a method for estimating the thickness of ring formation in rotary kilns was studied, based on working out theoretically the relationship between ring thickness and the outside surface of the kiln, according to steady-state heat transfer across a cylinder, which provides a soft-sensing technique for ring formation at high temperature, and achieves stable pellet production .

Jan 1, 2015

By C. Richard Tinsley

INTRODUCTION Documentary complications arise from the risk apportionment in project financing which generally means that once the project is up and running and has satisfied the lender's completion test, the loan agreement specifically limits the lender's recourse to the project and its assets. It is the purpose of this paper to describe the special considerations which apply to industrial minerals projects and explore the reasons why so few project financings are negotiated in this industry. SIZE Small projects do not warrant the relatively high costs of negotiating and documenting project financing. The extent of the documentation is directly proportionate to either (a) the degree of risk apportionment, or (b) the amount of control given to lawyers to negotiate the documents. Although one would like to believe that project-finance documentation could be off-the-shelf, it is almost always necessary to tailor the documents to the mine development itself and the individual desires of the borrower. Accordingly, the documentation costs and initial expenses are seldom less than $40,000, and for complex projects can reach $400,000. In addition, banks often charge an up-front fee to partly compensate them for their staff time and partly to increase their yield on what is deemed to be a "riskier" loan asset. Another factor is the generally lower debt:equity ratio when bankers are uncertain of the accuracy of the cash flow projections. The ratio of the amount of cash flow left over after debt service to debt service itself is a key tool for project finance (debt service coverage). Bankers will require a higher coverage ratio for industrial minerals projects because of the relatively higher uncertainties in the following categories: Prices Markets Geology/Quality Transportation Environmental This, in turn, means that lower debt:equity ratios are the norm for new industrial minerals projects. INDUSTRY STRUCTURE It is hardly worthwhile to generalise about a field as diverse as industrial minerals, but there are four other structural reasons why project financing has not been widely applied. 1. The most obvious example is the predominance of small-sized operations, largely a function of transportation economics. Geological conditions also contribute to their dispersion. 2. Often, the product is only a small part of a company's business in contrast to many petroleum, metals, or coal companies whose sole business is the production of the raw material. The construction industry is a good example here for cement, gypsum, crushed stone, sand and gravel, and the drilling-mud services business for barite and bentonite. A company is unlikely to jeopardise its main business through the failure of a project financing on one of its key inputs. The corrollary is that the mined input is often regarded as a cost centre and not run on the sort of economic basis suitable for project financing. 3. There may be a reluctance to reveal key aspects of an industrial minerals venture to an outsider for purely competitive reasons. Unlike the other minerals industries which readily share technical information at plant visits and

Jan 1, 1985

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By D. J. C. Taylor, R. A. Kruger

Unbridled mining operations can have a serious negative impact on the surroundings. With the recent increased awareness of the need for environmental conservation and the resulting advances in environmental control, the mine planner has new tools at his disposal for the successful implementation of mining projects while avoiding negative environmental effects. This paper discusses the environmental strategies adopted in the planning and commissioning of a trial underground coal mine. The minimization of negative environmental effects is demonstrated and, where applicable, environmental benefits are examined.

Jan 1, 1986

The Airport Link Railway utilises innovative solutions to a number of issues associated with underground development and transport infrastructure planning. It is typical of the major change underway in the countryÆs rail and air transport industry. It involves the private sector providing transport facilities in competition with the public sector, a convergence of planning and transport imperatives, the use of the most technologically advanced engineering practices to minimise construction impacts on the community and a commercialised way of developing and maintaining railway infrastructure and services.

Jan 1, 1999

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology resulting from substitutions of other materials and increases in production efficiency. The purpose of this paper is to use the material composition of product to show the impact of advanced materials on the use of traditional metals.

Jan 1, 1992