Search Documents

By B. H. Kear

Clustering of slip bands in different systems has been observed in both ordered and disordered Cu3Au crystals compressed in the <110> orientation. Certain features of the slip band patterns are explained in terms of reactions between dislocations with Burgers vectors at 120 deg; in a few rare cases, the slip band evidence suggests that the Products of such reactions form diffuse tilt boundaries between the differently slipped regions of the crystal, similar to the known behavior of ionic crystals, but not nearly so well defined. WHEN crystals with orientations favorable for multiple slip undergo plastic deformation, slip may occur in different systems in localized regions, so that clusters of slip bands are developed. This phenomenon has been observed in fee1-4 metals and also in ionic crystals having the sodium chloride structure.5-8 In the ionic crystals, the boundaries formed between the differently slipped regions of the crystal assume characteristic orientations and are associated with macroscopic tilts that are plainly visible on the sides of the crystal. Recently, this interesting feature was explained in terms of the formation of diffuse low-angle boundaries as a result of interactions between families of glide dislocations in the different systems meeting in the boundaries.9 This paper describes an attempt to obtain similar evidence for boundary formation in an fee crystal. The alloy Cu3Au was chosen for the present study simply because this material is currently being used in a general study of differences in deformation behavior of the ordered and disordered phases of this alloy, which will be described elsewhere. EXPERIMENTAL PROCEDURE The two specially oriented compression specimens used in the present study were prepared from a melt-grown single crystal by careful cutting, grinding and polishing. The finished specimens were about 6 mm by 2 mm in cross section by 6 mm tall, with their ends parallel to (101) and sides parallel to (111) and (121); the broad faces of the specimens were made parallel to (711). Both specimens were annealed in an evacuated quartz tube at 850oC for several hours, slowly cooled to 500°c, and then quenched into water in order to obtain the disordered state for the alloy. One of the specimens was partially ordered (with S- 0.8) by reannealing at 350oC for 100 hr. After these annealing treatments, both of the specimens were electropolished. 10 Finally, the specimens were compressed in the [loll orientation and their stress-strain curves were recorded. The deformation was carried out in increments of a few percent strain. At each stage in the deformation the specimens were unloaded, removed from the compression jig, and examined optically for slip bands. Before reloading, the specimens were repolished, so that the observed slip band patterns were characteristic of a particular stage in the deformation. EXPERIMENTAL RESULTS Fig. 1 show!; the stress-strain curves for the ordered and disordered specimens and also indicates the stages 1, 2, and 3 where the deformation was interrupted for examination of slip bands. The curves show marked differences in flow stress and in work hardening rate in the two specimens, as observed by previous workers.11,12 Also, it was found, in agreemement with the observations of Taoka and Sakata,&apos;3 that the plastically deformed disordered alloy showed the characteristic coarse slip bands of alloys, whereas the ordered alloy exhibited a fine slip band structure similar to that of pure metals. Slip Band Observations. In what follows, the description of the slip band patterns, with accom-

Jan 1, 1962

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-&apos; and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.&apos; An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By Coleman D. Hunter, George M. Straughan

Oil and gas development as well as extensive leasing in Kentucky during 1940 has shown a marked improvement over the past three years.$ The most noticeable improvement is the gas development in eastern Kentucky and the deep tests being drilled by major oil interests. In western Kentucky, 406 wells were drilled, of which 173 were oil producers, 12 were gas wells and 221 were dry or abandoned. The number of dry tests was large, because no important, new oil or gas pool was discovered and many of the dry holes could be considered wildcat tests. However, with either oil or gas possibilities from Pennsylvanian formations on through Mississippian, Silurian, Devonian, and Ordovician, this percentage of dry holes seems rather high. Many of the dry tests possibly should have been tested in deeper horizons before being abandoned: namely, Silurian and Ordovician ages. In eastern Kentucky, 213 wells were drilled, of which 113 were gas producers, 61 were oil wells, and 39 were dry holes. Of these wells, 117 were drilled in the most important Big Sandy gas field, in Floyd, Pike, Knott and Martin Counties, and of this number 103 were gas producers, 5 were oil wells, and 9 were dry holes. In the Big Sinking oil field of Estill, Lee and Powell Counties, 70 of the remaining 96 wells were drilled, j6 being oil producers. During 1940, four deep tests were drilled in eastern Kentucky. One test penetrated the Knox dolomite in Knox County and was dry; no St. Peter sand was encountered. Another test in Lee County had some gas in what might be called St. Peter sand, according to the State Department, and also some gas deeper in the Knox dolomite. In Wolfe County, a small oil well was completed in the Ordovician, which was undoubtedly of Trenton age. ilt the present time, four deep tests are being drilled, all of which will go to the Knox dolomite. In Elliott County, on the Burke dome, the Inland Gas Co, is drilling at 3650 ft. In Magoffin County, on the Paint Creek uplift, the Cumberland Petroleum Co. is drilling at 3800 ft. In Clark County, in the Ruckerville fault area, W. 0. Allen is drilling at 1800 ft. In Laurel County, on the Sinking Creek dome, the Globe Oil and Gas Co. is drilling at I750 ft. If production is encountered in the Trenton, St. Peter, or Knox dolomite in any of these tests, eastern Kentucky will experience a marked increase in deep development.

Jan 1, 1941

By George M. Straughan, Coleman D. Hunter

Oil and gas development as well as extensive leasing in Kentucky during 1940 has shown a marked improvement over the past three years.$ The most noticeable improvement is the gas development in eastern Kentucky and the deep tests being drilled by major oil interests. In western Kentucky, 406 wells were drilled, of which 173 were oil producers, 12 were gas wells and 221 were dry or abandoned. The number of dry tests was large, because no important, new oil or gas pool was discovered and many of the dry holes could be considered wildcat tests. However, with either oil or gas possibilities from Pennsylvanian formations on through Mississippian, Silurian, Devonian, and Ordovician, this percentage of dry holes seems rather high. Many of the dry tests possibly should have been tested in deeper horizons before being abandoned: namely, Silurian and Ordovician ages. In eastern Kentucky, 213 wells were drilled, of which 113 were gas producers, 61 were oil wells, and 39 were dry holes. Of these wells, 117 were drilled in the most important Big Sandy gas field, in Floyd, Pike, Knott and Martin Counties, and of this number 103 were gas producers, 5 were oil wells, and 9 were dry holes. In the Big Sinking oil field of Estill, Lee and Powell Counties, 70 of the remaining 96 wells were drilled, j6 being oil producers. During 1940, four deep tests were drilled in eastern Kentucky. One test penetrated the Knox dolomite in Knox County and was dry; no St. Peter sand was encountered. Another test in Lee County had some gas in what might be called St. Peter sand, according to the State Department, and also some gas deeper in the Knox dolomite. In Wolfe County, a small oil well was completed in the Ordovician, which was undoubtedly of Trenton age. ilt the present time, four deep tests are being drilled, all of which will go to the Knox dolomite. In Elliott County, on the Burke dome, the Inland Gas Co, is drilling at 3650 ft. In Magoffin County, on the Paint Creek uplift, the Cumberland Petroleum Co. is drilling at 3800 ft. In Clark County, in the Ruckerville fault area, W. 0. Allen is drilling at 1800 ft. In Laurel County, on the Sinking Creek dome, the Globe Oil and Gas Co. is drilling at I750 ft. If production is encountered in the Trenton, St. Peter, or Knox dolomite in any of these tests, eastern Kentucky will experience a marked increase in deep development.

Jan 1, 1941

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson&apos;s Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson&apos;s Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson&apos;s Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile &apos;&apos;Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson&apos;s Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson&apos;s Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson&apos;s Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile &apos;&apos;Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By John B. Umhau

In 1930 , 65,448 long tons of virgin or primary tin were consumed by 1,292 establishments in the United States , representing about 91 per cent of the total consumption as computed from imports , exports , and stocks at the beginning and the end of the year . The reported consumption was equivalent to 38 per cent of the world's tin production in 1930 , estimated at 171,000 tons , and was 12 per cent less than the 74,369 tons consumed by 1,307 establishments in 1928 . Decreased consumption of new tin in 1930 ás compared to 1928 was a reflection of the general industrial depression . All of the tin- consuming industries showed substantial decreases except tin plate and terneplate , white metal , and tinning , which showed small tonnage increases aggregating only 1,200 tons . The largest tonnage decrease was in the use of new tin in babbitt which declined 33 per cent in 1930 as compared to 1928. This was largely attributable to the decreased production of automobiles and trucks , which was 24 per cent lower in 1930 than in 1928. Percentage decreases in other important tin- consuming industries were as follows : Solder 18 per cent , bronze 19 per cent , tin foil 40 per cent , chemicals 23 per cent , tin oxide 44 per cent , and type metal 46 per cent . The distribution of the amount consumed by various uses during 1927 , 1928 , and 1930 is shown in table 1 . Consumption studies indicate the fact that variation in tin consumption from year to year parallels the fluctuations in demand for the already wellestablished tin products . For example , the manufacture of motor cars and trucks3 required only 11,000 tons of tin in 1930 compared to 19,000 tons in 1928 ; the canning industry continues to require the greater portion of the tin plate and much of the solder . Recently developed industries , while affecting total consumption of bearing metals , solders , etc. , to some extent , have made little change in the relative importance of these commodities as consumers of tin .

Jan 1, 1932

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By S. A. Ford

A SHORT and accurate method for the estimation of manganese in iron and steel is of great advantage to Bessemer works, and I think it may be of interest to some of the members of the Institute to give in detail the process in use in the laboratory of the Edgar Thomson steel works. The process is based on the reaction first described by Beilstein and Jawein.* The steel, spiegel, or iron is dissolved in strong nitric acid, sp. gr. 1.4. Evaporation to dryness is not necessary, unless the amount of silicon is large, as in the case of certain pig irons. Then, as a clogging of the filter in the subsequent filtra¬tion is apt to follow, dissolve first in a dish in hydrochloric acid, quickly evaporate to dryness, redissolve in the strong nitric acid, boil, and while boiling throw in crystals of chlorate of potash from time to time. Violent action ensues, yellow fumes are given off, and binoxide of manganese is precipitated, since it is insoluble in strong * Berichte der deutschen chemisehen Gesellschaft, vol. xii, page 1528.

Jan 1, 1881

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity. On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can not be designed to be 100 per cent efficient and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the computed figures of heat requirement per carrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, &apos;the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil.

Jan 1, 1931

By C. W. Merrill

The price records of seven representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When these records are reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum), and two nonmetals (sulfur and cement) have been chosen because of their pre-eminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities were selected before any price figures were compiled; none was selected or rejected to substantiate any preconceived notions as to price trends. The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the U. S. in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons. Two such comparisons have been made: 1) The quantities of each of the commodities that could have been purchased for an average hour&apos;s wage in each year, and 2) the unit price of each commodity through the years in terms of deflated dollars. These data are set forth in the accompanying table and two charts. The quantities of the mineral commodity purchasable with the average wage for one hour&apos;s work in all manufacturing industries through 1926 were based on annual average prices and on average annual wage rates determined by Paul H. Douglas and published in his "Real Wages in the United States, 1890-1926." The series was extended through 1957 by the Bureau of Labor Statistics, U. S. Department of Labor. Calculations based on these data show that the average worker could have purchased 1.28 lb of copper with his hourly wage in 1890, whereas his hourly wage would have purchased 8.11 lb in 1957, an increase of 633 pct in the 68-year period. An average hour&apos;s wage would have bought 10.85 gal of petroleum in 1890, compared with 33.04 gal in 1957. Even more spectacular is the increase in sulfur, of which 25.25 lb could have been purchased with the 1904 average hourly wage; 223.08 lb were purchasable with the wage in 1957—an increase of 883 pct. Comparable price data for sulfur are not available for years earlier than 1904. For every commodity, the calculations show an improvement in the wage earner&apos;s purchasing power in 1957 compared with the early years. Measuring purchasing power in terms of wages does not give an entirely fair picture of the availability of a commodity in an economy. When the efficiency of an economy changes and the balance shifts among such elements as raw-material production, manufacturing, and service trade, the economic significance of an hour&apos;s work changes. Partly to meet such criticism, but mostly to present another interesting measure of the response of minerals to changing market conditions, a second set of calculations has been made to deflate unit prices for the seven commodities into terms of 1954 dollars. To accomplish this adjustment to a common 1954 parity, the Gross National Product Price Deflator, developed by the Office of Business Economics, U. S. Department of Commerce, was used. Although the results of these calculations are not as striking as those based on labor&apos;s increasing purchasing power, nevertheless the declines outweigh the rises in the prices of the mineral commodities. In terms of these deflated prices, aluminum and sulfur are much cheaper today than in the early years; copper was substantially cheaper in 1957 than in 1890; pig iron and petroleum are little changed; and only bituminous coal and cement have increased substantially. Strangely, the two mineral commodities with the strongest reserve positions are the two to exhibit rising real prices. Now this apparent overall downtrend in prices has taken place during a period of almost fantastic increase in the demand for mineral products. The value of minerals consumed in the world during the period greatly exceeds all mineral consumption up to 1890. A stage has been reached in the U.S. in which 95 pct of the energy used is of mineral origin and in which machines, structures, roadways, communication facilities, and most other elements in the industrial economy are primarily of mineral origin. Even agricultural fertility is maintained, in large measure, by mineral fertilizers. A series published in Minerals Yearbook shows that the value of U. S. mineral products has risen from $615 million in 1890 to $18,000 million in 1957, a 29-fold increase. Even in deflated dollars, the increase has been eightfold, while population has expanded less than threefold. Not only are demands of the industrial nations— the U. S., countries of Western Europe, and Japan— increasing at rapid rates, but those countries with agrarian economies are calling themselves underdeveloped and clamoring to industrialize. The ever-expanding mineral requirements in the U. S. and throughout the world show no abatement. Mineral reserves frequently have been described as wasting assets. Much concern has been shown for future users, who have been pictured as finding themselves on a plundered planet. Conservationists have viewed the future with alarm and have demanded legislation and regulations to reduce the drain on mineral reserves.

Jan 1, 1960

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the &apos;indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873