Search Documents

By L. G. Austin, R. R. Klimpel

This communication points out that serious errors exist in some current treatments of the random fracture of solids, including the prior treatments by Klimpel and Austin, Gilvarry, and Gaudin and Meloy. The problem considered in all of these papers is: what cumulative weight versus size distribution is expected for the fragments produced by fracture of a particle? The basic assumption made is that fracture surfaces propagate in random directions from weak flaws in the solid (these weak flaws being activated to fracture by applied stress), with the activated weak flaws distributed at random spatially within the solid. The previous treatments considered fracture in three dimensions, and all use similar physical models, although the mathematical techniques were somewhat different. We first noticed that these treatments were in error when we attempted to reduce the equations developed to the simple case of fracture of a one-dimensional particle, e.g. a long, thin fiber which breaks along its length. For this simple case, it is readily shown that the assumption of random fracture leads to the expression P(V) = (r/Vo) (1-V/Vo) r-1 dV (1) is the probability of occurrence of a fragment of length within the range V to V + dV; V being length dimension, from r random fractures passing through an original size of Vo to produce r + 1 fragments. This equation agreed with the one-dimensional form of an equivalent equation in the original Klimpel-Austin treatment. However, in this treatment it was then stated that, "The fractional weight below size V is [ ]

Jan 8, 1968

By N. A. Ziegler

CONSIDERABLE work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Wood,1 about reactions between the alloys and atmospheric gases and still less is known about changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resist-ing" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown' that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900° C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form Si02 or more complicated (silicate) inclusions. Another possi-bility to be considered was that during annealing in oxidizing atmos-pheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. Yensen,3 the writer set out to investigate this problem about two years ago in order to settle these questions.

Jan 1, 1934

By R. L. Neman

Southern Oklahoma (including the Arbuckle Mountains) has outcrops of rocks representing Precambrian, Paleozoic, and Cretaceous ages. Thus, rocks of every geologic age in the Paleozoic and Mesozoic Eras, except the Jurassic and Triassic Periods, are present in south-central Oklahoma. With rocks of such an enormous age range present in a relatively small geographic area, it is little wonder that a wide variety of economic rock and mineral resources are locally present. This report will describe the occurrence, mining, processing, and end-uses (dictated by chemical and physical properties) of the Precambrian Troy Granite, the Cambrian Royer Dolomite and Fort Sill Limestone, Ordovician silica sands of the Simpson Group, Ordovician limestones of the Viola Springs and Welling Formations, and Ordovician Sylvan Shale. In general, the more the end-use depends upon chemical composition and purity, the greater the price that can be demanded for such-minerals. The not-so-successful attempts to mine zinc, manganese, copper, and iron from the Arbuckle Mountains also will be discussed briefly, and I will provide a sermonette on analytical chemistry and its usefulness to corporate CEOs. I may be one of the few persons at this Forum on the Geology of Industrial Minerals who is not a professional geologist. I am an analytical chemist specializing in geochemistry. In particular, I investigate trace elements in rocks and their consequences in industrial processes. As such, I have consulted to the mining industry (and their clients) for two decades, always with the intent of improving service and product quality.

Jan 1, 1999

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Eugene F. Eisemann

This paper is concerned principally with the competition between fuels for industrial use in the United States. Total energy consumption in the U. S. is allocated between industrial and other uses The industrial volume is divided into two classifications (1) where-there is competition between fuels and (2) where there is no competition. The pattern of fuel consumption by electric utilities was studied because there, is competition between fuels and because it is the fastest-growing industrial market. Electric utilities fuel consumption is discussed by geographic area. The growth of each fuel in several areas is investigated. The analysis of these areas, includes the study of the relationship between prices where fuels are in, competition:- (1) on the East Coast where price competition occurs between oil and coal, and (2) in the southeastern states where competition exists between coal and gas..

Jan 1, 1961

By G. S. Rao

Levitated drops of Fe-18%Cr-2%C were reacted with oxygen-argon mixtures to study the reactions that occur in the AOD process, where the gases are injected into the melt and form bubbles. In the laboratory an argon-oxygen pulse, followed by pure argon, was flowed past the levitated drop to simulate the transient conditions in the gas phase as the bubbles rise in the melt. Oxide layers formed on the drops immediately when they came into contact with gas pulses containing 75% or more oxygen. Once the oxygen flow had ceased, the oxides reacted with the carbon in the drops to form CO gas and eventually disappeared. The de-carburization reaction occurred without oxide formation when the gas contained 50% oxygen or less. Melts that were sampled after EAF tapping, ready to be charged into the AOD, showed a higher tendency to oxide formation and consequent carbon boil than pure ternary Fe-18%Cr-2%C alloys made in the laboratory. The actual steel samples contained significant impurities, such as 0.25% Si and 0.56% Mn. A similar effect of oxide-forming impurities had been observed previously with binary Fe-C alloys. Movies were taken of the oxide formation and decomposition, and the results will be presented, along with data on the experimental conditions, including temperature and oxide compositions. The results are important because they give an insight into the reaction mechanisms in the AOD, which must be understood in order to improve and model the process.

Jan 1, 2006

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

By Anna Szostak-Chrzanowski, Adam Chrzanowski

"New techniques in monitoring surveys and new methods in the analysis and prediction of ground subsidence are being developed in the Department of Surveying Engineering at the University of New Brunswick (UNB). The new surveying techniques include a telemetry monitoring system developed at UNB in cooperation with CANMET, and use of the satellite Global Positioning System. A generalized approach to the analysis of deformation surveys has been developed which permits an integrated analysis of geodetic and geotechnical measurements in geometrical modelling of ground subsidence. A computer program, FEMMA, has been developed for the elastic and non-linear elastic analysis and the deterministic prediction of deformations using the finite element method.IntroductionResearch and development of new monitoring techniques and new methods in the analysis and prediction of ground subsidence in mining areas is an integral part of a broad research program on deformation surveys which is being carried out in the Department of Surveying Engineering at the University of New Brunswick.The research concentrates on:developmentof a general method for predicting deformations with an emphasis on the use of the non-linear elastic finite element analysis; development of a generalized approach to the geometrical analysis of deformation surveys with an integration of geodetic and geotechnical measurements; and development of new monitoring techniques with an emphasis on continuous data acquisition and application of new space techniques such as the satellite Global Positioning System (GPS).This paper gives a brief report on the progress and recent developments within the above program."

Jan 1, 1987

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn). As result of chemical analysis of Mn, Cu, Ni and Co, polymetallic nodules observed in part of the EEZ of Mexico are possible of potential economic interest (Rosales and Carranza, 1990, 2001; Carranza and Rosales, 2003).

Sep 14, 2011

By S. E. Maddigan

MANY experimental and theoretical investigations have been made on the processes involved in annealing and recrystallization of metals. Most of these, however, have treated the time element as constant and heat-treatments used have been for relatively short times. Aside from the early work by Carpenter and Elam,1 the few that have investigated the effect of time on the processes have usually done so for fairly short time periods. During recent years the growing interest in long-time creep properties of metals and alloys under stress has made increasingly important a better knowledge of the recrystallization during prolonged heating. The recrystallization temperature of 70-30 brass given by Clark and White2 in 1932 was somewhat above 400°F. (204°C.) but under 500° (260°C.), whereas in our laboratory recrystallization has been observed in creep specimens at 204°C, the lowest temperature of Clark and White's range. Since the creep properties are quite different above and below the recrystallization temperature, erroneous conclusions can readily be drawn by the application of short-time recrystallization data to creep problems. It was thus considered of both practical and theoretical value to make long-time annealing studies near the minimum recrystallization temperature. In this way useful additions could be made to data on recrystallization temperatures and, since the reactions in this range are relatively slow, additional insight could be obtained into the factors involved in annealing. Several comprehensive reviews of recrystallization processes have been written,3-5 therefore only a brief review of the generally accepted facts will be given here.

Jan 1, 1940

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

In spite of the tremendous amount of research conducted in the last few decades. no single blasting theory has been developed and accepted that adequately explains the mechanisms of rock breakage in all blasting conditions and material types. Given specific test environments, conditions and assumptions, individual researchers have contributed valuable information and insight as inputs into blasting theories, although a simple "plug-in" type formula for predicting optimum fragmentation, muck pile geometry and casting distance, is still largely unresolved. There is as yet, no consistent and widely applicable theory of blasting, but only a number of limited and disconnected theories; many of which are empirical in nature and based on ideal blasting conditions. Blasting theories have been formulated and based on pure speculation, years of blasting experience on a trial-and-error approach, laboratory testing, field investigation, and mathematical and physical models adapted from other disciplines of science.

Jan 1, 1988

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of&apos; the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.&apos;,&apos; The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949