Search Documents

Study on Basic Theory of the Grain Settlement in Fluidised Bed This paper takes thick goal grains (less than 1.5 cm) as research object. According to different densities and particle sizes, thick goal grains are divided into 20 kinds of narrow density and narrow size level average grains. Free settling and hindered settling tests are respectively carried out in ?100 fluidised bed thick goal separators. Hindered settlement includes hindered settling velocity test and measurements of suspension density. Results show follows. (1) Fluid state in separator belongs to transition region. Alien's law is the appropriate formula of thick coal particles free settlement terminal velocity. (2) The main factors affecting hindered settling velocity are the number of solid particles in medium and the structure feature of the particle group. The bigger volume fractions of solids ? is, the smaller decreasing velocity coefficient of particle hindered settlement ¯ becomes. In the organism from bottom to top, density of suspended particles in fluidised bed gradually decreases, but near the top of the suspended particles, the density increased slightly. With increase of density and size, suspension density reducing extent increases from bottom to top of separators.

Sep 13, 2010

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By Keith Rowley, Neal Harries, David Noon

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, South Africa, Zambia, Chile and the United States. Greater than 70 rock falls and waste dump failures (from several to millions of tonnes) have been monitored, and on every occasion precursor ?warning? movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines.

Jan 1, 2006

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By D. L. Douglas

The ß decomposition of Zr-U-O alloys was studied during an interrupted quench from the a + ß region. Decomposition was more rapid than in binary Zr-U alloys of the same uranium content or qf equivalent ß composition. The rapid transformation has been ascribed to the presence of the primary a phase which provided nucleation sites and which permitted preferential partitioning of oxygen to the a phase and of uranium to the COMMERCLAL heat treatments are designed to produce certain strength and toughness character- istics by controlling the microstructure of an alloy. A desired distribution of microconstituents is achieved in practice by treating an alloy under the correct time-temperature conditions. A knowledge of the phase equilibria in any alloy system is essential in outlining heat treatments, but in addi-

Jan 1, 1961

By Ebrahim Ghasemi

Roof fall risk is a common problem in coal mines, and it is generally unpredictable due to variability in geological and mining parameters. In this study, a new fuzzy logic model was developed to predict roof fall rate in coal mines. Parameters such as coal mine roof rating (CMRR), primary roof support (PRSUP), intersection span, and depth of cover were considered as the model inputs. The model was developed based on experts? knowledge and also a database including about 109 datasets of roof performance from U.S. coal mines. Approximately 20% of these datasets were used to assess the performance of the fuzzy model. In each case, comparison between results from model and real roof fall rate showed that this model can predict roof fall rate to an acceptable extent.

Jan 1, 2011

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

By G. Favini

A Bayesian decision model of minimun risk, based on the probability and costs of mine discoveries and non-economic projects, is presented for massive sulphide exploration in the Canadian Shield. The sample used for the model is composed of data relating to forty mines, sixty non-economic sulphide occurrences, and sixty occurrences of graphitic and pyritic material. These economic and barren samples consist of drill-tested occurrences which were, in varying degree, characterized by conductivity anomalies. Given the large size, the reliability and the homogeneity of the data base available for massive sulphide exploration, it is shown that certain statistical models can and should be utilized as a tool for decision-making by explorationists. Given this data base, information theory tells us that only those signals that are independent of one another will transmit information with minimum error. An ensemble of six significant multilevel signals, markedly independent of one another and consisting of numeric and geometric form descriptions derived from Bouguer anomaly, aeromagnetic and physiographic maps, were identified and evaluated by case studies. The use of these signals as input in a simple statistical procedure, or in a carefully planned and experienced visual appreciation scheme, can be of significant aid in decisions concerning the choice of favourable areas or sectors to explore in detail. The method of discriminant analysis is theoretically and practically suited for the statistical modelling involved. By way of a simulation on our statistical model, the efficiency of the model and of the underlying criteria is determined for historic cases and, by inference, for its validity in future exploration. An approximate optimized solution is derived from the model which suggests that over 90% of the known ore could be found by screening, according to a model such as that herein described, and drilling only 30% of the targets (mostly barren) normally identified and tested in current and past exploration.

Jan 1, 1979

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By Khaled Morsy

Longwall mining is one of the most widely practiced underground coal mining method. The behavior of the longwall gob is very critical in the understanding of the complex ground response to longwall mining. In the limited data available, the values of gob moduli used in numerical modeling ranged from 1,000 psi to over 300,000 psi. Such a wide variation in moduli would greatly affect the results of the numerical analysis. A better understanding of the behavior of the gob will allow numerical models to be more accurate for simulating longwall mining conditions. In this study, a gob model based on the Terzaghi's model was incorporated into the comprehensive finite element package, ABAQUS, to simulate the loading behavior of longwali gob material. A case study was used to verify the proposed gob model.

Jan 1, 2002

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

By G. Osuch, G. Derge, G. M. Pound

Using a new dternating-current potentiometer circuit and a specially designed four-terminal cell, the specific conductance of molten Cu2S-FeS mattes was measured as a function of temperature, from the liquidus to 1500°C, over the complete range of composition. The high conductivities, about 1500 ohm-I cm-l for FeS and 100 ohm-l cm-l for Cu,S, indicate that the conduction is electronic rather than ionic. Molten FeS has a negative temperature coefficient of specific conductance, resembling metallic conduction. Molten Cu,S has a positive temperature coefficient, resembling semiconduction. The binary roughly follows an additive rule of mixtures with respect to both magnitude and temperature coefficient of specific conductance. Metallic bonding in the liquid is postulated to explain these phenomena. MUCH has been learned in the past about the nature of liquids and the ionic or molecular species in solution by means of electrical measurements. Thus, dielectric constants','2 have given information about molecular liquids such as water and benzene. Measurements of dielectric constant usually are impossible in electrically conducting liquids, such as aqueous solutions of ionic salts and molten ionic salts. However, measurements of electrical conductance and ionic transference have provided much knowledge about the latter systems.a-" In recent years, the ionic nature of certain molten metallurgical slags has been established by Derge and Martin7 through electrical conductance and electrolysis measurements. Chipman, Inouye, and Tom-linsonq ave studied the electrical conductance of molten FeO and report a high specific conductance of about 200 ohm-' cm-' (compared with 4 ohm" cm-' for an ordinary ionic liquid such as molten NaCl) and a positive temperature coefficient of conductance. They interpret these results in terms of p-type semiconduction by analogy to the situation in solid FeO.Y imnad and Derge" have studied cell efficiency in the electrolysis of molten FeO-SiO, systems and conclude that ordinary ionic conductance increases with SiO, content. Very recently, interest has been revived in the electrical conductance of liquid metals and liquid metallic solutions. Scala and Robertson1' report a close resemblance between the liquid and solid states with respect to thermal, structural, and compositional relationships. Molten sulphides have not received a great deal of attention. Bornemann and von Rauschenplat" measured the specific conductance of molten Cu2S as a function of temperature with a four-terminal cell using direct current. A high specific conductance and a positive temperature coefficient were found in that investigation." Using a two-electrode apparatus, Savelsberg" electrolyzed various molten sulphide mixtures. He concluded that pure molten Cu,S and FeS were electronic conductors but that the mixtures exhibited some ionic conduction. In the present investigation, the specific conductance of the industrially important Cu-Fe sulphide mattes was measured as a function of temperature and composition in order to investigate the mode of electrical conduction and the structure of these molten mattes. An alternating-current circuit was used to eliminate the effect of any possible electrode reactions. Apparatus The Conductance Cell: Due to the high specific conductance of the systems studied (10' to 10" ohm-' cm-'), the classical two-terminal cell and Wheat-stone bridge apparatus could not be used. A four-terminal cell was developed in order to eliminate lead resistance, and an ac potentiometer circuit was designed to give rapid and sufficiently accurate measurements of the cell resistance. A diagram of the conductivity cell is given in Fig. 1. The molten matte is contained in a dense alundum crucible, and spectrographic graphite rods that dip into the molten matte serve as the four conductance terminals. Two of the graphite rods on opposite sides of the cell serve as current-carrying leads, and the other two graphite rods are null-current probes that detect the potential drop across the cell. These graphite rods are contained in silica tubes, and the lower constricted portions of the two silica tubes define the column of liquid whose electrical resistance is being measured. The electrical resistance of the broad ex-

Jan 1, 1956

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By N. K. Chen, R. B. Pond

IN the study of slip band* formation, there have been many examples to show that they do not always appear as lines traversing the entire crystal, but as segments whose ends seem to vanish in their path through the crystal. This characteristic appearance of slip bands has been witnessed under the optical microscope at various magnifications'-' and also under the electron microscope.' A typical example of this behavior seen with the optical microscope is shown in Fig. 1. However, the slip band studies were generally conducted on polished surfaces of single or poly-crystalline metals which had been previously deformed; i.e., the load was generally released so that the observation could be made. Any picture of slip bands so obtained can represent the surface phenomenon only in a static state of the strained material. The conditions prior to their formation cannot be definitely and clearly assigned. Thus, while a segmented slip band may suggest that slip is a growth process as supposed by the theory of the nucleation of slip,V he usual appearance of suddenly and fully developed slip bands around the crystal has generally been considered as a consequence of uniform shear of the entire slip plane akin to a cataclysmic process. Little clear-cut information is available with regard to the speed at which a slip band forms, its direction of motion, the geometry of its position with regard to its neighbors, and its dependence on orientation. A description is given in this paper of experimental apparatus by which the progressive formation of slip bands can be recorded while the specimen is undergoing deformation. Qualitative and quantitative data on the dynamic formation of slip bands will be presented with special interest concerning the propagation of slip bands, the spacing of slip bands, and their relations to strain hardening. Views on the formation of slip bands are discussed and a mechanism of the unit process involved in the formation of a slip band is proposed. Preparation of Specimens Single-crystal specimens of high purity aluminum (99.997 pct), 1/8 in. square in cross-section and 1% in. long in gage length, were made by the method of gradual solidification from the liquid state. Since no machining work could be introduced in preparation of crystals of such small size, a special mold was designed for casting them to final shape. The mold consisted of two, separate, high purity graphite blocks. Generally, 20 molds were packed together in one container so that 20 specimens could be obtained by one casting operation. This was desirable since it was possible by this method to obtain groups of crystals with similar orientations. The as-cast crystals were carefully clipped from the gate, etched, and homogenized for 24 hr at 600°C. They were then very gently polished using a 4/0 paper, re-etched, and finally electrolytically polished after the method previously described by Chen and Mathewson.6 The crystallographic orientations were determined using a back-reflection, Laue method. Tensile Testing and Photographic Method The tensile testing equipment for these tests was composed of a specially designed microtensile machine, microload cell and microclip gage with necessary appurtenances. The members of the microtensile machine consisted of three parts, as shown in Fig. 2. The chassis is equipped with an oil cylinder, A, and piston, the piston being part of the movable cross-head, B. Pressure in the oil cylinder is controlled and regulated by an external pneumatic-hydraulic cell, C, which is connected to the cylinder by a Vs in. high pressure copper tube. This cell is half filled with hydraulic oil and has a needle valve, D, on the oil exit side as well as a needle valve, E, on the gas inlet side. A quick-acting valve, F, as well as a pressure gage is provided for the gas side. The oil exits into the load piston on the microtensile machine. By connecting a tank of inert gas to the gas inlet, regulated pressures were provided over the oil so that the oil would leave the cell at a rate determined by the setting of the exit needle valve, the gas pressure, and the pressure of the oil in the load piston of the microtensile machine. With this pneumatic-hydraulic appurtenance it was possible to

Jan 1, 1953

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By William L. Crentz

In the past, Westmoreland County together with Fayette County produced about one-third of the bituminous coal mined in Pennsylvania. The Pittsburgh bed in Westmoreland County has furnished enormous quantities of coal to the by-product and beehive ovens, gas-manufacturing plants, and general industrial manufacturers over a wide area until about 20 years ago. Little attention was paid to the thinner beds because of the superior quality of the Pittsburgh. The approaching exhaustion of Pittsburgh coal will require accelerated-exploitation of these coals if Westmoreland County is to continue as an important source of bituminous coal, Much of the Pittsburgh coal in Westmoreland County is low-sulfur and requires no mechanical cleaning for the preparation of a metallurgical fuel. Even those areas where the sulfur percentage increased to a maximum of about 2 percent, a relatively easy washing operation usually produced a cleaned coal, which found ready acceptance by the coke industry. Davis reported the remaining recoverable reserves of the .Pittsburgh bed in Westmoreland County to be 255,439,000 tons as of January 1, 1937. Since that date, more than 100,000,000 tons of Pittsburgh coal has been extracted so that the time is not too distant when this important coal bed will be depleted. A study of the Pittsburgh bed in Westmoreland -County has not been made a part of this report as the remaining reserves of the coal can be used in coke making with a, minimum of preparation. The production from the Upper 'Freeport bed will increase as the supply of coal from the Pittsburgh bed diminishes, and as of the present time it supplies a substantial proportion of the county's coal output.

Jan 1, 1951

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By G. Wahl, H. Danilkewich, T. Mann

Developers of advanced mining projects face the challenge of how to craft a “Request for Proposal for a Feasibility Study” that will result in bids that are comparable and will lead to a successful execution of the study. Mining engineering consulting firms are challenged by “Request for Proposals” that may consist of a limited description of the Scope of Services and other items, which could present difficulties in the subsequent financing and/or development of the project. Changes in international disclosure requirements have also changed the landscape on how resources and reserves are reported by introducing new disclosure requirements and concepts such as qualified persons. This paper lays out a strategy for preparing a Feasibility Study “Request for Proposal” based on the experiences of a mining engineering consulting firm working on a diversity of projects around the world, and in light of the recent changes in international reporting standards for reserves.

Jan 1, 2002