Search Documents

By D. T. A. Symons, M. M. Kapnistos

"Gravity profiles were established over five known Middle Silurian pinnacle reef s in Lambton County, southwestern Ontario. The profiles were approximately 3 km long, with stations every 60 m. Four fairly recent technological developments were used which now make the gravity method relatively efficient and inexpensive compared to the techniques available two decades ago. These are: (1) a La Coste-Romberg model G gravimeter to measure the gravitational attraction with a sensitivity of 0.01 mgal; (2) a Sokkisha model B-2 semiautomatic engineers level to measure the station elevations with an accuracy of 0.5 cm; (3) a Huntec FS-3 hammer reflection seismograph to determine the overburden thickness to an accuracy of ± 7%; and (4) a modern microcomputer to process the data sets and mathematically filter the gravity values. Thus, two men can measure and analyze approximately 1 km of profile per day and obtain the residual gravity profile to an accuracy of ± 0. 05 mgal. Positive gravity anomalies of 0.17 to 0.72 mgal were observed along all five profiles that approximately delineate the dimensions of the known pinnacle reefs, which have an average height of 120 m, diameter of 1500 m and depth to top of 575 m. The relative ease of the gravity survey method makes it a cost-effective technique for hydrocarbon exploration in southwestern Ontario. IntroductionPinnacle reefs are important sources of oil and gas. Although the pinnacle reefs in southwestern Ontario are small, they may contain commercial pools of oil and gas because of their proximity to refineries. They are also useful for subsurface storage of gas to meet the winter surge in gas demand.At present, geophysical exploration for new pinnacle reefs is done primarily by relatively expensive seismic methods, which are also limited in southwestern Ontario by prohibitions on blasting. Gravity methods of exploration were attempted more than two decades ago in this region. (Pohly, 1954); however, the level of technology at that time made the method marginal in sensitivity and quite expensive. Several subsequent developments- gravimeters with greater sensitivity and operating ease, ""self-levelling"" levels for elevation control, hammer seismic reflection units for determining overburden thickness and portable microcomputers for efficient data analysis-have significantly improved the precision and cost effectiveness of the gravity method. Five known pinnacle reefs were selected in Lambton County, southwestern Ontario (Fig. 1), to test the effectiveness of integrating these developments to locate and define additional reefs. Isolated reefs were chosen to avoid the problem of the gravity effect s of one reef interfering with those of a neighbouring reef. The surveys were facilitated by choosing reefs with a concession road passing directly over them ."

Jan 1, 1980

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

By AIME AIME

ALL technical men who are planning to visit the Century of Progress Exposition in Chicago this summer-and all reports indicate that it will be worth visiting-should try to be there during Engineers' Week, beginning June 26. At that time most of the national engineering societies of the country will hold important meetings in that city. Engineers will thus have an opportunity not only to see the Fair at a time when special programs have been arranged for their benefit, but will have the opportunity to meet their professional brothers and to attend technical sessions of direct interest to them. The A.I.M.E. headquarters will be at the Stevens Hotel, and it will be to the interest of every Institute member who expects to attend the Fair at that time to secure his accommodations as promptly as possible. A request to the Chairman of the Chicago Section, A.I.M.E., or to the Secretary's office in New York, will bring a copy of the program as soon as it is available, together with any in- formation desired about hotel accommodations or other matters. The Chairman of the Chicago Section is J. R. Van Pelt, and his address is Museum of Science and Industry, 1525 East 53rd St., Chicago.

Jan 1, 1933

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

By Earl Hunner

IT is common knowledge that the iron orebodies of the Mesabi range lie nearly horizontal and are of trough or blanket-like types. These orebodies are from a few feet to several hundred feet thick and vary from a few acres in extent to the size of the largest one, at Hibbing, Minn., which is over 1 mile wide and 3 miles long. They are covered with sand, boulder and clay overburden and occasionally, shallow depths of ledge material, varying in total depth from about 20 to 200 ft. Large areas are not capped with overlying ledge material; the top of the ore lies directly underneath the surface material. Because of the comparatively great tonnage of ore, open-pit mining has made tremendous strides since the first open-pit ore was shipped from this range by the Merritt brothers, from the Mountain iron mine in October, 1892, and along with the great development of open-pit mining on the Mesabi range has gone a tremendous change in the character of equipment used.

Jan 1, 1930

By E. Barsky

"Theoretical notions of mass transfer processes in cascade separation of bulk materials have not been adequately developed as yet (Barsky M.D. 1980). In this paper we have derived linear difference equation of the second order for a cascade with initial feeding top any stage proceeding from mass exchange regularities. The solution of these equations has allowed us to determine quantitative dependences of the material distribution over the cascade stages, which serve the basis of the method of predictive estimate of the process results. We have also examined the model of the material distribution coefficient formation at individual cascade stages.We have checked the adequacy of this model to experimental data. It is noteworthy that the obtained theoretical results are phenomenological, i.e. they can be applied to the processes of separation of different physical nature, e.g. of isotopes, liquid media, gases, etc.INTRODUCTIONRecently, the processes of cascade separation of bulk materials have found broad application in various industries. They ensure a high separation efficiency and high-quality composition of final products. Although specialized literature gives serious attention to cascade processes [1], their theory is not sufficiently developed yet. To achieve optimal organization of this process, we examine mass transfer in a cascade gravitational classifier with stages of identical design."

Jan 1, 2016

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By L. F. Mondolfo, F. A. Crossley

The mechanism of grain refinement by the addition of small amounts of titanium, molybdenum, zirconium, tungsten, and chromium to aluminum was investigated. The results indicate that the grain refinement is caused by the peritectic reaction which, by transforming the intermetallic compound into crystals of aluminum solid solution, seeds the melt with nuclei above the freezing point of aluminum. THE feasibility of reducing the grain size of aluminum alloy castings by the addition of small amounts of titanium, zirconium, molybdenum, tungsten, columbium, boron, and chromium has been known for a long time, and the use of some of these elements as grain refiners is common practice in the aluminum foundry industry. The purpose of the present investigation was to determine the mechanism by which these additions produce the grain refinement. Asato et al., on the basis of extensive work on copper, antimony, and silver alloys, presented a theory of grain refinement based on the occurrence of the peritectic reaction. Briefly, this theory states that during cooling of the melt crystals of the primary phase form, which react peritectically with the liquid upon further cooling. The peritectic reaction transforms at least partially the primary crystals into crystals of the secondary phase, which then act as nuclei for solidification of the remaining melt. As the peritectic reaction takes place the primary crys- tals break in pieces, and each piece acts as a nucleus. Fine dendritic crystals which can easily break are the most effective for grain refinement. Sicha and Boehm," in investigating the refining effect of titanium on an AI-Cu alloy, concluded that TiA1, crystals serve as nuclei to initiate crystallization, but did not offer further information on the mechanism of refinement. Bonsack in the discussion of their paper suggested that refinement was due to clouds of some solid in the melt, probably TiO² which hindered grain growth. Eborall,' after studying the effect of titanium, zirconium, vanadium, tungsten, columbium, chromium, and boron on some alloys, concluded that the peritectic reaction was not an essential feature of grain refinement. Her conclusion was based mainly upon the observation that under her experimental conditions (sand casting) the Al-Cr alloys, which undergo a peritectic reaction, did not show appreciable refinement. Cibula" investigated the mechanism of grain refinement and reported that two types of grain refinement exist: 1—Grain refinement produced by restriction of grain growth by the concentration gradient mechanism proposed by Northcott.' 2— Grain refinement produced by the presence of particles in the melt, upon which the melt crystallizes easily. He further concluded that very marked grain refinement results from a combination of the two mechanisms. Since Tic was found present in aluminum alloys refined by the addition of titanium, it was identified as the nucleating agent. In the case

Jan 1, 1952

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By V. D. O’Leary

The Anaconda Co. has two economic uses for the drainage water from its underground mines in the district of Butte, Mont. One is the precipitation of copper, which the company has been accomplishing at the Leonard precipitating plant for many years, and the other is the leaching of the Berkeley pit discard, where millions of tons of leach material have accumulated. The acidic mine drainage water is an ideal leaching medium for the latter purpose, but the solids and colloidal material suspended in the water must be removed before it can be applied to the low-grade Berkeley leach dump. For this reason, it is important for Anaconda to have an efficient means of cleaning mine drainage. Such a means has been found and tested at one mine and is now to be incorporated in a new central pumping station the company is planning at the 3900-ft level of the Kelley mine. This plant is to be activated in early 1967 and will replace the antiquated four-lift High Ore mine pumping plant which was designed and installed before tailing backfill was adopted. The new plant will feature eight pumps with a total capacity of 8000 gpm in a single lift against a total dynamic head of 4100 ft. For the most efficient and economical operation of the plant it is imperative that all possible mud be removed from the drainage water before pumping.

Jan 9, 1966

By Khosrowshahi

A scientific approach to analysing grade control has been applied at a number of mining operations. By dividing the grade control process into the various stages of data collection and interpretation, errors can be identified using reconciliations of production against predictions. The merits of different mining styles in large and small open pit mines are examined.One factor in successful grade control is estimation of the expected ore loss and dilution. Empirical methods developed in two dimensions have been refined to enable 3D modelling of the effects on mineable grade and tonnage of varying the bench height, sampling orientation, and sampling Resolution.

Jan 1, 1992

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By N. A. Parlee, A. E. Lord

Measurements of the solubility of lead in liquid iron were made at 1550°, 1600°, 1650°, and 1700°C using two different methods, i.e., 1) liquid iron-liquid lead equilibration and 2) liquid iron-lead vapor equilibration. LEAD was long considered insoluble in liquid iron1. Today steels containing 0.15 to 0.35 pct Pb are used. One laboratory has found a solubility of about 0.5 pet in the 1600°C range. Recently Miller and Elliott2 gave 0.60 pct as the result of one determillation at 1540°C. Because these findings resulted from the

Jan 1, 1961

By Takahide Wakamatsu, Junji Shibata

Complex polymetallic sulfide ore deposits occur in Tohoku district, northern part of Honshu island, Japan. The ore is locally called "Kuroko” ( black ore ) and is compactly composed of fine grained sulfide minerals of such principal metals as copper, lead, zinc and iron. Currently one of Kuroko mill plants is producing such concentrates as copper, lead, zinc, pyrite, barite, and clay minerals, mainly employing differential flotation techniques. This paper describes briefly the progress of techniques in Kuroko processing over the past thirty years and also the present state of Kuroko processing and its challenges to be studied and overcome in the future.

Jan 1, 1989

By N Patzelt, T C. Logan, I B. Klymowsky

In 2003, NEWMONT MINING CORPORATION, the worldÆs largest gold producer, set out to prove that High Pressure Grinding Roll (HPGR) technology is sufficiently robust and reliable to be considered for the treatment of hard rock gold ores. In collaboration with POLYSIUS, a significant trial was conducted and 127 600 tonnes processed, successfully proving the HPGR capabilities on the Lone Tree Mine, Nevada ore û one of the most competent and abrasive ores in the industry. The success has led a number of mining companies to consider HPGRs for the comminution of gold and copper ores.

Jan 1, 2004

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017