Search Documents

This paper describes the experiences with the application of the Coal Mining Roof Rating (CMRR) System to South African strata conditions. Roof classification studies using the CMRR system were undertaken as part of a SIMRAC investigation into falls of ground in South Mean collieries. Colliery roof rating exercises were undertaking in a range of geotechnical conditions from shallow level coal seams under flat topography to workings with cover depths of greater than 300m A comparison is made between the CMRR and other Rock Mass Rating systems used to classify different roof geotechnical conditions. The need for geological discontinuity orientation, blasting and rockmass stress adjustments to the CMRR is discussed. The effects of acid mine water on strata weatherability and the need to incorporate immersion tests using acid mine water are also detailed. In addition limited correlation is given between CMRR values and other geotechnical factors such as joint trace length, joint shear strength, joint orientation, weatherability and roof damage due to horizontal stress. Taking cognizance of these observations, a concept of stress induced roof damage triggering is discussed.

Jan 1, 2001

By Fowler T. J

Examples are provided of discontinuity analysis at selected sites in central Victoria. Discontinuities are rock fractures of low tensile strength, including bedding, foliations and joints, which are analysed during rock excavation design, to quantitatively determine the defect orientations, spacing and lengths. Their analysis can reduce the cost of mining operation and improve safety. Extrapolation beyond the exposed face is required, although difficult without an understanding of the regional geology. For rock engineering purposes assumptions are commonly made that discontinuity characteristics are uniform throughout the rock mass, however this is often invalid, as rock masses have usually undergone large-scale deformation, exhibit anisotropy and inhomogeneity. Structural geologists are able to interpret large-scale deformation responses for the purposes of structural correlation and extrapolation. Examples of discontinuity analysis linked to regional geological assesment from sites in central Victoria, reveal that discontinuities exhibit similar characteristics in a range of rock types of different ages and composition. Spacing variations between individual sites are believed to be a result of local rock type differences.

Jan 1, 1997

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By S. Tan

A computer-oriented systems simulator (CMHS) has been developed for analysis of continuous materials handling systems. Special emphasis has been placed in the model on several features which are unique to these systems. These features include periodic pattern of material arrival from several sources, several types of material to be transferred, material dispatch processes, intermediate storage capacities, and multiple material destinations. Both the deterministic factors of the continuous material handling system such as the physical decomposition of the system and the scheme and schedule of its operation and the stochastic factors such as variations of material arrival, material pattern on the conveyor, and avail-abilities of the system elements are considered in the simulator.

Jan 1, 1988

By John G. Viets, J. Robert Clark

A multielement extraction system is being used successfully to provide essentially interference-free geochemical analyses to aid in gold exploration. The Methyl isobutyl ketone-Amine synerGistic Iodide Complex (MAGIC) extraction system separates Ag, As, Au, Bi, Cd, Cu, Ga, Hg, In, Mo, Pb, Pd, Pt, Sb, Se, Sn, Te, T1, and Zn from interfering geological matrices. Quantitative extraction of these elements is accomplished over a broad range of acid normality, making it possible to economically determine all 19 elements from a single digestion or leach solution. The resulting organic extracts are amenable to analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and flame atomic absorption spectroscopy (FAAS). For many years the principal shortcoming of ICP-AES was the complex spectral and stray-light interferences that were caused by the extreme variability of components such as Fe. Na, and Ca in common geological matrices. The MAGIC extraction allows determination of the extracted elements with enhanced sensitivity, from a virtually uniform matrix, by ICP-AES and FAAS. Because of its simultaneous multichannel capabilities, ICP-AES is the ideal instrumental technique for determining these 19 extracted elements. Ultratrace (sub-part-per-billion) determinations of Au and many of the other extracted elements can be made by graphite furnace atomic absorption spectroscopy (GFAAS), following back stripping of the extracts. The combination of the extraction followed by stripping of the organic phase eliminates 99.999% of potential interferences for Au. Gold determination by GFAAS from these extracts under the specified conditions yields a fourfold improvement in sensitivity over conventional GFAAS methods. This sensitivity enhancement and the interference-free matrix allow highly reliable determinations well into the parts-per-trillion range.

Jan 1, 1990

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By N. D. Ilankoon

"The use of thiosulfate as an alternative lixiviant for cyanide to treat complex refractory ores followed by the use of ion exchange resins (IX resins) for gold recovery has become an industrial reality. In this study, polyethylenimine (PEI) coated iron oxide magnetic nanoparticles (MNPs) were used to recover gold from the leaching solutions that consist of calcium thiosulfate, copper and gold. The gold loaded MNPs were easily separated from the solution using an external magnetic field. Proposing a novel adsorbent with characteristically easy solid-liquid separation, to recover gold from synthetic thiosulfate leaching solutions and gold elution and reuse of MNPs were the main objectives of this study. Adsorption isotherm studies revealed that the data fitted both Langmuir and Freundlich isotherm models equally well. The maximum adsorption capacity was 18.5 mg/g at pH 8 and 50?C. According to thermodynamic studies the physisorption process was exothermic and spontaneous. Gold and copper elution, and the regeneration and reuse of the nanoparticles were investigated and promising results were obtained. Different elution systems comprising sulfites, chlorides, glycine, EDTA (ethylenediaminetetraacetic acid) and sodium hydroxide were considered. Among them, EDTA for copper elution and NaOH for gold elution were the most efficient eluants. Regeneration and reuse studies revealed that the MNPs can be used for several cycles without significant performance loss. INTRODUCTION Although cyanidation has been used for gold leaching for more than 100 years, some major drawbacks associated with cyanidation have led to a quest for alternative lixiviants for gold leaching. Cyanide is ineffective in treating carbonaceous refractory ores as gold cyanide complex is adsorbed onto the native carbon in the ore itself known as preg-robbing. On the other hand environmental concerns associated with cyanidation drives the need for environmental friendly alternatives for cyanide. As of today, thiosulfate is known to be the most extensively studied and most promising alternative lixiviant for cyanide in both technical and environmental perspectives (Aylmore and Muir 2001, Oraby 2009)."

Jan 1, 2018

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

An Ore Reserves and Exploration System has been under continuous development at Mount Isa Mines Limited since 1970. The task of re-engineering the system has now begun, and the first stage is operational. This paper describes how the application of data base concepts, and table driving techniques has resulted in a design in which the input documents, validation procedures and file data content are redefinable by parameters, thus allowing the system to be tailored to suit varying geological Environments.

Jan 1, 1977

The results of iron ore exploration in Western Australia between '1961 and 1964 are outlined, with particular.reference to the Hamersley Iron Province. Exploration during: these three years has increased the known resources of the-,Statle from 275 million tons to almost 9,000 million tons of high- grade hematite ore. In addition, reserves of lower-grade .pisolitic limonite ore are-estimated to amount to 6,000 million tons. The origin and characteristics of the different types of ore is discussed,

Jan 1, 1964

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Na Wang, Chao Du, Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Niobium aluminides were directly synthesized by a sodiothermic reduction process of NbC15 - AlCb which was dispersed into LiCl - KCl - NaCl - CaCb melts. The melt supplied a homogenous reaction medium which was substantially beneficial to the co-reduction of Nb and Al to form niobium aluminides in situ. The reduction was performed at 500°C for 4 hours. The products were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The corresponding results indicated that niobium aluminides powders were successfully synthesized.1. IntroductionNiobium aluminides have received considerable attention as high-temperature structural materials, due to their high melting points, relatively low density, high strength, excellent oxidation and creep resistance [1-4]. Figure 1 shows that there are three intermetallic compounds in the Nb - Al binary [5], which includes Nb3Al (A15 structure, Cr3Si type), Nb2Al (D8b structure, cr-CrFe type) and NbAb (D022 structure, TiAb type). These niobium aluminides have been used in turbine blades or in stationary gas turbines [6-8]. However, despite their attractive features, the ir applications are still limited by the long and costly fabrication process [9, 10].Niobium aluminides were industrially fabricated by the mechanically alloyed process [11-13]. Traditionally, niobium is extracted from Nb2O 5 or K2NbF7 by a metallothermic reduction process while aluminum is produced by the Hall-Heroult process of Ah03 electrolysis. Based on the extraction of Nb and Al, respectively, niobium aluminides is synthesized by a mechanical powder alloying process. The present process for making niobium aluminides requires a set of complicated equipment, has high production cost and time consuming [14, 15].The purpose of this work is to present the simple, economic and direct synthesis of niobium aluminides powders utilizing a sodiothermic reduction from NbC15 - Al Cb dispersed into molten salts."

Jan 1, 2011

By G. W. Jones, G. S. Scott

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By G. S. Scott, G. W. Jones

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

Water quality standards for some of the substances likely to be discharged to natural waters by the mining industry are discussed. After briefly examining how uses of water can be affected by discharges, standards for suspended solids and turbidity, pH, and toxic materials are considered. Heavy metals are examined in some detail because of recent public concern regarding their discharge. Caution is given in connection with their analysis at the very low concentrations required for management of natural waters. Finally, the issues of what constitutes a water right concentration compliance breach, and the appropriateness of biological monitoring as a condition on a water right are raised.

Jan 1, 1986

By A. Hemami

In order to automate the operation of mechanical loaders it is essential to have a knowledge of the forces that act on the bucket and of the trajectory that the bucket should follow. A trajectory for the cutting edge of a bucket is derived from studies of the forces acting during the scooping phase. The proposed trajectory has a minimum energy consumption and is simple to automate. It is determined initially by setting to zero certain components of the resistive forces to the bucket motion which would otherwise result in unnecessary work and consequent energy wastage. The method for finding the appropriate trajectory is discussed on the basis of the properties of the material to be loaded and the loader size.

Jan 4, 1993