Search Documents

By V. Pouyafar

In recent years semi-solid processing of steel alloys has gain more attention among researchers. Production of high quality complex steel parts with higher mechanical properties is the final goal for all these researches. A thorough understanding of the flow behavior of the metal under investigation is the key for a successful process design. The material used in this research is M2 tool steel. The experiments were performed using a Searl-type concentric cylindrical rheometer which is specially designed for high temperature rheological measurements up to 1500 ºC. The rheological techniques were consisted of continuous cooling experiments and isothermal holding and also shear rate step change experiments for different solid fractions. Based on the rheological data a single phase thixotropic model has been derived and adopted to the measured data. The state of the microstructure has been applied through a structural parameter. The model fits well with the experiments.

Oct 1, 2011

By C. W. Volek, G. Mandl

Steam-injection tests in the field have shoum that heat transport into the oil/water region, ahead of the steam zone, may have a significant effect on the production process. Earlier theoretical work on reservoir heating by hot-fluid injection can be used to describe the growth of the steam zone, but only if heat transport from steam zone into oil/water region is neglected. It therefore became necessary to re-examine and extend the earlier theory. It was found that this theory ceases to be consistent with the physical model of the process at a certain critical time, tc, which depends on reservoir thickness, temperature, and quality of the steam. The critical time marks an important change in the heat flow across the condensation frovt: the heat flow, which is purely conductive during 0 < t < tc&apos; becomes predominantly convective at t = tc. Accordingly, at t = tc, the equation which governs expansion of the steam zone changes. On the basis of the new equation, an approximate description for the steam-zone growth during t > tc is developed by making use of upper and lower bounds for the exact solution of the problem. The boundary conditions for heat and mass flow inside the oil/water region are established, and a simple method of detennining the saturation at the downstream side of the condensation front is presented. Experimental results show that the theory gives an accurate description of steam-zone expansion before the critical time. At times near critical time, and also after critical time, experimental data show theoretical steam-zone volumes to be high. Even so, the accuracy of the calculated steam-zone volumes is sufficient for practical purposes. THEORY OF STEAM-ZONE GROWTH INTRODUCTION The engineering evaluation of steam-drive processes is based mainly on a mathematical description of reservoir heating by hot fluid injection presented several years ago by Marx and Langenheim.l This theory can be used to determine the growth of the steam zone,2 provided the flow of heat from the steam zone into the liquid zone ahead of the condensation front (Fig. 1) is neglected. Since we must expect, however, that heat transport into and inside the liquid region (the region between condensation front and production wells) will affect both the water/oil flow and the growth of the steam zone, it is necessary to re-examine and to generalize the Marx and Langenheim theory as applied to steam drive, which will hereafter be termed the "old" theory. Observations made in several field tests emphasize the need to study the heat flow across the condensation front (CF). On several occasions it was discovered that heat was transported in the liquid zone far ahead of the advancing CF, resulting in an early breakthrough of warm water. This seems to occur most often when high injection pressures are applied, when "wet" kONINKLIJKE/SHELL EXPLORATIE EN PRODUKTIE LABORATORIUM RIJSWIJK, THE NETHERLANDS SHELL DEVELOPMENT CO. HOUSTON, TEX.

Jan 1, 1970

By M. Dotto, T. G. Joseph, M. Curley

"Equipment selection is a key decision in mine planning. Equipment size affects decisions from pit size to the total operation cost. Particularly when replacing haulage fleets for long-life surface mining operations, mining operations focus solely on haulage productivity. Road width and specifically ramp width are significantly affected by an increase in hauler size in terms of overall strip ratio through required highwall set-backs or sterilizing of lower ore access due to required overlying ramp fill structures. In addition, in light of ever increasing regulatory and reporting emissions requirements, bigger equipment may not translate into lower emissions per tonne moved. This study analyzes hauler-scale impacts on aspects not currently incorporated into conventional mine planning, including expansion of roads to accommodate larger equipment, road layer thickness variation depending on hauler size, and fuel consumption and emissions. Results indicate that such relationships have a large impact on cost. Therefore, an expanded consideration of the capacities of increasing equipment size in mine planning is highly recommended. ¦ KEYWORDS Equipment selection, Grade resistance (GR), Haul road, Haul truck, Mine planning, Payload, Rolling resistance (RR), Total resistance (TR) RÉSUMÉ La sélection du matériel est une décision importante dans l’aménagement des mines. La taille de l’équipement a une incidence sur la prise de décisions, depuis la taille de la fosse jusqu’aux coûts totaux des activités. L’exploitation minière se concentre uniquement sur la productivité des moyens de transport, particulièrement lorsqu’il s’agit de remplacer les parcs de camions de transport dans les exploitations à ciel ouvert à longue durée de vie. La largeur des routes, et spécifiquement la largeur des descenderies sont considérablement affectées par une augmentation de la taille des camions de transport en termes du coefficient global de recouvrement qui dépend de la taille requise des parois (si les descenderies sont agrandies, les parois devront être creusées de haut en bas afin d’agrandir la taille du fond de la fosse). Il faut aussi pouvoir procéder à l’excavation des gradins les plus profonds de la mine et ainsi préserver l’accès à cette zone, ce qui pourrait devenir difficile si la quantité de stériles utilisés pour la structure des descenderies augmente et s’ils occupent une trop grande partie du fond de la fosse. En outre, au vu des exigences de plus en plus strictes en matière de réglementation et de déclaration des émissions, un équipement plus volumineux ne sera pas nécessairement synonyme d’une réduction des émissions par tonne déplacée. Cette étude analyse l’incidence de la taille des camions de transport sur des aspects actuellement non intégrés dans l’aménagement classique des mines, notamment la création de routes permettant le passage d’un équipement plus volumineux, la variation de l’épaisseur de la couche d’asphalte des routes en fonction de la taille des camions de transport, ainsi que la consommation de carburant et les émissions. Les résultats indiquent que ces relations ont des répercussions importantes sur les coûts. Ainsi, on recommande d’accorder une attention accrue aux capacités d’augmentation de la taille de l’équipement dans l’aménagement des mines. ¦ MOTS CLÉS aménagement des mines, camion de transport, charge utile, résistance au roulement, résistance due aux rampes, résistance totale, route de transport, sélection du materielINTRODUCTION Over the past five decades, the mining industry has progressively attempted to increase production rates through the use of larger haulage equipment. Each new generation of mine is designed to operate with the most recent and often bigger equipment iteration, while older mines are re-evaluated to keep pace with upgraded mixed fleets. Whereas production gains are often realized with larger equipment, there are additional aspects to consider when evaluating the feasibility of mo"

Jan 1, 2019

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By J. R. Montgomery, T. A. Phillips, F. Blackham, D. J. Adams

Underground water, whether it is a mine seep, in situ leach solu­tion, or a pollution plume, is difficult to track and monitor. Monitoring wells are costly to drill and may be placed in the wrong spot. This report describes a test of an electromagnetic technique to track acid water draining from the Midnite Mine near Spokane WA. The tests successfully mapped the path of acid mine drainage being collected at the mine from two seeps. Several small side branches flowing to smaller seeps and a mix­ing zone where relatively clean water mixed with the acidic water, were also mapped. The study has changed previous opin­ions on the flow of water through the site and will be used as a basis for future site remediation planning.

Jan 1, 1996

A new two-metre column self-heating test procedure has been developed at the University of Queensland, which clearly shows the hot spot development phases that take place in bulk coal self-heating. The column results provide a more reliable indication of the self-heating propensity of coal than small-scale index tests. At the same time, off-gas evolution patterns associated with hot spot development are obtained, including the recognition of hydrogen evolution from oxidation at temperatures less than 80¦C. Subtle differences in off-gas evolution from self-heating between gassy and gas-drained coal are also apparent. This new approach to coal self-heating assessment offers an opportunity to further the understanding of the complexities of spontaneous combustion and will enable more accurate risk assessment for the coal industry.

Jan 1, 2005

By W. C. Knopf, G. Samsel

For several years International Minerals & Chemical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large- scale plants. Natural potassium is composed of three isotopes -K39, K40 and K41. Five other isotopes, artificially produced, have been detected. In natural potassium only the K40 isotope, with a half life of 1.4 x 109 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes.

Jan 10, 1958

Of the energy resources present in Australia, coal and uranium are by far the largest. These two resources ap- pear sufficient to satisfy Australia&apos;s energy needs beyond the immediately foreseeable future and long after the natural petroleum resources are exhausted or have ceased to play a significant role. By that time, coal could be converted in plants of very large size to synthetic liquid and gaseous fuels which will be used as substitutes for pet- roleum fuels, particularly for transport. The basic role of uranium will be to supply electricity from nuclear power stations for heat and power requirements, thereby freeing non-coking coal largely for conversion purposes. The establishment of these enterprises will require a massive national effort and a high degree of co-ordination at the planning stage.

Jan 1, 1975

(This list. includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. A complete list will he found in the Year Book mailed with this Bulletin. Another Honor Roll is maintained in the reception room of the Institute.) ALDEN, HERBERT W., Lieutenant-Colonel, Ordnance Dept. ALDER, ALFRED; Engineers&apos; Reserve Corps. ALFORD, NEWELL G., Sergeant, Bureau of War Risk Insurance, Headquarters 84th Division. AMBLER, HARRY A., Lieutenant, 30th Infantry. ANDERSON, GEORGE K., JR., Sec. C, 1st Co.; 3d Officers&apos; Training Camp. AYER, -FRANK A., 1st Lieutenant, 43d Squadron, 3d Prov. Regiment, Aviation Camp.

Jan 3, 1918

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By K. J. Reid

A historical background of the development of automated material balance packages is presented including a summary of currently available packages and a description of the present work at the Mineral Resources Research Center of the University of Minnesota. A brief mathematical statement of the problem is given and solution techniques discussed. The problems and difficulties normally associated with material balances, both hand calculated and computer calculated are described. Several aspects of the available material balance packages as related to the "user/computer" interface are evaluated in detail. Elements of the material balance packages that affect the solutions are examined and the relative performance of the main packages on specialized problems presented. Finally, areas associated with automated material balances that require further work before computer packages can be widely used in industry are outlined.

Jan 1, 1982

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By Li Maolin, Cui Rui, Wang Guanghui

"As the stirrer speed directly affects the motion of grinding media, and hence the interactions with material particles to be ground, the rotation speed of a stirred mill is well recognized as one of the most important factors affecting the grinding performance. In this work, the effect of stirrer speed on grinding performance in terms of grinding rate and grinding energy efficiency was quantitatively investigated. Batch wet grinding tests of quartz powder at different stirrer speeds were performed, using a self-made horizontal stirred mill with alumina balls as grinding media. Grinding time, operating power and the sizes of ground product were recorded to analyse the grinding performance. The test results showed that grinding processes followed the first order grinding kinetics. The grinding rate constant increased with the increasing stirrer speed. Based on the grinding kinetics, the grinding energy equation was established. The energy utilization coefficient in the energy equation can be used as an indicator of energy efficiency. The energy efficiency decreased with the increasing stirrer speed. Quantitatively, with the stirrer tip speed increasing from 4.25m/s to 9.35m/s, the grinding rate constant was improved by 441.47%, whereas the energy utilization coefficient was decreased by 39.35%. The grinding rate constant and energy utilization coefficient can be used to evaluate the grinding performance when the grinding conditions need to be adjusted. The adjustment of grinding conditons would be optimal when grinding rate get significant improved with little decrease of energy efficiency."

Jan 1, 2014

By Parfitt RL

A quarter of the North Island, New Zealand is covered by weathered volcanic tephras of mainly andesitic and rhyolitic compositions. Rapid weathering of basic volcanic glass and slower weathering of acidic glass have produced short-range order alumino-silicate clays such as allophane. Although amorphous to x-rays they have a high degree of local structure. Allophane comprises hollo spheres of approximately 40 diameter and 7 X wall thickness. This small particle size and morphology gives a very high surface area (up to 800 m2/g). Ferrihydrite is another short-range order clay of similar small size and high surface area; it has ò formed from the rapid oxidation of water containing ferrous iron derived from volcanic rocks. The quantity of allophane present in tephra depends upon the climate, the nature of the volcanic glass and the time it has weathered. In New Zealand highest amounts (-50%) occur in beds of andesitic ash deposited on old ignimbrite surfaces with mean annual rainfalls >1600 mm. Both allophane and ferrihydrite will react with oxyanions, such as phosphate, arsenate or borate, and remove them from solution. Other anions such as fluoride also react with aluminium sites on the mineral surface. At NZ Soil Bureau, Department of Scientific and Industrial Research (DSIR), New Zealand, techniques have been developed for granulating allophane to enable it to be used to remove pollutants from solution without dispersion into the liquid phase. This granulated allophane can be used to remove phosphate from sewage effluent or fluoride from tap water without having a sedimentation stage to remove the clay.

Jan 1, 1987

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

In-stope long hole drilling (face parallel drilling) is a new technology currently being applied to shallow dipping (

Jan 1, 2003