Search Documents

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

By J. E. Jacoby

Scrap recycling has become an increasingly important source of metal units for the aluminum industry during the past 25 years. Aluminum scrap from the manufacture and recycling of cans, automobiles, buildings and other products has created an industry that melts these products and delivers the metal in molten or sow form to companies that make cast parts or fabricated products This rapidly developing recycling industry has contributed a large number of severe (Force 3) molten aluminum explosions (25) with associated fatalities (19) to the Aluminum Association data accumulated during the past nineteen years. The explosions that occurred in recyclers plants represent 17% of the total explosions, 33% of the Force 3 explosions and 37% of the fatalities reported. These explosions can be prevented! This paper will identify causes of these explosions and procedures that can be used to prevent them.

Jan 1, 2000

By Wayne A. Sadik

The mine ventilation system of the Henderson Mine provides a case study of designing and maintaining high-quality respirable air in a large underground mine with over 200 units of diesel-powered equipment. This system was designed with concern for minimizing exposure to personnel of siliceous dust, diesel exhaust, smoke, and potential fire hazards while optimizing general environmental air quality throughout the multilevel/multiheading operation. As a relatively new operation, the Henderson Mine incorporates a modern ventilating plant and mine de- sign as well as state-of-the-art technology where appropriate. Two main ventilation shafts approximately 2,300 ft (701 m) in depth (one intake, one exhaust) will handle 1.8 million cfm (850 m3/s) of air circulated throughout 60 miles (97 km) of drifting, providing the ventilation requirements for more than 25,000 diesel horsepower (18,642 kw) underground.

Jan 1, 1980

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By R. V. Ramani, S. Tan

A computer-oriented systems simulator (CMHS) has been developed for analysis of continuous materials handling systems. Special emphasis has been placed in the model on several features that are unique to these systems. These features include periodic pattern of material arrival from several sources, several types of material to he transferred, material dispatch processes, intermediate storage capacities, and multiple material destinations. Both the deterministic factors of the continuous material handling system, such as the physical decomposition of the system and the scheme and schedule of its operation, and the stochastic factors, such as variations of material arrival, material pattern on the conveyor, and availabilities of the system elements, are considered in the simulator. The application, of the model is demonstrated through a study of an underground conveyor belt network serving long- wall and continuous miner sections.

Jan 1, 1990

By A. W. Hall

A neutron meter was developed for monitoring the sulfur content of coal streams. Neutrons from 80 micrograms of californium-252 penetrate the coal, producing thermal neutrons that are captured by atoms of elements present in the coal. The excited atoms emit prompt gamma rays with energies characteristic of the capturing element. These gamma rays are detected with a 6-by 7-inch sodium iodide detector and processed by electronic equipment to produce a gamma ray energy spectrum of the elements. Tests of the meter at a commercial coal preparation plant showed that sulfur in moving coal can be determined to a precision of 0.05 percent sulfur within 2 minutes. Based on this report by the Bureau of Mines, reliability of the coal-handling system proved inadequate for long-term operation, however, and improvements are planned.

Jan 1, 1975

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By Raymond A. Bradbury

The first diesel-powered Scooptram has now been in service for 21/2 yr at the I-C mine of Martin County Coal Corp. It has become the workhorse of the operation, being used around the clock many days. The fleet of nine 20-ton capacity Teletrams used behind three Jeffrey Heliminers now have more than 1 1/2-yr experience in the Coalburg mine. They have been exposed to some difficult conditions which, include steep grades, water, mud, and rutted roadways. These units have proven to he both rugged and powerful. The safety components and shutdown systems make these haulage units very safe for underground coal mines. A clean-burning engine, a satisfactory exhaust conditioning system, and good ventilation are the keys to maintaining a safe and healthful atmosphere for the underground operators and other employees.

Jan 1, 1976

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

By N T. Byrom

This paper is essentially in two parts. It describes how risk assessment fits into the overall framework of the activities required to control risk effectively within an occupational health and safety (OH&S) management system. It then goes on to describe the assessment of an OH&S system by the process of auditing.

Jan 7, 1996

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

By Tobias U. Papst

The German Ruhrgebiet is slowly transitioning into a post-mining state. It has been subjected to industrial-grade hard coal mining operations for more than 150 years. Due to a political decision, German hard coal mining will come to an end in 2018. By then the surface will have subsided up to 20 meters. After all mining activities in the area have ended, there will be no need to maintain the current mine water level. Accordingly, the company operating the last remaining coal mines has decided to let the water level rise to an as yet undetermined level. Alongside other issues that may be caused by rising groundwater levels, the protection of the area?s drinking water supply is of utmost importance. This notion is also represented by European and German law. The primary intent of the applicable laws is to protect the health of the citizenship. This means protecting ground water that may be used by humans from being contaminated by the mine water. This paper outlines the consequences of European and German legislature on mining aftercare using the example of one of Europe?s largest agglomerations.

Jan 1, 2014

By Roger Holmberg, William Hustrulid

Swedish cautious blasting techniques were used to excavate a room at the CSM Experimental Mine in Idaho Springs, Colorado,as part of a ONWI/DOE sponsored nuclear waste disposal research program.

Jan 1, 1981

By Irving Hale

The superiority of electric power for mining purposes was recognized in a general way as soon as the electric motor be-

Jan 1, 1897

By A N. Gupta, C Joginadham, P Shiva Shankar

Cast boosters made with pentaerythritol tetranitrate(PETN) and trinitro toluene(TNT) give high velocities of detonation and are sensitive to initiation even under high pressures. However, the manufacture of the same involves heating of TNT to its melting temperature and mixing of dry PETN in it.

Jan 1, 1996