Search Documents

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.' This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987

By Andre Thess, Jurij Kolesnikov, Christian Karcher

"During the motion of molten metal under external non-homogeneous magnetic field the induced electric currents produce Lorentz body forces in the opposite direction to the flow, causing deformation of velocity profile, vortical structures, and adding a pressure drop across the magnetic field. The same Lorentz force acts on the magnet system. We analyse these phenomena in metallurgy, namely, at molten metal pumping, stirring, continuous casting, and in contactless Lorentz force flowmeter (LFF). Experiments with liquid metal alloy, including direct measurements of Lorentz forces, velocities, and flow structure visualization were conducted. Based on this study the industrial prototypes of LFF systems were designed, built, and tested in a secondary aluminium production. A molten metal flow at high temperature (700°C-850°C) can be effectively measured. The LFF technique method allows measuring precisely the volumetric and mass flow rates linked with Lorentz force, and the mass accumulated within production process.IntroductionThe present work demonstrates the development of a non-contact electromagnetic system for measurement of a liquid metal flow. Our approach embodies the Lorentz force velocimetry [1-6] technique which is physically based on a measurement of the force acting on an external magnet system the field of which interacts with the flow. This force is exactly equal to the braking Lorentz force induced in a flowing conducting fluid. In what follows a measurement system based on the Lorentz force velocimetry principle. For monitoring and controlling the production process it is desirable to measure continuously the mean velocity of the liquid metal in order to deduce the mass-flux and volume-flux from it. The form and dimensions of the magnet system are in agreement with geometry of the operating channel. We consider here a version of magnet systems in a composition of permanent magnets.The LFF possesses a number of advantages which make it attractive for the measurement of flows in hot and aggressive melts. The relation between the measured force and the desired volumetric flow rate is often linear (for closed channel or at a constant liquid metal level in open channel). For the converting of the measured force into volumetric and mass flow rate we should know the calibration factor. The calibration factor is independent of the viscosity and density of the liquid metal and depends only on the magnetic field magnitude, the electrical conductivity of the liquid metal and the geometry of the channel in which the liquid metal flows. In aluminium production, for instance, there exists a number of standard alloy compositions having welldefined conductivities for which the calibration factors can thus be tabulated. We consider below consistently effects in liquid metals arising under influencing magnetic field, construction principle of LFF and measurements of metal flows at industrial conditions."

Jan 1, 2011

Professor G.T. van Rooyen has guided the Department of Materials Science and Metallurgical Engineering at the University of Pretoria in South Africa for the past 32 years. During this period, 54 masters' degrees have been awarded in the Department, and 17 doctorandi promoted. He has also made a major contribution to industry by his incisive analysis, relevant and practical synthesis, and his exceptional talent in innovative design. He is still active in fracture analysis, thermal fatigue, weld simulation transformation kinetics, and fracture mechanics, and continues to contribute to a better understanding of metallurgical problems encountered in practice. He has advised many companies, and has received many honours and recognitions.

Jan 1, 1994

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

The paper discusses the improvements achieved after an external sparger flotation column was installed as a final cleaner at the Northam Platinum Ltd. UG 2 concentrator in South Africa. It further discusses the improvements achieved after the conversion of a conventional flotation column, utilized as cleaner in the Merensky concentrator, to an external sparger flotation column. Finally, the application of the above knowledge in the design and commissioning of an external sparger flotation column as final cleaner in the furnace slag concentrator, is also discussed. 1. FINAL CLEANER AT THE UG 2 CONCENTRATOR The MF2 designed UG 2 concentrator is processing 75 000 tonnes run of mine ore at a head grade of 4.0 g/t 3PGM+Au and a feed Cr2O3 concentration of 28 %. Since commissioning of the plant in 2001, Cr2O3 in final concentrate amounted to approximately 5 % of the total mass. Although final concentrate produced from the UG 2 concentrator is blended with final concentrate obtained from the Merensky concentrator before smelting, blended Cr2O3 values in excess of 1.6% lead to difficulties in the subsequent smelting process. Several options for reducing the amount of Cr2O3 in final concentrate have been evaluated namely:- ? Differing types of depressants at various dosing rates. This test work did not reduce the amount of Cr2O3 reporting to final concentrate by any significant extent. ? Reduction in mass pull to minimize the entrainment of Cr2O3 in the concentrate stream.. This process change had a detrimental effect on PGM recovery. Conclusions were drawn that conventional mechanically agitated flotation cells could not achieve the required selectivity without sacrificing PGM recovery. As a consequence an alternative mechanism needed to be incorporated for the final cleaning of PGM concentrate.

Jan 1, 2007

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick's second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method' are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5' could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5' or Ag'lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5' and 0.6 N HNO3 solution for the A"'), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5' atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953