Search Documents

By M. A. Dayananda, R. E. Grace, P. F. Kirsch

Ternary diffusion experiments were carried out at 750°C with vapor-solid diffusion couples in single-phase copper-rich Cu-Zn-Sn alloys. The Philibert-Guy method was used to calculate intrinsic diffusion coefficients at compositions corresponding to the plane of inert markers imbedded in the diffusion couples. Inter diffusion coefficients were determined at common composition points of intersecting diffusion paths. Intevdiffusion coefficients were also obtained at compositions corresponding to maxima in the tin concentration pvofiles Relations between the interdiffusion coefficients and the expansion of vapor-solid diffusion couples are described in detail. Such relations permit the calculation of constant interdiffusion coefficients in binary couples from expansion data directly. In ternary couples expansion data provide an additional constraint on the interdiffusion coefficzents. ThE phenomenological analysis of diffusion in ternary solid solutions has been developed extensively, and various approaches taken in the determination of diffusion coefficients have been reviewed recently by Guy et al.' Finite,' semi-infinite,3 and infinite4 diffusion couples have been used in studies of ternary diffusion, but most of the work has been done with infinite diffusion couples. Semi-infinite diffusion couples3 (vapor-solid couples) have been used to determine both intrinsic and interdiffusion coefficients in the Cu-Zn-Mn system, in which two diffusing species, zinc and manganese, were supplied from the vapor phase. If only one component has a sufficiently high vapor pressure to be supplied from a vapor source, vapor-solid diffusion couples may still be used. In this case the boundary conditions at the gas/solid interface may be governed by partial equilibria rather than by virtually complete equilibrium between the phases. In the present work diffusion measurements were carried out at 750°C with vapor-solid couples of Cu-Zn-Sn alloys. Only zinc was transported between the vapor source and the diffusion disks, because the vapor pressures of both copper and tin are at least 108 lower than that of zinc. Both intrinsic and interdiffusion measurements were made at several compositions. A secondary objective was to relate expansion of the diffusion couples with the interdiffusion process. Such measurements for binary couples yield average values of the interdiffusion coefficients over composition increments. In ternary diffusion couples ex- pansion data provide an additional constraint on the interdiffusion coefficients. COMPOSITION-DEPENDENT INTRINSIC AND INTERDIFFUSION COEFFICIENTS As shown by Philibert and GUy5 the determination of intrinsic diffusion coefficients in a ternary system requires two independent diffusion couples containing marker planes with identical composition. In the case of vapor-solid couples such a requirement torresponds to two couples set up with the same vapor source exposed to two diffusion disks of different composition. Inert markers placed initially on the disk surfaces become imbedded during diffusion. If the pair of couples exhibits appreciable marker burial with marker planes of virtually the same composition, the intrinsic diffusion coefficient may be evaluated at the composition of the marker planes. Fig. 1 is a schematic diagram of the concentration of of a Cu-Zn-Sn ternary vapor-solid couple after diffusion of zinc from a vapor source into a binary Cu-Sn alloy. The areas, Ai correspond to the cumulative intrinsic fluxes of the three diffusing species across the marker plane:5 where Ji is the intrinsic flux of component i, t is the diffusion time, and D3i are the intrinsic diffusion coefficients. For the determination of interdiffusion coefficients a pair of diffusion couples with intersecting diffusion paths is needed. At the composition point of intersection (C1, C2) the coefficients are evaluated from the equation:3

Jan 1, 1969

By David Cornell, Yusuf K. Sukkar

The fundamental differential equation for fluid flow has been rearranged, integrated numerically for natural gases, and the results presented in tabular and graphical form suitable for the direct calculation of vertical gas flow problems. The integration is rigorous except for the use of a constant average temperature. Both static and flowing bottom-hole pressures may be calculated by (his method without resort to trial and error procedures. INTRODUCTION Bottom-hole pressures can be determined either by direct measurement with a bottom-hole pressure gauge or by calculation. Since measurement with a bottom-hole pressure gauge is costly, calculation of bottom-hole pressures is to be preferred when possible. Calculation involves knowledge of the wellhead pressure, the properties of the gas, the depth of the well, the flow rate, the temperature of the gas, and the size of the flow line. These quantities must be combined in a suitable equation for vertical flow. Several equations have been developed for the purpose of calculating gas flow through both horizontal and vertical pipes1,2,4,5,6,7,8,9 These equations all have the basic differential equation for flow as their starting point. They differ only in the assumptions which are made in order to simplify the integration step. The bottom-hole pressures calculated using any of the better known equations are in good agreement with bottom-hole pressures calculated by a more rigorous but considerably more tedious stepwise integration method. All of these methods, however. require a trial and error solution for the calculation of flowing bottom-hole pressures. The purpose of this paper is to present a method which provides a direct solution of static and flowing bottom-hole pressures without use of a trial and error solution. At the same time the method involves fewer simplifying assumptions than any of the previous methods used, except lor the lengthy stepwise method. The derivation of any practical flow equation begins with the basic differential equation which is rigorous for almost all flow problems. The five terms in Equation 1 represent the potential energy, the potential energy of position, the kinetic energy, the shaft work done, and the energy losses due to motion of the fluid respectively. Equation 1 reduces to Bernoulli's theorem for the case of horizontal flow of an incompressible fluid, no work done, and no energy losses due to friction. In the present case, the term (v) (dv)/(g,.) can be shown to be quite negligible compared to the other terms, and is therefore neglected in the derivation. The term — dws includes work done by a pump or turbine in the system and is zero in this case. The frictional losses in the pipe are included in the term — d(lw) which is expressed in terms of the Moody friction factor as in Equation 2. (f) (v2) (dL) d(lW) = (f)(V2) (dl)/(2) (g) (d) The specific volume of a gas can be expressed in terms of the temperature, pressure, molecular weight, and compressibility factor. The velocity of the gas can be expressed in terms of the weight rate of flow, the specific volume, and the dimensions of the pipe.The reduced pressure Pr is to be used because z can be expressed as a function of Pr and Tr alone for most natural gases:

Jan 1, 1956

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication' a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950

By H. P. Kang, Y. J. Feng

The hard roof in underground coal mines is generally considered as a main cause that induces disasters in working faces and entries, such as rock burst and windblast. Hydraulic fracturing technology is an effective approach to weaken hard roof to reduce ground pressure and control rock burst. The state and achievements associated with hydraulic fracturing technology applied in Chinese coal mines are summarized in this paper. Theories related to hydraulic fracturing are of the essence in fracture design to determine the fracture initiation and propagation pressure and predict the geometry and the characteristics of hydraulically induced fractures. Initially, theory of elasticity was employed to determine the breakdown pressure for a vertical borehole where the rock medium is assumed to be elastic. However, porosity and pore fluid have an influence on the borehole breakdown pressure, and then the poroelasticity theory was applied. Arbitrary deviated boreholes in practice are rather common and the maximum tensile stress criterion was employed to determine borehole breakdown pressure. The effect of natural crack in the rock medium on the initiation pressure has been taken into consideration through fracture mechanics. Meanwhile, considerable achievements have been made on hydraulic fracturing tools and equipment, and a set of mature hydraulic fracturing technologies for hard roof control are available. Some comprehensive investigations on the hydraulic fracturing for hard roof weakening are presented, and successful field applications in the Jincheng and Luan coal mining districts are introduced. Finally, the unsolved problems related to hydraulic fracturing are also put forward.

Jan 1, 2015

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable cases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of uses produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.

Jan 1, 1931

By Shozo Saito, P. A. Beck

Mettrllographic and X-ray diffraction study of Cb-Co alloys in the Composition range of 7 to 33 nt. pct Cb, after annealing at 1175 °', showed that near 25 al. pct Cb on MgNi,-lype hexagonal Laves Phaseexists in a narrow composition range, and that an MgCl- type cubic Laves Phase occurs between approximately 27 and 32.6 ut. pd Cb. Lattice parameter and density measures indicated that, in both phases. the deviations from proper Loves sloichimetry result from the substitution of cobalt atoms for some 0f the columbium atoms. Tlle same phases occurant 1000'C, together with an additional phase of unknown structure, which appears between the hexagonal Laves phase and the cobalt-bose terminal solid solutions KOSTER and Schmid' identified a phase corresponding to the composition VCo,, and more recently the crystal structure of this phase has been determined.' In the Ta-Co system Korchynsky and Fountain recently found two intermediate phases at the composition Taco,, one of them metastable. In contrast to the V-Co and the Ta-Co systems, in the Cb-Co system no intermediate phase has been found4 at the composition CbCo,. The present investigation was undertaken in order to reexamine the question of the existence of such a phase. EXPERIMENTAL PROCEDURE Twelve alloys were prepared by arc-melting in a water-cooled copper crucible under helium atmosphere. Electrolytic cobalt and 99.9 pct pure colum-bium powder have been used as starting materials. It was found that melting losses can be reduced by compressing the colunlbium powder in the form of thin pellets before melting. For the alloys used the melting losses were not higher than 1 pct. The intended compositions of all alloys and the chemical analyses of three of them are given in Table I. Specimens from all alloys were annealed in evac- uated fused silica tubes at 1175°C for 3 days and quenched in cold water. A second set of specimens of most alloys was annealed at 1000°C for 7 days and then quenched in cold water. The annealed and quenched specimens were examined metallographically, using the following etchant: 60 pct glycerine +20 pct H,NO, + 10 pct HF + 10 pct water. Powder specimens for X-ray diffraction were prepared by crushing annealed solid specimens in a mortar. Alloys containing 27.3, 28, 29.7, and 32.6 at. pct Cb annealed at either 1175" or 1000°C were very brittle and it was found unnecessary to reanneal the powders. However, alloys containing 24.8 at. pct Cb, or less, especially those annealed at 1000°C, were much less brittle and re-annealing was required to remove the strains present in the crushed powders. In each case reannealing was done at the same temperature at which the corresponding solid specimens were annealed and it, too, was followed by quenching in cold water. In many instances X-ray diffraction patterns were also taken of the polished and etched solid specimens and compared with the corresponding X-ray diffraction patterns obtained with powders. The X-ray diffraction patterns were taken with an asymmetrical focusing camera, using CrK radiation. For precision lattice parameter measurements some X-ray diffraction patterns were taken with a symmetrical focusing camera, again using CrK radiation. EXPERIMENTAL RESULTS A microscopic examination of the alloys annealed at 1175°C revealed that the alloy containing 25.5 at. pct Cb was composed of a single phase, but that the 24.8 at. pct Cb alloy did contain a small amount of a second phase, identified by means of X-ray diffraction as having a fcc structure, undoubtedly the terminal solid solution based on cobalt. Apart from the few very weak lines corresponding to this minor phase, the X-ray diffraction patterns of these alloys could be well interpreted in terms of a MgNi,-type hexagonal Laves phase structure. The indexing of the X-ray diffraction pattern, Table 11, yas based on the lattice parameter values a, = 4.740A and c,

Jan 1, 1961

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By Y. C. Liu

THE existence of mechanical twins in bcc metals has long been known. With recent intensive interest in the mechanism of twin formation and its role in plasticity and crack initiation, a study of the general Characteristics of twin intersection appears pertinent. The scope of the present note will be limited to the crystallography of the twin intersections of (112) twins, without consideration of its mechanism, movement of atoms, crystal structure, or the strain energy involved at such an intersection. The twinning elements of (112) twins are considered to be K1 = {112}, n1 = (111) and K2 = {112}, n2 = (111) with a twin shear of 0.707. The crystallographic features of twin intersections have been worked out in detail by Cahn.1 The present work applies the general principles postulated by Cahn to the intersections of (112) twins. The basic conditions for the twin intersection are: 1) The trace of crossing (A) and the secondary (C) twins in the planes of the crossed twin (B) must be parallel. 2) The direction (n1) and magnitude (s) of shear must be identical in the crossing and secondary twins. Also the sense of shear must be the same. These two conditions have to be fulfilled in order to maintain geometrical continuity at the twin interfaces. Fig. 1 shows the perspective representation of how these two conditions are fulfilled at the intersection. This type of intersection will be named Type-I. It is the purpose of this note to point out the existence of another type of intersection, Type-II, as shown in Fig. 2. In this type of intersection, the crossing twin A remains straight and the crossed twin B has been bent. The two conditions laid down by Cahn must also be met. This leads to the following corollary conditions: 1) The interface between twins B and C must be parallel to the twin habit of crossing twin A. 2) n1c must be parallel to n1A. 3) The twin shear (s) of twin C must be exactly equal to and in the same sense as that of crossing twin A. Thus, in order for the Type-II intersection to take place, the twining elements of secondary twin C must fulfill the above three conditions with respect to crossing twin A. Let K1 of crossed twin B be (112). All indices of the matrix can therefore be converted into new in-

Jan 1, 1963

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.'-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4'5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,'-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By J. T. Ryan

SiR Humphry Davy's epoch-making treatise delivered on Nov. 9, 1815, before the Philosophical Society of London, first announced and demonstrated a flame safety lamp for detecting methane in mine air. Coal mining was known in England as early as 1180, more than 600 years before the advent of a safe lighting and gas-detecting appliance. Mining, no doubt, took place first in outcrop coal, and danger from gas did not become apparent until the workings became deeper and more extensive. Davy's lamp did much to increase the safety of miners, and a modified Davy lamp is still widely used for detecting the presence and approximate amount of combustible gas in mine air. No factor in coal mining has improved more rapidly during the past 15 years than safety measures. This progress came about not only as a result of the workmen's compensation laws now in force in most of the states of the Union, but because the research work of the U. S. Bureau of Mines had demonstrated some dangers incident to coal mining which were not considered to be serious matters prior to that time. Electric power and explosives are necessary but potential hazards in American coal mines. A general mechanization program is now under way, while the mines are growing deeper and more extensive. Consequently ventilation problems are more complex and a demand has been created for positive detecting devices for carbon monoxide as well as methane. Scientists and manufacturers, working hand in hand during the past 10 years, have invented and developed appliances which make systematic and effective examination of mine air possible. The object of this paper is to describe briefly the approved testing devices in use today, with the hope that they may lead to the saving of life. Two Groups of Dangerous Coal Mine Gases Dangerous coal mine gases may be placed in two groups: (I) those that are dangerous because of their explosive properties, and (2) those that are dangerous because of their toxic properties. Methane (CH4) is the important gas of the first group, and in so-called gaseous mines constantly exudes from the coal and rock; it may accumulate and form an explosive mixture. The explosive range of methane-air mixtures is well defined. The low limit is 5 per cent., the high limit 15 per cent., and the most explosive

Jan 1, 1927

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By I Lamb

Past experience of ground settlement and groundwater monitoring for tunnelling projects in Melbourne has provided an appreciation of the value and importance to owners of establishing a broad baseline monitoring program of the ground surface movements and groundwater movements well in advance of the commencement of any excavation and tunnelling activities. For the Northern Sewerage Project (NSP) tunnels in the northern suburbs of Melbourne, a baseline monitoring network of ground settlement points and groundwater wells was established in early 2006, 18 months prior to the commencement of project construction, and has continued throughout the tunnelling and project construction activities. This baseline monitoring network provides insights into the superposition and interpretation of both tunnelling and non-tunnelling effects, such as seasonal effects, which result in ground settlement.In the case of the NSP the baseline monitoring and construction phase excavations coincided with several years of drought. The reduced rainfall developed overall downward settlement trends project wide that could easily be mistaken at the local site level to be construction effects if the baseline monitoring was not available to show otherwise. There are lessons to be learned from the NSP experience for tunnel projects where there are variable surface soil types and where project-specific settlement criteria are to be established for the protection of property prior to construction.This paper presents examples of the baseline monitoring, how the tunnelling-specific settlement was identified and determined, and what this means in terms of how settlement criteria should be established and set for project consenting and in the construction contract documents.

Mar 8, 2011

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

Discussion of the paper of ROSWELL H. JOHNSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 221 to 226. A. C. LANE, Tufts College, Mass.-About a year ago Mr. Washburne read a paper on the same characteristic oil-sand waters, discussing their chemical character, and the possibility of their chemical character being modified by adsorption in passing through the shale. We are used to consider circulation as being in one stratum, and I have often gone so far as to think that 2,000 or 3,000 ft. clown I could recognize the chemical character as in part connate to a given water. For instance, the St. Peter sandstone, far underneath oil sands, seems to retain' a relatively fresh and peculiar character. I am, therefore, tempted to ask the writer if in his experiments lie has made any test to see whether the chemical character of these waters is also changed, where there is any adsorption, so that the water passing through these fine-grained beds should leave behind its salt as well as its oil. In many cases salt-waters are associated with oil and-gas. A second question has occurred to me. In these days when we hear a good deal about oil flotation, may it not be well to repeat these experi-ments with pyritic concentrates, and see if they observe precisely the same with regard to the selective accumulation of oil and gas. ROSWELL H. JOHNSON.-I thank Profesor Lane for bringing this question forward. I recognize its importance, but. am not able to say I have any data upon that point. It is also very interesting in connection with Dr. Day's hypothesis of fractional filtration, and we may very easily get something happening to the water corresponding in some degree to what we get with oil. D. B. REGER, Morgantown, W. Va.-Mr. Johnson in his paper states his belief that the oil is formed originally from organic matter in the shale, and is forced out of the shale into the porous reservoir of the sand above the shale. He states further, that as you go deeper iii the measures where there is an increasing overburdens, the oil becomes less and the gas increases in large proportion, or lie says that the oil is forced back out of the sand by pressure, into the shale.

Jan 5, 1915

By F. L. Bosqui

Discussion of the paper of F.* L. Bosqui, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 997 to 1033. SIDNEY J. JENNINGS, New York, N. Y.-I notice Mr. Bosqui says that zinc dust can be used profitably. I had occasion recently to try to ship some zinc deist to South Africa, owing to the. high price of zinc in the last six or eight months and the difficulty in getting zinc sheets We were informed that the steamship companies in England refused to accept zinc dust for shipment through the tropics on the score that it was an explosive mixture. C. W. MERRILL, San Francisco, Cal.-In the early days zinc dust was packed in wooden casks. The steamers at that time were very chary of transporting it. It was put on the deck in the wooden casks, and if the zinc dust got wet it exploded. Since that time we have used hermetically sealed cases, in which case there is no risk whatever in its transportation.. This rule of the steamship companies is perhaps another sample of their ultra-conservativeness. HENNEN JENNINGS, Washington, D. C.-Unfortunately, I have not yet read Mr. Bosqui's paper, but believing it might interest you to know something of the beginning of the cyanide process on the Rand, I will speak briefly as to my own knowledge and experience of the early initiation of this process in South Africa. I took the position of consulting engineer of H., Eckstein, the parent firm of H. Eckstein & Co., and a branch of the firm of Wernher, Belt ,C Co., at Johannesburg, in December, 1889, and at that time the Robinson Co. managed by them was the premier company of the fields. Up to this date plate amalgamation and catchment of a small percentage of concentrates by blankets, and in a few instances Frue vanners, were the main gold-saving devices used and had obtained an extraction' of only about 65 per cent of the gold contents of the ore. Also at that time the orebodies were seen to be changing from oxidized deposits to pyritic at varying depths from 50 ft. to 300 ft. below the surface, and uneasiness was felt as to future recovery. The deepest exploitation at any of the mines was not much below 300 ft.

Jan 12, 1915

By H. E. McKinstry

Movement on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence: coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. Introduction It has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941