Search Documents

The Vera Nancy orebodies, although simple in overall geometry, are in detail generally narrow, multi-veined and fluctuating in width, strike and dip. Tight geological control is required to optimise gold and silver production from this bench stoping operation. The processes used to model the resource and to control ore drive development have evolved since mining commenced in 1997. Grade control is a combination of orebody sampling, geological data collection, understanding orebody geometry and the optimisation of ore driving and stoping activities. Global resource modelling utilises mainly drill hole data which is largely superceded by drive development data as stope development progresses. The orebody has a relatively low nugget effect that assists in grade estimation. Rather than rely on sophisticated grade interpolation methods, resource estimation to-date has focussed on developing the geological understanding of the orebody to ensure the framework for estimation is correct. Drill data alone is not adequate to define deposit geometry for stoping . Drive data is used as the dominant data set for stope geology modelling once development for a stope is complete.

Jan 1, 2000

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By E. Topuz, M. J. McPherson, I. M. Konduri

The research is carried out to investigate the flow mechanics and effectiveness of face ventilation using induction fans, as an effort to provide a more efficient alternative to conventional auxiliary duct or brattice ventilation systems. The induction effects and plume longevity of fluid jets are being studied with the help of a plexi-glass model, using water as the fluid medium and creating a system that is dynamically similar to the flow in mine headings. This scaled model represents a typical 1.5m x 6m x 25m heading connecting to a crosscut. Reynolds Number criteria are used to obtain dynamic similarity of the flow in the designed model to simulate real mining conditions. The role of various parameters such as nozzle position in three dimensions, airway roughness, nozzle geometry, and flow rate in the jet are studied. During the laboratory tests, flow visualization techniques, coupled with still and video photography, were employed to identify the flow patterns. The results indicate that in typical coal mine headings, jet fans can produce effective face ventilation for distance up to 30 meters.

Jan 1, 1995

By D. Kwak, S. Han, J. Kim, Y. Lee

"INTRODUCTION In carbonate rocks, it is difficult to characterize due to the high degree of heterogeneity in pore geometry. Carbonate rocks have various types of pore systems such as fractures and vugs, and this heterogeneity should be considered for more realistic prediction of oil production in carbonate reservoirs. This study carried out water flooding experiments using five carbonate rock samples in order to observe the change of physical properties. Firstly, qualitative and quantitative analyses were conducted for each carbonate samples by use of XRD and XRF to evaluate the mineral content. All samples are mainly composed of CaCO3 and after that, the ICP experiments were carried out for the water passing through the carbonate. As a result, it was possible to measure the quantity of CaCO3, MgO, Fe2O3 component in water and due to this effect, the permeability of carbonate was altered especially in the front part of the core. Finally, after the carbonate was saturated by 30 API crude oil, water injection to enhance the oil recovery was repeated and it was confirmed that the oil-producing characteristics are different depending on the dissolution characteristics of carbonate rock samples. CORE SAMPLE ANALYSIS Porosity and Permeability Experiment Porosity and permeability were measured. The procedures are as follows (Figure 1). 1. Measure the diameter and length of the dry core using Vernier caliper. 2. Put the core in the core holder, run vacuum pump until the inlet and outlet pressure gauge equal. 3. Saturate the core using ISCO pump to inject water at 650 psi 4. Measure the amount of water and calculate the porosity 5. Set up the outlet pressure at 500 psi. 6. The flow rate measure when the equilibrium 7. Calculate the permeability through Darcy’s Law. 8. Cutting of core upstream and downstream about 13cm, and measure the each of permeability."

Jan 1, 2016

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"Performance testing of prepartion plants is referred to as plant audit. It evaluates plant performance under normal operating conditions and is aimed at improving yield through knowledge of actual process performance and interactions between different processes in a plant.This paper describes the program to evaluate the performance of several Canadian preparation plants. The performance test requires the planning of a sampling campaign that would include all circuits in the plant. Samples are analyzed to determine washing characteristics (screen and float-sink), ash and per cent solids of feed and products of separation units in the plant. Performance characteristics are established based on analysis and material balance. Specific recommendations can then be made to improve recovery, and identify and explain potential causes of apparent deficiencies.The objectives of the program are to reduce the cost of production by improving recovery of clean coal and, in tum, to reduce disposed tailings, establish baseline information on coal preparation plants performance in Canada, and define R&D work needed to optimize plant operation."

Jan 1, 1993

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By Haldun Kurama, Cenk Karakurt, Ilker Bekir Topçu

"The usage of binders or pozzolanic materials in the production of concrete is not new. However, in recent years, the use of the pozzolanic siliceous material such as natural zeolite and coal combustion ash (CBA) has received re-attention due to the generated considerable interest in the economical use of both naturally occurring raw materials, recycling of the waste material and saved energy. In this study, the potential and utilization opportunities of natural zeolites and bottom ash (BA) in concrete applications were reviewed. Case studies, conducted to determine the possible usage of the natural zeolite and BA in concrete production, i.e. light weight concrete (LWC) were also presented. The physical and mechanical properties of cured concretes were examined to find out the competitive material usage on the final product properties. Autoclaved aerated concrete (AAC) with 1.1 nm tobermorite (5CaO 6SiO2 5H2O) as binder is a lightweight construction material that mainly uses in place of concrete to manufacture various building materials, including blocks, panels, slabs and the like. The material is a mixture of sand, lime, cement, gypsum, water and an expanding agent, which causes the raw material to rise like bread dough, with countless small air pores. AAC can be molded and cut into precisely dimensioned units and cured in an autoclave, which steam cures the concrete under pressure. During this process, the ingredients combine to form the calcium silicate hydrate gels that establish the special properties of the finished product. The process produces a material that is only one-fourth to one-third the weight of a conventional concrete block (bulk density of 400-800 kg /m3) of the same size. Regular AAC offers considerable advantages over other construction materials such as high thermal and sound insulation, excellent fire resistance, high resource and energy efficiency, low environmental impact, and finally outstanding structural performance (especially for earthquake zones) [1]. Its lightweight also makes it easy to use during construction, and its aerated structure gives it better thermal insulation and sound absorption properties than conventional concrete."

Jan 1, 2008

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

By Denise Y. Dizon

The objectives of this study were to document the hydrologic impacts of longwall mining on streams, identify the factors affecting the extent of stream dewatering, and develop empirical trends to predict the extent of dewatering and recovery of streams in advance of mining. This study on stream impacts is a companion to a stud; conducted on ground water impacts from longwall mining, which was done as part of the same research project at the' same locations and times. The study areas are three mine sites in north- central West Virginia. Mine A, located in Upshur County, has relatively thin mine overburden under the valley streams (105-115 feet). Stream monitoring there continued the earlier work of Cifelli and Rauch (1). Stream dewatering was severe with streams often going dry over the longwall panels during baseflow conditions. The lost water was probably flowing to the mine. Dewatering began in streams over the mine entry areas adjacent to the panels and as much as 380 feet from the nearest panel edge. The angles of dewatering influence ranged 22 to 72 degrees with respect to the nearest mined panel edge. Discharge then typically increased as the streams- flowed across the panel edge, but then decreased again over the panels. These streams were often ponded by local reversals in hydraulic gradient caused by land subsidence, and often dried up after flowing a few hundred feet across the panels. This occurred over panels that were previously mined up to eight months before. Mine B, located in Monongalia County, has relatively thick mine overburden (475-485 - feet) under the major stream. Stream dewatering was severe there during warm season baseflows, with complete dewatering occurring then over the longwall panels. This dewatering occurred over mined panels up to five years old, probably in response to a major anticlinal axis lineament and fracture zone in the stream valley. Mine C. located on the West Virginia -Pennsylvania border, has relatively thick mine overburden (about 585-630 feet) under the monitored streams there. stream dewatering was only partial, and these streams typically recovered their lost discharge downstream of the mine, indicating that lost water was not recharging to the mine. Only longwall panels less than one year old were associated with stream dewatering.

Jan 1, 1990

By Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

At the present time of depletion of reserves of high grade rare earth deposits, it has become necessary to involve low grade raw materials in the production. Among the rare-earth deposits in Kazakhstan, the most advanced one is Kundybai. The mineralogical composition of ore is represented by the minerals: a-quartz SiO2, kaolinite Al2(Si2O5)(OH)4, muscovite KAl2(AlSi3)O10(OH, F)2, albite Na(AlSi3O8), rutile TiO2, and hematite Fe2O3. It contains: 59.1–68.5% SiO2, 19.1–28.4% Al2O3, 7.2–10.3% Fe2O3, 0.51–0.84% TiO2, 0.10–2.32% CaO, 0.39–2.10% MgO, and some other elements. Rare earths are located in the clay part (kaolinite, goethite) in the ion-adsorbing form, and they are represented by the main ore mineral churchite - YPO4·2H2O. In the ore the amount of rare-earth elements (total REEs) varies from 210 to 600 ppm. Elements of the cerium group predominate (La, Nd, Ce, Sm, Pr) and the yttrium group is represented by Y, Gd and Dy. Extremely thin intergrowth and accumulation of REEs in clay minerals cause difficulties in their recovery using flotation and gravitation beneficiating methods. The purpose of this work is the development of an extraction method for the main mineral components of ore with transfer of the total REEs into the solution with high extractive efficiency. Results of the experimental work into high-temperature processing (hereinafter referred to as sulphatization) of ore by sulphuric acid with subsequent dual-mode water leaching of the sulphate product (sinter) are presented in this manuscript. The influence on the ore sulphatization process of some physical and chemical parameters: liquid-to-solid (L/S) ratio (0.36–0.86 cm3/g), temperature (100 – 500°?), concentration of sulphuric acid (3.0–18.62 mol/L) and duration (0.5–2.5 h) was studied. Optimal technological parameters of the process were determined to be: L/S ratio 0.36–0.46 cm3/g; temperature 500°?; concentration of H2SO4 9.0 mol/L; soaking time 1.5 h. Under these conditions it is possible to obtain extractions of ~ 85% REE, as well as 58% aluminium and 10% iron. XRD and IR-spectroscopy analyses were used to determine the material constitution of sulphated cakes obtained under optimal conditions. It was found that the primary minerals are quartz and muscovite; however different sodium aluminium silicates and albite minerals are present as well. In the future, it is proposed that the leach residue cakes are processed into precipitated silica (“white soot”).

Jan 1, 2016

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By M. D. Banghart

The Republic of South Africa is an outstanding example of the benefits to a new land by the application of individual enterprise, capital and know-how. While South Africa was colonized by European and Bantu people some 300 years ago, it was only 70 to 80 years agog when diamonds were discovered at Kimberley and gold on the Witswatersrand, that the mining, industrial and commercial potential of the country began to emerge. South Africa s national income rose from R1, 200 million in 1945 to over R4 billion in 1960 (1R = 10 shillings = $1.40 U. S.) The annual national income per head of population -- including all races -- is currently R254 (£127) This compares with £24 for India., £30 for Nigeria, and £50 for Ghana. Allowing for the increase in population, the increase in real income per head of population was about 40% during the past 15 years.

Jan 1, 1962

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By William Gleason

"It has been more than 10 years since Montana Resources’ copper/molybdenum mine has had a lost-time injury at its site in Butte, MT. With more than 350 employees and an average production of about 15.5 Mt/a (17 million stpy), which includes 29.5 kt (65 million lbs) of copper and 4 kt (9 million lbs) of molybdenum, the mine’s journey to a decade of exemplary safety is an impressive feat that has required hard work, commitment and, most of all, leadership from every level of the operation.It has not always been an easy journey, nor has it been one without scrapes and bumps along the way, but it is one that has produced stellar results. Mike McGivern, vice president of human resources, and Pete Steilman, safety manager at the mine, spoke with Mining Engineering about how the operation transformed from a site that was accustomed to collecting citations for safety violations to one that is now collecting awards for its safety record.Simply put, Montana Resources has made safety a value and the people its top priority.The operations faced many predictable challenges in 2003, when the mine was being brought back online after three years of sitting in care-and-maintenance status. It had been shuttered in 2000 because of low commodity prices and high operating costs, and, in the three years that the mine was idled, the equipment became dilapidated, and some of it was no longer in compliance. Less than half of the workforce returned to the site for the restart, and the team was challenged with getting the gears turning again to produce copper and molybdenum. But the most daunting challenge of all of was keeping the workforce safe during the transition.In the first few years of operation the mine racked up citations from the U.S. Mine Safety and Health Administration (MSHA) at an alarming pace, so much so that in May 2006, Montana Resources received a letter from the MSHA District Office informing the company that the operation was being placed on the Potential Pattern of Violations list due to its excessive citation history and high rate of significant and substantial citations. It was clear that something significant had to be done to change the course of action at the mine."

Oct 1, 2019

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By O. Nomland

The work of The Bahrein Petroleum Company, Ltd., on Bahrein Island consisted mainly in continuing development work and prospecting previously reported. The exploratory work, however, has been greatly minimized and new wells are being drilled, chiefly for the development of larger production; 20 wells had been completed by the end of 1935 and 8 were being drilled. In addition to what has been referred to as the ''main pay," two deeper productive horizons have been discovered, which apparently will greatly increase the potential of the field although the areal extent of this lower production has not yet been determined. The proven acreage of the "main pay" is more than 12,500 acres. Current production (principally from the upper horizons) is about 13,400 bbl. a day. The construction of a 10,000-bb1.-a-day refinery has begun and is to be in operation by July, 1936. It is expected that the capacity will be considerably increased at a later date. The construction of office buildings and a permanent camp has been almost completed. In Saudi Arabia the California Arabian Standard Oil Co., a wholly owned subsidiary of the Standard Oil Company of California, spudded in a well in April, 1935, near the village of Dammam, on the Persian Gulf coast of A1 Hasa. Although several important showings of high-gravity oil and considerable gas have been found, the well is not yet considcred a commercial producer. Dammam well No. 2 has been started farther south on the same structure. A great deal of reconnaissance and some detailed geological work has been completed during the last three field seasons. In order to overcome difficulties of transportation over the desert sand, unusual methods have been used. The parlies penctrating the interior by the use of automobiles and trucks have been supplied with gasoline and provisions by caravans of camels. Mail and supp1ies of lighter weight urgently needed have been carried to the field men by an airplane operated by the geological division of the company. Each party has been supplied with a radio receiving and transmitting set to keep in contact with the airplane as well as with geological headquarters at Jubail on the coast of A1 Hasa.

Jan 1, 1936

By William H. Baer, George M. Carlton, Blake M. Loring

IT is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen.1,2,3 Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). EXPERIMENTAL PROCEDURE The material for this investigation consisted of extruded rods 1 ¼ to 1 ½ in. in diam. The chemical compositions were as follows: [ ] The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0-015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to ±3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements.

Jan 1, 1948