Search Documents

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By Levent Ozdemir

A 6-ft. diameter laboratory tunnel, raise and shaft boring machine was designed and constructed to carry out research investigations to enhance the performance of mechanical rock excavation equipment. The machine is operated with a computer control system and features extensive instrumentation to monitor and record various test parameters, including tri-axial cutter forces, machine thrust, torque, rpm and penetration rate. An extensive laboratory testing Program has been conducted using this machine, demonstrating the feasibility of attaining high rates of penetration in various sedimentary geologies. Also, a large data base has been developed to serve as a basis for the improved design and performance of tunnel, raise and shaft boring equipment.

Jan 1, 1986

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By Leonard Obert

[Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillars, arches, and other structures. Tin r Loa required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E V2d .....(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.]

Jan 1, 1940

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By D. Harrington, M. W. Von Bernewitz

"The erection of barricades by men who are shut off from escape in mines at time of fire or after an explosion has been consistently advocated by the United States Bureau of Mines. Largely through the publicity given by the bureau to this excellent type of emergency safety endeavor, several hundred lives have been saved during the past 20 years. One of the earliest instances of barricading in the United States of which there is fairly complete record was in connection with the Cherry mine fire in Illinois in 1909; in this fire 259 lives were lost, but 20 men were saved by two barricades and were brought safely to the surface after seven days. In another coal-mine fire, followed later. on by an explosion, at Delagua, Colo., in 1910, 79 lives were lost, but 18 men saved themselves by erecting canvas brattices or barricades; the miners in one barricade were removed safely after five hours and those in another after 21 hours. In 1911, after an explosion in a coal mine at Briceville, Tenn., in which 84 lives were lost, five persons were brought out alive after 58 hours behind a barricade. Twenty hours after an explosion in which 73 were killed at McCurtain, Okla., in 1912, 13 men were taken out alive and one dead from behind a barricade or partition constructed of canvas. In 1914, after an explosion at Eccles, W. Va., in which 181 were killed, 35 men barricaded themselves in one place and after four hours were brought to the surface alive; this barricade was also of canvas. In 1915, 112 men were killed in an explosion at Layland, W. Va., but two groups of men, 47 in all, were able to barricade themselves; after four days 46 men were rescued alive, but one man was dead. In 1915, an explosion at Boomer, W. Va., killed 23, but 27 others barricaded themselves in one place and after seven hours came out alive. All of the foregoing instances of barricading were in coal mines. In 1917 there were three cases of barricading in a Montana metal-mine fire (the North Butte) during which 163 lives were lost. One of the barricades, sheltering 19 men, failed because the region barricaded was in porous broken ground through which the poisonous gases seeped and killed the entire group. From another of the barricades, engineered by an assistant foreman, 8 men were taken out, 6 uncon¬scious and 2 dead, 50 hours after the fire started. The 6 unconscious men lived, out the assistant foreman who directed the men was one of the 2 who had died. In the third case of barricading in this metal-mine fire,,men, also led by an assistant foreman, kept themselves closed in for about b6 hours and then broke barricade or bulkhead, 25 oing in one direction to safety, and 4, including the assistant foreman, going in another direction to death from poisonous gases. There have been a number of other cases of barricading, some successful and others a failure. Probably the worst failure was that in the argonaut (gold) mine fire in California in 1922; all of a group of 46 miners behind a barricade were found dead when reached after 21 days."

Apr 1, 1933

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By R. V. Smith, E. J. Dewees, R. H. Williams

Before this paper was presented, the terms "f" and "v1/f in flow equations had been called "friction coefficient" and "friction factor," respectively. However, many authors have used the names for the terms interchangeably, with the result that considerable confusion has existed in the literature on flow of fluids. In an effort to establish a clear and concise terminology for these terms, the authors have designated f as "resistance coefficient" and dm as "transmission factor." Transmission factors for the flow strings of gas wells were determined by tests on wells in six fields of Oklahoma, Texas, and Louisiana. Data were collected on 14 gas wells while gas was flowing through 1 1/4, 2, 21/2, and 3-in. tubing and 51/2 and 7-in. casing. The transmission factors developed from these data were found to follow the resistance equation published by Nikuradse1 for turbulent flow in "rough" pipes with an average absolute roughness of 0.000,65 in. This average absolute roughness is believed to be representative generally of the flow strings of gas wells with the exception of those that have been exposed to corrosion or other conditions causing undue roughness. Also, use of an absolute roughness of 0.000,65 in. probably will result in transmission factors that are more representative of gas-well conditions than those in common use today, provided that the transmission factors are calculated by the methods outlined in this report. The authors believe that use of these transmission factors will permit calculation of more accurate subsurface pressures in gas wells than those in use today. Engineers use transmission factors in flow equations to compute subsurface pressures in flowing gas wells from measured wellhead pressures. These subsurface pressures are necessary for determining the productivity of gas wells from "back-pressure" tests. The methods of calculating pressures in flowing gas wells, as outlined by Rawlins and Schellhardt2 in Bureau of Mines Monograph 7, are based on the transmission factors in the well-known Weymouth formula" Natural gas engineers have realized that errors introduced by using transmission factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; but they also know that such factors are important considerations in testing large-capacity wells. Accordingly, the research described in this report was undertaken to fulfill the need for more accurate means of calculating subsurface pressures in gas wells. This report is part of the Bureau's study of the flow of natural gas through pipe and commercial pipelines. Several of the conclusions regarding flow in the flow strings of gas wells were influenced by the results of the study of flow in horizontal pipelines. These instances are mentioned in the text of this report. METHODS OF COMPUTING TRANSMISSION FACTORS Methods and procedures for computing transmission factors for turbulent flow in circular pipes from test data taken on gas wells have been derived and explained in detail in a paper by Smith4. As these methods were used to calculate the transmission factors presented in this report, a summary is included. Starting with

Jan 1, 1955

By E. W. COCHRANE, R. HOPKINS, G

The number of completed petroleum refineries in the United States continued to decline in 1938, but the total capacity to process crude oil increased materially. This information was obtained in connection with the Bureau's annual canvass of refinery capacity as of January 1, 1939. In spite of the addition of a half dozen plants in Illinois and the inclusion in this year's list of several more "pot-stills" in Montana, the total number of plants, and inactive, declined from 551 on January 1, 1938, to 538 on January 1, 1939. was entirely in shut-down plants, as the number of operating plants rose from both active The decline 431 to 435. Yost of the plants dismantled were situated in Wyoming and Texas, parts or several from the latter being transported to Illinois. About 10 more East Texas refineries were dismantled in 1938, leaving about 15 plants in the field, only 8 of which were operating on January 1, 1939. Although the total completed capacity increased from 4,351,151 barrels on January l, 1938, to 4,508,555 barrels on January l, 1939, the operating capacity declined, and the inactive capacity increased about 50 percent, or from 380,955 to 574,770 barrels. These shifts in capacities reflect the comparative slump in the refining industry in 1938 after the prosperous year 1937. Daily average crude runs in 1938 were 3,192,000 barrels, from which it may be figured that the operating ratio for the active units was about 81 percent of crude and for all completed equipment 74 percent. The highest daily throughput in 1938 was about 3,400,000 barrels, at which time the reserve capacity represented in the active equipment was at least 500,000 barrels, in addition to about that much capacity shutdown. In an emergency, much more reliance could be placed on the reserve capacity of the active equipment, as much of the shut-down capacity is obsolete at present specifications and prices. Regarding obsolescence, the refiners reported 418,165 barrels of their idle capacity in good condition on January l, 1939 and 156,605 barrels in poor condition. However, it is probable that the former reflects an optimistic viewpoint. Refinery activity, as represented by new construction and dismantling, declined materially in 1938. The new capacity added in 1938 was 378,350 barrels compared with 394,680 barrels in 1937. Probably 1939 will see a much larger decline, as the new capacity under construction on January 1, 1939, totaled only 142,250 barrels compared with 283,020 barrels the preceding year. The capacity represented by the new plants was negligible throughout

Oct 1, 1939

By S. H. Ash

In the early nineties it was observed by several European investigators and by C. S. Rice4 that an explosion could be checked and would not propagate in the parts of a mine where shale or other inert dust was present in large amounts.5 After the disastrous Courrieres explosion in France that killed 1,100 men, coal-dust explosion tests were made in France in 1907 and in Great Britain in 1908 which resulted in the conclusion that if enough incombustible dust were properly spread throughout passageways charged with coal-dust, the propagation of an explosion by the coal-dust could be prevented. In 1908 the Federal government authorized the investigation of the causes of mine explosions and of possible methods of preventing them, with the result that during 1911 the United States Bureau of Mines, after making several tests, suggested that rock-dust be used in gassy or dusty bituminous coal mines. Since that time, experiments and investigations6 have proved conclusively that widespread explosions can be prevented in coal mines by efficient rook-dusting.

Jan 1, 1930

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

In an earlier study at this laboratory,' the authors investigated the solid solubility of holmium in copper, silver, and gold, and also the melting point of the first eutectic on the noble-metal-rich side in these systems. In a more recent study of the solubility of rare-earth metals in gold at this laboratory. Rider, Gschneidner, and McMasters2 noted that the reported eutectic temperature in the Ho-Au system was lower than the corresponding eutectics in systems of dysprosium and erbium with gold. A redetermination of the eutectic temperature in the Ho-Au system with the same alloy used in the original study showed the eutectic temperature to be 810°C instead of 778°C as originally reported. (The eutectic temperatures in the Ho-Ag and Ho-Cu systems were also redetermined and were found to be 795" and 864°C compared to 787° and 868°C, respectively, which were reported originally.) Since this large change in eutectic temperature made the solubility data appear questionable, new alloys were prepared, heat-treated, and examined metallographically. The procedure of sample preparation and heat treatment used in the original work' was followed except longer heat treatments were used ranging from 7 days at 600°C to 6 hr at 900°C. The results obtained are shown in Fig. 1. There is good agreement between the two studies in the maximum solubility of holmium in gold. Since the slope of the solvus is less pronounced in the present study, the extrapolation to 550°C shows a solubility of 1.6 wt pct Ho in gold compared with 1.0 wt pct in the original work. Since additional data were obtained and longer heat treatments were used in the present study, the larger value is believed to be more accurate. The authors wish to express their appreciation to P. Rider and K. A. Gschneidner. Jr., for bringing this discrepancy to their attention, and also to D. Thompson for assisting in the present study.

Jan 1, 1965