Search Documents

By Erwin Pink

It has been pointed out in a previous publication' that, for a given strain rate, serrated yielding can be observed only at certain test temperatures. Fig. 1 shows the results obtained for polycrystalline and re-crystallized tantalum, Va group in the periodic table of elements, where serrations in the course of deformation match the decrease of total elongation. However, there was no evidence of repeated yielding when testing molybdenum or tungsten, VIa group, at similar conditions, i.e., annealed and air-cooled samples (serrations have been found in quenched tungsten2). The reason for the observed serrations in the stress-strain curve are dissolved impurities on interstitial sites of the lattice. Of importance is the concentration of oxygen, carbon, and nitrogen, which are in random solution. Two methods to calculate the limiting concentrations for serrated yielding have been evaluated and applied with more or less success in estimating the role of carbon and nitrogen in mild steel.3 J. Friedel4 has given two equations, which determine the upper and lower strain rates i for the appearance of serrations at a certain test temperature: W denotes the binding energy of the interstitial atom, -1 ev for refractory metals;5 e' the portion of continuous strain in the discontinuous stress-strain curve, measured as -3x10-3; b the Burgers vector, c the concentration, see Table 11, in atom fractions; p the dislocation density, -2 X l09 per cm2 at an average stress ?, -15 kp per mm2 at medium strain. k stands for the Boltzmann constant, T for the absolute temperature, and D for the diffusion coefficient. Table I. Eq. [1], for a given strain rate, determines the minimum temperature, and [2] the maximum temperature, below or above which no "dynamic strain-aging" can occur. According to the calculation, which uses the given quantities, serrations should only be observed within the cross-hatched temperature regions in Fig. 1, and this is in good agreement with the experiment. The effect of varying impurity concentrations is indicated schematically in Fig. 2: only Eq. [I] is affected. Setting Eq. [I] equal to [2], one can calculate the limiting concentration cmin which first causes serrations. The second method uses the aging condition by Cottrell and Bilby6,7 \£i/ \ n. a / where n(t) is the number of impurity atoms, which segregate at a dislocation line of 1 cm length after the time t (t in our case is the time between "repeated yield drops" in the serrated curve, or, the time until the above mentioned strain E' is obtained, i.e., -1 sec for medium intensity or serrations). no is the number of impurity atoms in 1 cm3 and A = Qb4ep[(1 + v)/(l - v)], derived from equations given in Ref. 7. p is the shear modulus, 18,800 kp per mm2 for tantalum, 12,200 for molybdenum, AE the tetragonal distortion caused by interstitial impurities in a bcc lattice (approximately 0.4 for both tantalum and molybdenum) and v Poisson's ratio (0.35 for tantalum, 0.30 for molybdenum). From Eq. [3], combined with the condition for a pronounced yield drop as formulated by cottrel16 (at least one impurity atom segregated at the unit length of a dislocation), again a no min, and hence the concentration Cmin can be calculated.

Jan 1, 1970

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

By P. Shahinian, R. L. Stegman, M. R. Achter

Creep strength has been determined as a function of oxygen pressure for nickel at 510" and 600°C. Creep-rupture life drops from its highest value at the ultimate vacuum of 10-7 torr to a high pressure plateau of nearly constant life which, at 600°C, commences at torr. This behavior is described in terms of a model that relates surface gas adsorption and the generation of fresh crack surfaces. In a calculation based a this model the predicted pressure beyond which the creep strength should not decrease further has been found to agree well with the observed value. The introduction of oxygen during creep in vacuum was found to cause a prompt rise of the creep rate. The magnitude of the environmental effect was much less than generally observed in fatigue and this is attributed to the diffarent crack morphologies in creep and fatigue. GASEOUS environments are known to affect creep resistance adversely1-5 but the effects have received less attention than the much larger ones in fatigue. At low temperatures it has been shown for nickel that the creep rates are faster and the rupture lives are shorter in air than in vacuum and that these environmental effects can be correlated with faster crack growth rates in the reactive environment.' In support of a mechanism of gas adsorption at the crack tip to explain the above effects, a calculation based on kinetic gas theory showed that surface coverage by gas was not as rapid as the exposure of fresh metal at the crack tip in the ultimate vacuum but was in air.7 In fatigue a number of investigations have demonstrated that the reduction of life with gas pressure usually follows a step curve with most of the reduction occurring in a transition range at intermediate pressures and little or no change at high and low pressure.8 There have been no studies, however, in which creep strength has been determined as a function of reactive gas pressure to see whether similar effects would be found. This investigation was undertaken to study the kinetics of the environmental effect in the creep of nickel. EXPERIMENTAL PROCEDURES The environmental creep apparatus was constructed to minimize many of the experimental conditions which can cause scatter in data. Dead weight loading is employed and weights are contained within the environmental chamber to eliminate bellows and the necessity for compensation for gas pressure changes. Elongation over the specimen gage length is recorded from a Riehle Model DV Controlled Environment Extensometer which provides readout to 2.5 x 10- in. Temperature is monitored and controlled from a thermocouple at- tached to the specimen gage length to +0.5oC or better. The freon trapped oil diffusion pump vacuum system included an auxiliary liquid nitrogen trap and, with a wide range variable conductance leak valve, pressures from the ultimate vacuum of 10"7 to l03 torr of any desired gas are obtainable. Pressure is measured by means of a hot filament ionization gage below 10"3 torr and a NRC Model 530 Alphatron Vacuum Gauge above 10-3 torr. The oxygen, which was leaked into the environmental chamber, was an Aviator's Grade of 99.5 pct purity with a dew point of -80°F. Analysis of the nominal 99.8 pct Ni showed the following percentages of major impurities: 0.02 C, 4.01 Mn, 0.005 Si, 0.01 Cu, 0.02 Fe, and 0.034 Mg. Cylindrical specimens were machined with a 0.180

Jan 1, 1970

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By A. K. Sheik

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By E. V. Manlapig, David J. Spottiswood

In recent years great advances in the automatic control of flotation plants have been made, mainly due to the development of reliable sensing instruments to monitor process performance and the development of an adequate understanding of system responses to process disturbances. Some of the control strategies used in flotation plants which apply computer control are presented here. These schemes, which involve the control of collector; depressant, frother, and air and pulp level, are analyzed with respect to their control objectives, control variables, and the instrumentation involved. The knowledge gained in understanding these strategies may be applied in the dew and implementation of control system in other concentrators.

Jan 1, 1981

By F. Weinberg

WHEN impure Zn (< 99.99 pct)&apos;&apos;Z or Zn-Cd alloys3 are progressively solidified, a cell or "corrugation" substructure4 is produced in the solid, with a high impurity or solute concentration along the cell walls. When these materials are polished and suitably etched, etch pits are often observed along the cell walls. For the Zn-Cd alloys these etch pits have been associated with decorated dislocations, present in the corrugation boundaries to accommodate the lattice strain. In the course of an investigation of Zn-2 pct Au alloy, molten metal of this alloy was poured into cold water and the resultant solid pieces were sectioned, polished and etched with a Cr0 ethant. An extremely regular cell pattern was observed on the etched surface, similar in general to the corrugation structure previously reported for impure zinc and Zn-Cd alloys. At higher magnification, regularly spaced pits were observed along the cell boundaries. An example of the regular cell pattern at the center of a specimen is shown in the center and lower portions of Fig. 1; the top of the figure shows the pattern near the specimen surface. Typical etch pits in the cell walls are shown in Fig. 2. It was surprising that a cell pattern as regular as that shown in the center of Fig. 1 was produced at the very rapid solidification rates used (estimated as > 1 cm per sec). In addition, the distribution coefficient for the Zn-Au system is greater than 1. Accordingly, the center of the cells should be rich in solute and should etch

Jan 1, 1963

By B. Stas, L. Siska, L. Dlouhy, A. Skrabis

The basic research program of the Scientific Coal Research Institute at Ostrava - Radvanice into the problem of geophysics has been influenced by the specific nature of present urgent geo- physical problems in mines and directed to attain higher grade of effectiveness, safety, and overall economy in mining activity. The research has been divided into two basic trends: Seismoaccoustic research deals with questions pertaining to safety in mining especially when work is in coal seams under "heavy roofs", i-e., thick beds of sandstone prone to rock bumps and characterized by caving. Methods have been developed with the definite aim to determine the time and space prognosis of critical states of tension in the rock mass when stability is disturbed as a result of mining activity. Seismic research is directed towards the determination of detailed structural and tectonic elements of the internal geological formation of the Carboniferous rocks, the establishment of continuity or tectonic faulting of coal seams, and the evaluation of magnitude, shape, and time changes in the rock mass surrounding the mine workings. The measurements have been applied either from the surface or in the underground workings according to the specific nature of individual problems. Satisfactory results have been obtained in some branches of this research, other branches being still in the stage of development. Remarkable results have been achieved in the development of seismoaccoustic methods designed to establish the time prognosis of dangerous dynamic phenomena accompanying the process of strata deterioration above the worked longwall face. One of the most

Jan 1, 1971

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By Tugba Kami?oglu

Hydromagnesite (Mg5(CO3).(OH)2.4H20), one of the sedimentary deposits in Salda Lake Basin, is developed under the control of active tectonics regime. Since the occurrence and deposition mechanism of hydromagnesite are unstable under atmospheric conditions, in order to evaluate the precipitation process, systematic host rock, lake water (surface, 20m, 40m, 60m) and hydromagnesite sampling were carried out. Macro, micro, XRD and chemical investigations were done in detail. Not only the results and formation and crystallization mechanism but also hydromagnesite&apos;s St values were evaluated. Main resources could be ultramaficmafic surrounding rocks for hydromagnesite formations. However, hydromagnesite development is considered in different phases, because it has showed various characteristics in Kayadibi and Köpekcayin areas. In Kayadibi area Huntide-Dolomite-Aragonite-Hydromagnesite paragenesis has been realized. Hydromagnesite has also formed in Köpekcayiri area, large amount of hyrdomagnesite occurrences and levels various are noticeable. Actual position of hydromagresite levels exhibits tectonic influences in and around the lake. Therefore, the levels seems to exhibit secondary formation properties. In addition, the formations are being still maintained sedimentation as products of a peripheral deposition phases. Resolving and redifferentiation sedimentation processes probably improve in periods of lake water chemistry especially Ca/Mg proportional changes, and also SI variations indicate the mentioned precipitation mechanism. Similarly, side and into the lake hydromagnesite is stored different levels and ultramafics-mafics rocks fallow indicated stages. It is postulated that hydromagnesite formation, which is existed by result of determined developments and multiphase sedimentation, could be originated from probable crack zones on the lake bottom.

Jan 1, 2005

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.&apos; The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

By I. F. Avery

The productive capacity of natural-gasoline and cycling plants in the United States on January 1, 1958, was 48.8 million gallons per day, according to the Bureau of Mines biennial survey. This represented an increase of 2.4 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 7.5 million gallons per day. The major increase in operating capacity occurred in Texas and New Mexico. In New Mexico, capacity increased 43 percent. The total number of plants decreased from 600 on January 1, 1956, to 584 on January 1, 1958. The number of operating plants decreased from 571 to 558. Five new plants were completed in Colorado, increasing the number of operating plants from 7 to 12.

Jan 1, 1958

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.&apos;, &apos; They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast&apos; postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,&apos;&apos; a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By S Li, Y Lei, X Wu, C Ma, W Q. Zhang

The failure of roof of thin bedrock working face under loose aquifer in a coalmine can lead to water-sand inrush disaster. Based on the accident of water-sand inrush in 30108 working face of a mine in Shaanxi province, China, the mechanism of water-sand inrush is theoretically analysed. The process and critical conditions of water-sand inrush in working face are reproduced by numerical simulation where the bedrock thickness is 20 m, the clay layer thickness is 40 m and the mining height is 6.5 m. The study found that under the condition of thin bedrock and thick clay layer, the characteristics of the clay layer have a significant inhibitory effect on the development of the fractured zone, and the development of the water-conducting fractured zone is incomplete and insufficient. However, in the process of continuous mining of multiple adjacent working faces, the strength of the clay is gradually reduced by the influence of mining and the erosion of water, and the height of the fractured zone is gradually increased. In the subsequent mining process of the working face, the roof is more likely to be cut-off and lead to water-sand inrush. From the initial failure of the clay to the final crack directly through the surface, the shear strength of the clay is reduced by about 52 per cent. Further simulation found that in addition to the characteristics of the clay layer itself, the main factors affecting the water-sand inrush in the working face caused by overburden failure also include the difference in bedrock thickness and strength, and the difference in coal seam mining height. With the increase of bedrock thickness, the development height of the fractured zone increases gradually with increases of bedrock thickness when the cutting failure of overburden rock no longer occurs. With the increase of mining height, the height of water flowing fractured zone also increases, but the cracking ratio gradually decreases. Therefore, it’s of great practical significance to systematically study the mechanism and critical conditions of water and sand inrush in mines and the main influencing factors for preventing similar accidents in mines with similar conditions.

Nov 29, 2022

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

By D. B. McGilvra

ANY mining operation in the Altiplano of the Andean range presents problems and imposes obligations on the mining company not usually met with in the United States. The Aguilar mine is in a sparsely populated, semiarid region, 50 km by road from the Argentine State railroad station of Tres Cruces, Jujuy, Argentina. In starting an operation in such a location it becomes necessary for the mining company to prepare first for the needs of the required force of workmen and their families. This program calls for houses, schools, hotels, water, electric power, laundries, post offices, police

Jan 1, 1947

By F. M. Van Tuyl

The oil industry had its inception in the United States in 1859 when the first oil well was drilled by Col. Drake at Titusville, Pennsylvania. From, a production of 2000 barrels for that year there was a slow but steady increase, with some fluctuations, up to 1901 for which year the output was approximately 69,389,194 barrels. Since that time the production has increased with leaps and bounds due to the rapid rise of the automotive industry, the widening use of oil as a fuel under boilers and the development of the. Diesel engine. The production for 1921 is estimated to have been 469,639,000 barrels. During the same year more than 125 millions of barrels were imported from Mexico. The oil industry, including the production, transportation, refining and distribution of petroleum and its products, is now the third largest in the country. Present Condition of the Industry During and immediately after the war the demand for petroleum exceeded the domestic production plus the imports from Mexico with the result that our storage oil was heavily drawn upon. Prices for crude exceeded all previous levels in the history of the industry. Pennsylvania crude sold for $6.10 per barrel and Mid-Continent crude for $3.50. Such prices stimulated wildcatting greatly with the result that several important new oil pools were discovered. Then as production increased the depression came which caused a large falling off in consumption. Pennsylvania crude fell to $2.25 per barrel and Mid-Continent to $1.00. Large oil companies such as the Standard, Sinclair and Empire took advantage of the situation, erected additional storage tanks and bought up millions of barrels to hold until better prices returned. Prices have already improved owing to a better market, but the domestic production coupled with the Mexican importations is still in excess of the demand with the result that the surplus is being stored. At the close of the year 1921, the U. S. Geological Survey estimates that there were 183,890,000 barrels of crude in storage in this country, the largest stocks in the history of the industry, yet an amount sufficient to supply the country for only 119 days at the present rate of consumption. Price reductions are again anticipated in some quarters but in view of the probable falling off in the Mexican output in the near, future due to the rapid rate of exhaustion of several of the most important pools and in view of the expected increase in consumption of gasoline and kerosene during the spring and summer months it is more likely that the present price level will be maintained. Present Sources of Domestic Supply Seven major oil fields are recognized by the U. S. Geological Survey in the United States. These are the Appalachian, Lima-Indiana, Illinois, Mid-Continent, Gulf Coast, Rocky Mountain and California. Two of these, Mid-Continent and California, supply about seventy-five per cent of the present total domestic output

Jan 1, 1922