Search Documents

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By B. S. Lement

No appreciable stabilization of the austenite-martensite reaction occurs in a 15 pct Cr-0.7 pct C steel unless some martensite is initially present. Stabilization is induced by interrupting the subcool below M,; however, disappearance of the stabilization effect as manifest by burst formation of martensite may occur on continued holding at the final subzero reaction temperature. The higher the temperature of intermediate cycling after the initial subcool, the more permanent is the stabilization effect at the final reaction temperature. Appreciable conditioning of retained austenite occurs on reheating to about 500°C. These phenomena are explainable on the basis of the reaction-path theory. A RECENT investigation' carried out by the authors has shown that isothermal transformation of austenite to martensite definitely takes place in a 15 pct Cr-0.7 pct C steel and that appreciable amounts of martensite can form in this fashion. Investigations2-" arried out on other steels and iron alloys make it seem probable that isothermal formation of martensite is a phenomenon of fairly general occurrence. The reaction-path theory of Cohen, Machlin, and Paranjpe5,7 explains isothermal transformation on the basis of thermal activation of strain embryos which generate martensite plates with a velocity approaching that of sound. On the other hand, the nucleation and growth theory of Fisher, Hollo-mon, and Turnbull8 egards isothermal transformation as due to growth of athermally formed martensite nuclei. The experimental evidence obtained thus far favors the reaction-path theory in that the martensite reaction seems to be nu-cleation-controlled rather than growth-controlled. Stabilization is another phenomenon of importance with respect to the austenite-martensite reaction. According to the reaction-path theory, stabilization is a result of relaxation of strain embryos. It is postulated that strain embryos are present at the austenitizing temperature in the form of dislocations or lattice imperfections in the austenite which vary in the extent to which the lattice is displaced along the strain reaction path leading to martensite. On quenching from the austenitizing temperature, athermal martensite starts to form as soon as the M. is reached, because the activation energy of the transformation which decreases with decreasing temperature is lowered to below the level of the highest energy strain embryos. Martensite plates are generated during the cooling below M, from embryos possessing energies above the activation energy corresponding to the temperature at which the cooling is stopped. The distribution of lower energy embryos is changed because of the elastic and plastic strains produced in the remaining austenite as a result of the transformation. This effectively increases the number of strain embryos at all levels of energy below the activation energy and tends to stimulate further martensite formation either iso-thermally or on subsequent cooling. However, if the temperature at which the cooling is stopped is high enough for relaxation of strain embryos to occur, some degree of stabilization against further transformation may be induced. Whether stabilization will be observed on subsequent cooling will depend on the extent of decrease of activation energy with temperature. If the activation energy decreases sharply with temperature, it is possible that transformation will appear to continue with decrease in temperature in spite of the loss of embryos by relaxation. However, with a more gradual decrease in activation energy, stabilization will be manifest by no further transformation on cooling over a measurable temperature range until the

Jan 1, 1954

By R. D. Nelson, F. E. Bowman

Evidence has been found for a (010)a?(111)B[102]a /,11[341]/B crystallographic relationship between the monoclinic a and B phases of plutonium during the a?B transformation. The results of an X-ray diffraction study, where [010] fiber textured a samples were used in the absence of suitable single crystals indicate that the (OIO)a planes become (111)B planes upon transformation under near-equilibrium conditions. The transformation strain along the fiber axis, which was the [010] direction, was measured dila-tomekically; the measured 8.5 pct expansion compares favorably with the 8.44 pct expansion in the in-terplanar spacing represented by the (010)a?(111)B relationship. From plots of the atom positions in each of the related planes, a correspondence was deduced between the [102]a, direction and the [341]B direction. Further analysis of the two lattice structures in the light of this relationship revealed a rotation about the [102] direction of 1 deg 43 min and a slight shearing in this same direction of about 30 min. THIS paper discusses the (B crystal structure of plutonium and the orientation relationship existing between the monoclinic a and B phases during the a?ß transformation. The kinetics of the a?ß and (3 — a transformations have received extensive consideration, and because of the crystallographic complexity of these phases, the question of the mechanisms by which these transformations occur is especially intriguing. Nelson and Shyne1 evaluated the existing experimental evidence and concluded, from the indirect evidence available, that both the ß ? a and a ? ß transformations occur by a martensitic process. Their data reveal the anisotropic nature of these transformations which suggests the existence of specific crystallographic relationships between the parent and product phases. In this paper, we are concerned with the confirmation of the existence of such a relationship resulting from the a ? ß transformation and the derivation of the crystallographic details necessary to specify it. EXPERIMENTAL RESULTS X-ray diffraction and dilatometric data were obtained from samples of a plutonium having a [010] fiber texture. These cylindrical specimens, approximately 1 cm in diam, were prepared by transforming the ß phase to a under the influence of a uniaxially applied compressive load.' The [0l0] direction is parallel to the direction of applied stress; it is also perpendicular to the (010) planes. This correspondence between the plane normal and the direction having the same indices is, in the monoclinic a plutonium structure, restricted solely to this (010)[010] combination. Such a specimen was mounted in an evacuated, elevated temperature specimen holder on an X-ray dif-fractometer so that the diffracting surface was perpendicular to the fiber axis. The a diffraction pattern, Fig. 1, taken at about 115ºC, revealed the predominance of the (020) reflection. This monoclinic, P 21/rn space group yields no (0k0) reflections when k is odd. The temperature was raised slowly to 160°C to effect the complete transformation to the phase; then it was lowered to 120°C so that a diffraction pattern of the ß could be obtained near the a = ß equilibrium temperature for direct comparison with the a at the same temperature. The (3 diffraction pattern, Fig. 2, obtained under these conditions showed a (222) reflection relatively much more intense than in the random pattern. The other reflections appearing with sig-

Jan 1, 1970

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By S F. Simmons

At Broadlands-Ohaaki geothermal system, TVZ, mineral distribution patterns in geothermal wells are analogous to those in epithermal veins. Fluid flow through geothermal wells is focused over vertical intervals >500 m with discharge at rates up to 90 l/s. Focused flow at similar rates also occurs in natural systems where hydrothermal eruption vents provide enhanced vertical permeability. These vents are commonly aligned with the tectonic fabric, indicating fault control at depth. We suggest that host rock strength and structural context exert significant control on the hydrological regime conducive to epithermal mineralisation.

Jan 1, 2005

By F. W. Jessen, H. Kazemi

A washing technique has been developed to form a spherical cavity in massive salt. The technique is, basically, a process of controlling the fluid motion in the cavity, the concentration distribution of brine, the rate of dissolution at the walls of the cavity, and the particular settings of the wash pipe, or pipes (inlet and outlet pipe) employed. For a particular arrangement of tubing and casing, fresh water enters from the casing annulus at a position above the bottom of the tubing, and the dissolved material leaves the cavity through the tubing near the bottom of the projected hole. The initial configuration of the cavity is cylindrical, representing the drilled hole situated at the axis of the projected cavity. As washing progresses the original hole is enlarged radially (any direction perpendicular to the axis of the hole). An inert fluid (generally a hydrocarbon, natural gas, or air) which serves as a blanket is injected through the annular space between the original hole and the casing. The controlled downward motion of this blanket maintains the upper edge of the brine region that is expanding on the surface of the projected sphere. A large spherical glass container and a radial model were used to investigate the flow patterns and the concentration distribution of brine occurring during the progress of solution of the salt. Aluminum flakes and dye were injected and flow patterns were observed and recorded on motion picture film. Based on the results of these model studies and other work carried out in this laboratory, the controlled washing technique was formulated. INTRODUCTION Underground cavities leached in salt beds and salt domes have been used extensively for storing hydrocarbons. Little attention has been focused on the shape of the cavities as long as large volumes were obtained and the cavities were structurally stable. The general process involves circulating fresh water and removing brine. Two distinctly different circulating systems can be employed, each of which yields characteristically different shapes. By far the most generally accepted method of washing storage caverns in salt domes is the direct circulation system. Water is introduced through the innermost pipe of a concentric pipe system, and brine is withdrawn through the annulus. In the reverse-circulation method, water enters through the annulus and is discharged through the smallesc tubing string. The size of the operation, and hence the size of tubing and casing used, depends on such factors as cavity volume, length of hole, availability of water, disposal of brine and power requirements. Underground caverns are from 100 to 1,000 ft or more in length, and when completed vary from 40 to 100 ft in diameter, providing storage of 100,000 bbl or more. The volumes of water required per volume of salt removed vary from 6 to 7 for the reverse circulation method to 10 to 11 for the direct circulation method. Up to 80,000 BWPD are often circulated. In the direct circulation method, because water enters near the bottom of the projected cavity, solution of salt is greatest at this point, particularly in view of the fact that when the washing is begun turbulent flow undoubtedly exists in the immediate vicinity of the discharge of the inlet water. As the diameter of the hole increases, flow rates also are increased, so perhaps the condition of fluid turbulence is maintained for some time. During the later stages of leaching, when capacity of equipment may be the limiting factor in maintaining flow rates, there may still exist some turbulence adjacent to the point of influx; however, for the most part laminar flow conditions prevail. There appears, therefore, rather good evidence to indicate that the state of fluid motion is responsible for the typically shaped cavity which results from such washing — namely a cylindrical form, generally somewhat larger at the bottom than at the top. Depending on the number of so-called stages which might be employed, the walls or surfaces of the salt diminish rather uniformly from bottom to

Jan 1, 1965

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By J. W. Paul

"The economic features of coal mining must take into account the drain on the man power. Study over a recent 5-year period reveals an average yearly loss of 2,125 underground men, of whom 1,182 are killed by falls of roof and coal, and according to recent data compiled by the Bureau of Mines it is estimated that 54,000 men sustain lost—time disabling injuries from the same cause.Under normal activity of the mines approximately 50 lives are taken by falls of roof during every 10 days the mines are operated, or 5 persons are killed per day, which, at a compensation charge of $5,000 each, amounts to $25,000 per day. Add to this the similar number killed by causes other than by falls of roof and we have $50,000 as an approximate daily fatality charge for each day the mines operate. On the basis of 200 working days per year, this amounts to the alarming figure of $10,000,000 annually. An investment at 5 per cent to yield this amount would require $200,000,000, which is equivalent to a capital investment of $0.40 per ton of coal, produced annually, on the basis of 500 million tons. These figures apply only to fatalities for which a fixed or stated amount is paid for compensation and do not include the compensation and hospitalization paid for the approximately 103,000 upon whom idleness is enforced by a lost-time disability injury. In one State having an annual production equal to approximately 30 per cent of the total bituminous production of the United States, the most recent data shows that for each fatality there are eight serious injuries causing 60 days or more lost time. The frequency rate of accidents for that State is less than the average for the United States, and so a conservative comparison may be made by using the figures of that State in estimating the total serious injuries, which gives 16,000 as losing 60 days or more. The average number of underground employees in the coal mines of the United States for the past 10 years has been approximately 570,000; the annual underground fatalities amount to approximately 2,000 and non-fatalities to 108,000, or a total of 110,000, which means that one out of every 5.17 employees ,or 19.3 per cent, receives an injury which results in either a fatality or a lost-time disability; this figure in a little over five years will reach a number equivalent to 100 per cent of all underground workmen. Against this is the record of many miners who have worked 25 years or more without a lost—time disability injury, indicating that coal mining is not necessarily productive of injury or death to workers.In the matter of falls of roof, it is found that 85 to 87 per cent of all fatalities occur at the working face, face of a room or entry, or in pillar work. It is at the working face that the greatest roof hazards are encountered, and when about 75 per cent of the underground employees spend approximately 90 per cent of their working hours at the face, it is logical that there is where injury is most likely to occur.Although the roof hazards may vary in different beds of coal, experience has proved that roof hazards can be successfully controlled in all coal mines, essentially regardless of the character of the roof if constant care and attention are given by the management and employees in applying the principle of safety. In almost every mining district some companies maintain an extremely low frequency rate of injury, whereas in the same district with essentially the same roof conditions the opposite is true.A study has recently been made of a number of reports upon fatalities in one district of one of the principal coal—producing States and it showed that 50 lives had been lost at 23 mines as the result of falls of roof or sides. These reports were made by the mine officials, safety engineers, and safety committees and an attempt was made to give both the cause and the person or factor responsible for the fatality. A summary of the items of responsibility is as follows:"

Feb 1, 1932

By J. L. Bray, S. T. Ross

The paper provides electrometallurgical data on the problem of germanium removal from zinc sulphate solutions. Germanium traces have caused much concern to the zinc refiner. Confirmatory evidence of interaction between germanium and cadmium is presented. Statistical analysis of data expands its significance and enhances its value. Further research is outlined. THE literature contains many references to the effects of trace amounts of germanium in the production of electrolytic zinc. One of the authors had experience with this troublesome element as early as 1917 at Trail, B. C. In 1929, Tainton and Clayton' reported that concentrations of as little as one part per million of germanium were sufficient to cause serious losses in current efficiency. Liddell2 reported that trace amounts of germanium cause marked lowering of the hydrogen overvoltage of electrolytic zinc cells, so that commercial production was impaired. Bray3 recorded the history of germanium in relation to electrolytic zinc production, noting that concentrations below 10 ppm have been found to yield low current efficiencies and copious hydrogen evolution. Koehler' stated that germanium "when present to the extent of a small fraction of one part per million per liter, causes serious evolution of hydrogen with a corresponding reduction in current efficiency." Recently, however, S. W. Ross" reported, from Risdon, Tasmania, that "in the course of leaching . .. dissolved traces of germanium... if not removed almost completely ... increase the reversion of cadmium during the filtration of the copper-cadmium precipitate and reduce the current efficiency during subsequent analysis." The copper-cadmium precipitate referred to is the residue from the zinc-dusting purification of zinc sulphate leach solutions. In the face of such conflicting testimony and with the increasing industrial importance of pure germanium and zinc it was decided to investigate the relationship between cadmium and germanium. Furthermore, other work by the authors showed certain discrepancies to exist in the theories of Tainton, et al. In the laboratory, without marked efficiency decreases, the authors have deposited zinc successfully from solutions containing as high as 1 g per liter of germanium. This could be done only when there was no cadmium present. Preliminary investigations of the suspected rela- tionships were carried out by means of emission spectrographic analysis using a beryllium internal standard. Several solutions containing 100 g per liter of zinc, as zinc sulphate, and 1 g per liter of cadmium, as cadmium chloride, were prepared. These concentrations were on the order of those obtained during a commercial low-acid leaching process. Varying concentrations of germanium were added to these solutions so that the range of 0.0000 to 0.5000 g per liter of germanium was covered. A 250 ml sample of each solution was agitated with 2.5 g of zinc dust for 30 min, filtered, and the filtrates were examined spectroscopically. Qualitative evidences of cadmium traces were found in those filtrates which originally contained above 10 ppm of germanium. Reliability of the analytical method did not permit quantitative investigations since cad-Table I. Current Efficiencies Obtained at 0.0000 and 1.5000 G per Liter Cadmium Concentrations Ge Concentrastion,* Cd Concentration,* EtBclenoy, G per Liter G per Llter Pot 0.0000 0.0000 84.270 0.0010 0.0000 94.849 0.0050 0.0000 92.649 0.0075 0.0000 94.039 0.0100 0.0000 96.084 0.0000 1.5000 93.460 0.0010 1.5000 95.158 0.0050 1.5000 92.148 0.0075 1.5000 91.260 0.0100 1.5000 84.546 • Cd and Ge concentrations shown are those existing before zinc-dust purification. mium determination in the concentrations present in zinc-dusted solutions lacks sufficient sensitivity for reproducible results. As a consequence of the inability of the investigators to obtain acceptable results through direct quantitative analysis, an indirect approach was devised. This indirect method involved a study of the current efficiency, in a model zinc cell, as a function of the concentrations of cadmium and germanium. Variables such as cell temperature, voltage, current density, anode spacing, relative electrode area, degree of agitation, cathode preparation technique, time, acid concentration, and solution volume were held constant. Fig. 1 shows the cell used. The current was fur-

Jan 1, 1952

By B J. Beven, A Harris, L Balzan

Fortescue Metals Group flagship operation, Cloudbreak, is located in the Pilbara region of Western Australia. The mine is capable of delivering an annualised production rate of 40 Mt/a. Positioned 50 km to the east of Cloudbreak is Fortescue’s Christmas Creek operation, which has a combined processing capacity in excess of 50 Mt/a. Following on from these successes, Fortescue advanced development of its western Pilbara mines at the 60 Mt/a Solomon Hub. These processing installations place Fortescue in a strong position to deliver on a guidance of between 155–160 Mt/a for financial year 2014/2015.As Fortescue enters a phase of asset consolidation and debt repayment over expansion, the business is commanding stronger performance through enhanced plant operating practices and mine site cost reduction initiatives. To this end, the strategic placement of instrumentation is an area being given greater consideration. Access to real-time information pertaining to conveyed materials is of major interest to operators for making timely process control decisions. Fortescue has recognised the importance of accurate and up-to-date process information about their ores and hence, has adopted the use of Scantech’s Geoscan mineral analysers at two of their mines.There are two Geoscans at Cloudbreak; one on the ROM feed conveyor and another on the final product conveyor. These allow the in-feed material grade characteristics to be assessed. Moreover, the final product stream can be monitored to ensure product quality is maintained within acceptable quality tolerances. A third Geoscan is installed at Christmas Creek mine on a conveyor that transfers final products to Stockyards.This paper discusses the use of the Geoscans in these installations, including benefits to Fortescue’s operations, as well as functional considerations such as the impact of maintenance and calibration. A discussion of recent advances by Scantech is provided including enhancements to the calibration process and minimising plant downtime, along with a summary of results obtained.CITATION:Balzan, L, Beven, B J and Harris, A, 2015. Geoscan online analyser use for process control at Fortescue Metals Group sites in Western Australia, in Proceedings Iron Ore 2015, pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

E. G. Spilsbury, New York, N. Y.:—Do I understand correctly that the rolls are at first simple cylinders, one longer than the other, and that flanges are subsequently formed on the longer roll as the result of wear only ? Mr. Payne :—The flanges are formed by the wearing of the shorter roll into the other, which is about an inch longer. When the roll-shells are new, the longer one has machined at each end a ridge about 1/8 in. or 0.25 in. higher than the face. These slight projections help to center and steady the rolls, by locating the flanges in advance. Possibly they might be left off at the start; but Mr. Frazee has found it better, in machining the new roll-shells, to turn such small flanges upon the longer one. In his practice the feed-stream is extended a short distance beyond the two ends of the shorter roll-shell. This allows a small amount of crushing to be done between the flange-ftices and the vertical ends of the shorter roll-shell, which prevents any ridges from forming at the ends of the shorter roll-shell.

Jan 1, 1913

By Dale S. Preece

A Discrete element computer program named DMC @istinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural rock mass characteristics have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By G. Q. Liu

"The application of oxygen-enriched cyanidation to three Canadian gold ore samples has been investigated. The results showed that the use of oxygen can improve gold dissolution kinetics, reduce grinding time, and lower cyanide and lime consumptions. To obtain the same gold extraction, the required cyanide leaching time was reduced from 48 hours in slurry containing 8 ppm O2 to 12 - 24 hours in 20 ppm O2 slurry. Reagent consumptions were reduced by 23 - 37% for cyanide and by 35 - 54% for lime. There was little advantage to further increasing the dissolved oxygen to 32 ppm from 20 ppm. Gold extraction from the +200 mesh fraction improved 4 - 14% in oxygen-enriched slurry. A general kinetic model derived from the cyanidation of three ore samples can be described by the following equation: <equation>where E is the gold extraction (%) at time t (hours), EI is the ultimate gold extraction (%) , and &apos;P and k are constants depending on cyanide concentration, level of dissolved oxygen, and the characteristics of the ore samples. Comparative studies of conventional carbon adsorption and carbon adsorption in oxygen-enriched slurry have also demonstrated that oxygen enrichment resulted in more favourable conditions for gold adsorption."

Jan 1, 1995

By M. ROWE, H. E. Gilliland, L. BARNES

The authors of this paper are to be commended for a clear exposition of a timely subject. However, some important conclusions, in addition to those presented in the paper, can be drawn from the results of their elaborate and rather complete numerical computations. First of all, the major part of the calculations presented in the paper are for semi-infinite slabs of oil shale (the authors designate this as Model I) and a question must be posed — Are these elaborate computations needed to arrive at realistic estimates of the shale oil displaced. Consider the model of Lauwerier* that corresponds to the authors Model I if thermal conduction parallel to the fracture be neglected. If one also neglects the finite (but relatively small) heat capacity of the material in the fracture, it is easily shown from Lauwerier&apos;s solution that the cumulative oil production would be:

Jan 1, 1969

By H. D. Mendoza, M. J. C. Zerna

This study aims to determine the stability of Philippine nickel laterite ore by investigating the behavior of fine minerals of silica (dave=1.514 µm), hematite (dave= 0 1.351 µm), and nickel oxide (dave=1.426 µm) and their mixed-components in dilute aqueous suspension as a function of pH and electrolyte concentration. The zeta- potentials of the minerals are measured and stabilities of different component systems in aqueous suspension are determined. Hamaker constants of the minerals in aqueous medium are derived by getting their respective critical coagulation concentrations (c.c.c.) at stable pH conditions and at various concentrations of KNO3. The iso-electric points (i.e.p) for silica, hematite, and nickel oxide particles are at pH 2, pH 7.5, and pH 8.5, respectively. The stability behaviors of component systems are as follows: a) Silica dispersion is stable at pH range 3-11and unstable at pH 2; b) Hematite dispersion is stable at pH 2-5 and pH 8-11, and unstable near pH 7; c) Nickel oxide dispersion is stable at pH range 10-11 and unstable at pH 3-9; d) Hematite-silica dispersion is stable at pH range 6-11 and unstable at pH range 3-5; e) Hematite-nickel oxide dispersion is slightly stable at pH range 3-4 and unstable at pH range 5-11; f) Silica-nickel oxide dispersion is stable at pH range 10-11 and unstable at pH range 3-9; and, g) Hematite-silica-nickel oxide dispersion is stable at pH range 10-11 and unstable at pH range 3-9. The stability of nickel laterite ore is similar to that of the three-component system in an aqueous environment. The stability tests are analyzed using the classical DLVO theory. The stability conditions in an aqueous environment are essential in developing the appropriate process flow for the separation/ recovery of nickel laterite mineral components and also in the treatment of nickel laterite -laden wastewaters.

Jan 1, 2018

By Myrick N. Bolles

The concentration of gold and silver in mattes low in copper, and the subsequent separation and recovery of either or both of these metals, is a question the satisfactory solution of which has long vexed metallurgists. It covers a broad and important department of metallurgical science and brings in its train a series of attendant problems continuing from the initial operations of concentration to the final recovery of " values."

Jan 1, 1905

By M. Remillard, M. Garon, D. Hodouin, M. Therien

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami Division of Noranda Inc. have been sampled f or particle size distributions, chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMA T. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper cleaning flotation stages and to determine how over-all silver and three silver-bearing minerals are recovered in the plant final products. RESUMEDix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, leurs analyses chimiques et Ie contenu d&apos;argent et d&apos;or des fractions granulométriques. Le bilan métallurgique a été obtenu à l&apos;aide du programme BILMA T. Ces résultats, couples avec une étude minéralogique a fa microsonde, sont utilisés pour quantifier les pertes argentières aux diverses étapes de nettoyage du circuit de cuivre et pour déterminer la répartition de l&apos;argent et des trois minéraux argentifères dans les produits finals de l&apos;usine."

Jan 1, 1988

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015