Search Documents

By Claudia Ríos Figueroa, Gonzalo Montes-Atenas

"Among the many variables mentioned in the literature that may influence the froth flotation performance, particle size is perhaps one of the most renowned. Empirical knowledge has indicated that recovery of fine particles will inevitably drop below certain particle size threshold. Several processing alternatives have been suggested to improve the recovery of fine particles. Some of these initiatives have been reached the status of patents and other intellectual property related documents; however, there is still a disconnection between the scientific knowledge available and the industrial operations practicalities implemented to address this matter. In fact, in general terms, none of these ideas or processes concepts have become a final solution to this problem. At first glance, economical reasons may be argued as the main cause hindering the development of these and other ideas, but it would be an oversimplification as technical issues behind them are still themes to be discussed and sorted out. This study aims to review technical aspects behind scientific ideas and processes concepts suggested to solve the problem of low beneficiation of fine particles in froth flotation. The analysis was performed using the theory of inventive problem solving (TRIZ) which allows identifying technical gaps these initiatives have not considered or overlooked. Statistically the scientific databases indicates that reports on fine particles froth flotation only represented less than 50% of all reports involving fine particles processing. Most of the solutions derived from classic contradictions derived from bubbles and particles hydrodynamics only (reducing the bubble size or increasing the turbulence would increase the rate of bubble-particle aggregates formation but may reduce the recovery). This contradiction encompasses a small range of contradictions possible to be accounted and to be resolved. The method is expected to provide insights towards designing definitive solutions for the industry in this field."

Jan 1, 2014

By D. A. Woodford

A number of observations have now been reported where the steady-state creep rate is apparently linearly dependent on the applied stress at high temperature and low stresses. This results in a creep rate greater than that predicted by extrapolation of high-stress data and has obvious practical implications. However, some of these observations are open to question. For example, the analysis by Harris and Partridge17 of the data of Greenfield et a1.18 was dependent on strain rates which, according to the original authors, were too low to be measured. Dr. Bernstein appears to have demonstrated a linear stress dependence at low stresses in two zirconium alloys. There are, however, a number of discrepancies in his treatment of the data and the subsequent theoretical analysis which require clarification. 1) It is incorrectly stated that steady-state conditions are revealed by a slope of unity on a plot of log i vs log (time). This objection is trivial if the author meant to say a slope of zero, although it is unclear how subsequent extrapolation was made to determine the steady-state creep rates at low stresses for the zircaloy-2. If the plot used was actually log c vs log (time), it is unlikely that a slope of unity would represent a constant creep rate. A plot of log (c - co) vs log (time), where c0 is the extrapolated intercept sf the steady-state creep rate on the strain axis, would have a slope of unity during steady-state creep. However, eo cannot be determined unless is is already known. 2) The author chooses to interpret his results based on the equation: where A, and B, are structure-sensitive parameters, Ql and Q, are the activation energies for the particular creep process, and n describes the sensitivity of the creep rate on stress. The first term represents a slip creep process and the second a diffusion creep process. However, it is stated later that "two distinct processes acting in parallel are involved". Eq. [I] surely represents two processes in series since each reacts to the total applied stress and t, is the sum of the individual creep rates. If the processes are acting in parallel, then the effective stress in each would be less than the applied stress. The component stresses would be given by sl + s2 = a but it is not clear how the magnitude of either, or the corresponding stress exponent, could be determined.

Jan 1, 1969

By Hans S. Carlsson

Like most industrial processes, nuclear power production creates wastes, which have to be handled and ultimately disposed of in a safe manner. Some of the wastes contain very long-lived radioactive substances and have to be isolated for very long periods of time before they have decayed to harmless levels. Sweden, like many other countries with similar geology, intends to use crystalline rock for isolating the high-level nuclear waste from the biosphere. The suitability of a rock mass for a repository needs to be investigated extensively. Apart from the political and practical considerations for a site selection, a detailed study has to be performed in terms of geology, hydrogeology, geophysics, geochemistry and rock mechanics. The responsibility of the site selection studies in Sweden is entrusted to the Swedish Nuclear Fuel Supply Company, Division KBS (SKBF/KBS) . The paper gives a brief presentation of the "Standard Program" for the studies that will be carried out during 1980-1990. Modifications of the program are justified on the basis of gained experience or specific circumstances for each site. The program is compiled by the Geological Survey of Sweden (SGU) in cooperation with KBS.

Jan 1, 1982

By M. A. Ackerson, R. E. Griffin, W. H. Pomroy

Two automated fire detection system configurations have been used successfully in underground mines: the pneumatic "tube bundle" approach and the electronic telemetry approach. The electronic telemetry approach is more widely used, owing to its greater speed, flexibility, and capacity to both monitor other underground conditions, and remotely control underground equipment. However, depending on specific mine conditions and layouts, pneumatic detection, or a combined pneumatic/telemetered system may offer significant advantages over the telemetered approach alone. This paper describes research by the U.S. Bureau of Mines to design and in- mine test a rapid response pneumatic fire detection system tailored to the unique requirements of multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. A Bureau developed proto- type system is described with emphasis on design features which counter commonly perceived and/or experienced pneumatic detection system operating problems. Finally, the results of a 3-yr in-mine performance evaluation of the prototype hardware are discussed. Included are descriptions of system layout and coverage, response time, tube leakage, sample dilution, elimination of accumulated water from sample lines, and system maintenance and reliability.

Jan 1, 1989

By Pope Yeatman

In my experience, perhaps the most interesting problems came up during the testing, prospecting, developing and equipping of the Chuquicamata and Braden Copper Mines in Chile, and it is proposed in this article to give as briefly as possible what some of those problems were, their solutions, and the decisions made as to the different methods to be employed. The romance of mining is still a great lure to the young man who is making a choice of a profession to follow. The thought of travel to strange and out-of-the-way places, the glamor of pioneer life, the excitement of discovery, the constructive work of building something, entirely "from the grass roots up," or of reconstructing a played-out property and making a success of it-all of these phases have a strong appeal and often influence the young man in the choice of mining as a profession. That great engineer, Col. Seeley Wintersmith Mudd, whom we are endeavoring to honor, while having too much common sense to have been materially influenced by the romance of mining, certainly experienced all of the

Jan 1, 1932

By Christopher Mark

Mines with exceptionally low-strength roof (UCS <3,500 psi and CMRR <40) are much more likely to struggle with roof falls than other mines. Weak-roof is a particular problem for many room and pillar mines in the Midwestern and Northern Appalachian coal basins. Traditional roof support techniques are often not up to the challenge at these operations. This paper focuses on two mines, one operating in the Upper Freeport seam and the other in the Herrin No. 6 seam. Together, the two mines had more than 300 roof falls during a recent 5 year period. Each has experimented with a variety of roof bolt types and lengths, and with different supplemental supports. Detailed statistical analysis was conducted to determine which support combinations have proven to be most effective. Geology, horizontal stress, and time are also important at both mines. Successful control techniques have included; ? Identifying particularly troublesome lithologic roof units; ? Installing longer and stronger roof bolts; ? Installing supplemental support in intersections, and; ? Limiting the duration that a panel remains open. The lessons learned from these mines, and others like them, could help improve ground control safety for the entire U.S. mining industry.

Jan 1, 2004

By M. J. Southwood

SYNOPSIS Experiments carried out under atmospheric pressure and temperature (25°C) and sterile conditions show that the dissolution rate of nickel and copper from a pyrrhotite-pentlandite-chalcopyrite ore in a lixiviant of sulphuric acid is greatly enhanced in the presence of pyrite. At a pH value of 1,8 and in the presence of pyrite of equal mass to that of the ore, the recoveries of nickel and copper improved dramatically (21 and 80 per cent respectively). At a pH value of 4,0 the recovery of nickel was enhanced, but the chalcopyrite was refractory. A galvanic mechanism is probable, but cannot be proved from these experiments. The economic implications of the results are discussed.

Jan 1, 1985

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By George B. Holderer

The relation between man-hours of labor and production may be correlated for any industry, and already it has been widely used in piecework studies. It is not in general use as yet for recording labor efficiency of an enterprise or an industry. An exception to this is the Cement Institute, which tabulates the man-hours used in each operation and thus gets the total man-hours per barrel of cement. The writer knows of one steel company that keeps a complete record of man-hours for every operation from mining the ore to finishing the product. No doubt many others find the information useful, and such a study could be of value to the mineral industries.

Jan 1, 1937

By Y. Xi, T. M. Yegulalp

An availability approach for determining the capacity of a major Bucket Wheel Excavator (BWE) system to be used in the Yuabaoshan Surface Coal Mine in China is presented in this paper. Based on previous studies on other BWE systems for delay times due to internal and external causes and a four-level maintenance and repair schedule, a model was developed, taking into account all random failures, to present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity, are discussed.

Jan 1, 1994

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By P Breuer, A Simons

The sulfidisation, acidification, recycle and thickening (SART) process is currently being used at NewcrestÆs Telfer Gold Mine to recover cyanide and copper from the cyanidation tails of the pyrite concentrate carbon-in-leach (CIL) process. While the process has been effective at attaining high recoveries of cyanide and copper, the Telfer SART plant has experienced higher than expected sulfide additions to achieve these recoveries. This paper details the results of surveys on the Telfer SART plant, which show that residence time appears to be causing the high sulfide consumptions. The paper also details the results of laboratory scale experiments which confirm the observed residence time impact during the acidified stage of SART.CITATION:Simons, A and Breuer, P, 2013. The impact of residence time on copper recovery in Telfer Gold MineÆs cyanide recycling process, in Proceedings World Gold 2013 , pp 189-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By Newell Hamilton

Some years ago, in the manufacture of seamless tubing from an alloy steel containing 0.07 per cent maximum carbon, 18 per cent chromium and 8 per cent nickel, at the plant of The Babcock & Wilcox Tube Co., a peculiar type of piercing defect was noticed. This defect was definitely associated with certain heats of the alloy and was independent of any of the variables of mill operation and billet-heating condition. A thorough analysis of the defective material yielded but one clue to the reason for its abnormal behavior in piercing and that was its oxygen content as determined by the vacuum fusion method. The oxygen content of the defective 18-8 alloy was found to be from two to three times that of the material that had pierced satisfactorily, and this incited an active interest in the vacuum fusion method for the analysis of alloy steels. After a critical survey of the literature on this subject, and considerable experimentation, an apparatus and technique were evolved that gave a fairly rapid, simple and reliable method of analysis. Samples selected from six years of tube production of 18-8 and other corrosion-resistant alloys were analyzed by this method. This paper describes the procedure and gives a correlation of the oxygen, hydrogen and nitrogen contents of a number of alloy steel samples representative of good and bad tube-piercing quality. The Apparatus Basically the apparatus used in this work was that of Jordan and Eckman,&apos; employing a high-frequency induction furnace and the gravimetric method of analyzing the evolved gases, nitrogen being excluded from the determination. In addition, a magazine-type cap and a large-

Jan 1, 1934

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By Ibrahim Yusufoglu, Cem Kahruman, Mert Zoraga

In this study, a strontium sulfate mineral (celestite) was converted to strontium oxalate in solutions containing ammonium oxalate as a reactant. The experiments were carried out under isothermal conditions. The effects of stirring speed, ammonium oxalate concentration, particle size and temperature on the conversion rate were investigated. During the conversion process, definite volumes of solutions were taken from the reactor after different reaction times for the determination of sulfate ions using ICPOES. Fractional conversions of strontium sulfate were determined at different times and fractional conversion vs time diagrams were generated. It was found that the conversion of strontium sulfate was increased by increasing the ammonium oxalate concentration and temperature in addition to decreasing the particle size. The effect of stirring speed was negligible on the reaction rate. It was observed that above 328 K, a protective layer of strontium oxalate was formed on the strontium sulfate particles. X-ray Powder Diffraction technique was used for characterization of solid substances.

Jan 1, 2014