Search Documents

By C. A. Siebert, O. S. Duffendack, A. W. Herbenar

IN metallurgical problems involving the study of equilibrium in binary systems, the ,existence of an additional vapor phase, due to the presence of a volatile component in the alloy, has often been neglected. This is well indicated by the modified form of the phase rule, usually accepted in condensed systems in which pressure is not considered as a degree of freedom. In many cases the vapor pressure of the volatile component is exceedingly small and for all purposes can be considered negligible, in which case this form of the phase rule is applicable. However, alloys containing Hg, Cd, Zn, or Mg, tend to show very marked equilibrium vapor pressure, even in the solid state, and therefore present cases where the modified form of the phase rule no longer holds true. A quantitative determination of the vapor pressure of zinc in alpha brasses is not only of practical interest because of the loss of zinc in the processing of these alloys, but also of theoretical interest in that such measurements provide a means of applying the principles of theoretical physics and physical chemistry to problems of applied metallurgy. A number of investigators have reported vapor pressure measurements of zinc in alpha brasses. Hargreaves1 made extensive measurements which were used by Birchenall and Mehl² and Guttman³ for the determination of activity coefficients of zinc in alpha brasses. Hargreaves1 used a differentially heated quartz tube and measured the condensation temperature at one end corresponding to the temperature of the heated brass at the other end. Birchenall and Cheng outlined the condensation method of obtaining vapor pressure of zinc and Cd over some of their silver alloys." The primary object of the present investigation was to increase the range and accuracy of the vapor pressure data for the alpha brasses. Preparation of Alloys: Six alloys were prepared from Bunkerhill zinc and O.F.H.C. copper, both of 99.99 pct purity. The cast ingots were annealed for 24 hr at 550°C, scalped, cold rolled 40 pct and annealed for 50 hr at 550°C. The annealed bars were then surface ground and degasified for 30 min at approximately 550°C in an induction heated vacuum furnace. The surface of the bars was removed before milling the bars into relatively fine chips for chemical analysis and samples for the equilibrium cell. The analyses of the six alloys are given in table I. Experimental Method: The vapor pressure of zinc over the various alloys at a number of temperatures was determined from absorption spectra data. The spark source was produced by means of a high tension discharge between two electrodes of pure zinc. The design of the absorption vessel is shown in fig. 1. The vessel was constructed of transparent quartz which transmits the whole of the visible spectrum and the ultraviolet down to a wave length of 2000 A. The thickness of the vapor space was set at 0.8 mm so as to permit a relatively wide range of measurements without altering the vapor space, and thereby necessitating recalibration of the vessel. The furnace used for heating the absorption vessel consisted of a split wound furnace as shown in fig. 2. The spectrograph used in obtaining the transmitted zinc spectra was a double prism type especially designed for a region of 2500-3500 A. A step diaphragm used in conjunction with a tungsten filament provided the necessary intensity patterns required for calibration of the photographic plates.

Jan 1, 1951

By M. A. Mahtab, A. S. Burgess, R. G. Charlwood, P. O. Sandstrom, J. L. Ratigan

"Addressing a current operating and environmental concern, this paper first presents an overview of the design program for an underground radioactive waste storage vault. It then reviews the construction, operational and thermal-mechanical aspects of such a project. The relevant experience from major underground construction projects is reviewed and the paper concludes with brief comments on the design-oriented research and development requirements . 1. IntroductionA program to develop techniques for the ultimate disposal of high-level radioactive waste into geologic formations was announced by AECL in 1975 (Tamrnernagi, 1976), and is discussed more fully in a later document (Boulton, 1978). Our paper summarizes the studies caried out, as part of the AECL waste management program, by the authors and associates on the development of design concepts for a vault situated in crystalline rocks of the type present in the Canadian Shield.The design studies have been carried out in three phases, the elements of which are described in Section 2.1 (also see Fig. 1). The general vault designs are presented in Section 2.2. These provide for emplacement of either immobilized fuel or solidified reprocessing wastes in a room-and-pillar facility at a depth of 1,000 m.Section 3 reviews the principal design considerations from the construction, operation and thermal-mechanical response aspects. The concepts have been studied in both temporal and spatial domains, and the requirements and responses assessed in each as appropriate.Section 4 briefly reviews the availability of relevant experience from previous major underground construction projects. Finally, in Section 5, brief comments are given regarding design-oriented research and development requirements."

Jan 1, 1980

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

Discussion of the paper of L. W. BAHNEY, presented at, the New York meeting, February, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 339. to 344. E. J. HALL,* New York, N. Y. (communication to the Secretary+).- The Chiddy method for determining gold and silver in cyanide solutions has been subjected to so many proposed modifications, of which L. W. Bahney&apos;s is one, it is natural to suppose the method is defective. There is no denying that this method is capable of giving inaccurate results, but so is any other method of quantitative determination. However, proof has not come to my notice that the troubles are inherent and not in the detail application, and I am inclined to think from our experience that in many cases it is the latter. Errors in this method may be occasioned by: (1) The retention of zinc in the sponge, which tends to desilverize the molten lead in cupellation, similar to the action in the Parkes process, removing gold and silver in a crust of zinc oxide. Failure to remove zinc may result from lack of concentration of hydrochloric acid, clue to neutralization by salts present, volume of liquid too great for the specified amount of acid, or the use of weak acid. (HCl rapidly loses its strength unless kept in perfectly tight containers. The HCl gas escapes even from the ordinary glass-stoppered acid bottles after the plaster seal has been broken.) Undissolved zinc, is likely to be held in the upper part of the lead sponge, which floats above the liquid, and unless the solution is boiled it will escape action. Mr. Bahney&apos;s modification makes this

Jan 5, 1915

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

By J. L. W. Birkinbine

This paper is a discussion of a part of the mineral wealth of the States of Oaxaca and Paebla, Mexico. It does not refer to the precious metals, sonie mines of which, in these States, are said to have been worked before the advent of the Spanish conquistadores in the sixteenth century, as my purpose is to invite attention to the exploration of deposits of coal and iron-ores in the Mixteca region. The prominence given to coal is warranted by the great effect of the scarcity of fuel upon the industrial development of Mexico. Under the progressive administration of President Porfirio Diaz, the Republic has made wonderful advances in the past three decades; and this progress would have been greater but for the limitations imposed by expensive fuel. In the spring of 1906 I was detailed by the Birkinbine Engineering Offices, of Philadelphia, to accompany A. B. Adams, of New York, in a reconnoissance of reported deposits of iron-ores in the State of Oaxaca. The result of this expedition was the formation, in 1907, of the Oaxaca Iron & Coal Co., of which Mr. Adams became, and has remained, President and General Manager, and I have spent the past three years as Chief Engineer of this company in Mexico, principally in western Oaxaca, where field-headquarters were established. GEOGRAPHY AND POPULATION. Although the geographical and topographical features of the Republic of Mexico are well known, few realize that the majority of its population is domiciled in the States which immediately surround the capital city of Mexico, including the Federal District, Mexico, Tlaxcala, Morelos, Puebla,

Jan 1, 1911

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers&apos; errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author&apos;s name together with author&apos;s degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors&apos; & Printers&apos; Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King&apos;s English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the &apos;single&apos; type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x&apos; y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author&apos;s conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

By W. N. Poundstone, W. M. Merritts, B. A. Light

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining. This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g,.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes. In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased. Tests indicated that methane and water infused in bleeder holes traveled along the bedding planes of the Pittsburgh coalbed at a faster rate than across the planes. Methane associated with coalbeds is produced by the slow decomposition of carbonaceous material in the absence of air and the presence of water. It is lighter than air and, depending on its concentration, forms an inflammable or explosive mixture with air. It is believed that methane is entrapped in and around the pores of the coal and adjacent strata--often under great pressure. In many cases where the strata have been disturbed by geologic movements the

Jan 1, 1962

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proa[n]o hill are the Fresnillo mines, and it is marked now by a great gash cut by gloryhole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo. which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notable active in 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under Garcia&apos;s energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1833 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de benefacio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By Glenn R. Zellars, J. P. Morris

The carrier gas method was used to measure the vapor pressure of copper over liquid copper and Fe-Cu alloys. From these results, the activity of copper in the alloys was determined at 146°, 1550°, and 1600°C. Calculations of the activity of iron were made from the results for copper. The activities of copper and iron show strong positive deviations from Raoult&apos;s law. KNOWLEDGE of vapor pressures of liquid metals has both practical and theoretical value. Fuming of metal baths is directly related to vapor pressure, and the data should bc particularly important to the technology of vacuum metallurgy. Theoretical applications include determinations of heats of vaporization, heats of solution, and activity coefficients in alloys. Methods for measuring vapor pressures of metals have been reviewed by Speiser and Spretnak.&apos; High-vacuum procedures, such as the Langmuir and Knudsen methods, have been used most widely in recent years. However, these methods are not applicable to vapor pressures greater than lo-&apos; mm Hg and often cannot be used in the temperature range of greatest interest. The purpose of this investigation was to develop a procedure for measuring vapor pressures of pure metals and alloys that would be applicable to pressures greater than lo-&apos; mm Hg. The transportation or carrier gas method has been used. Copper was chosen for the initial work because its vapor pressure has been established fairly well and the reliability of the technique could be ascertained. Applicability to alloys was studied by determining the vapor pressure of copper over liquid Fe-Cu alloys. Experimental Procedure The tests were carried out in a graphite-spiral resistance furnace. The charge consisted of 50 g of metal contajned in a covered sintered-alumina crucible 1/2 in. deep and 13/8 in. ID. Two sintered-alumina tubes led from outside the furnace to within the crucible, passing through close-fitting holes in the crucible cover and radiation shield. The arrangement of the crucible and the two alumina tubes is shown in Fig. 1. The small-bore tube (1/16 in. ID by 5/16 in. OD) served as the inlet for the carrier gas. The tip of this tube touched the metal surface and the flow of gas imparted a rippling motion to the metal. In this manner the gas was brought into close contact with the metal and became saturated with metal vapor. In most of the tests the flow rate of the carrier gas was 560 ml per min, measured at room temperature. Approximately half of this saturated gas was allowed to escape from the crucible through the second alumina tube (3/16 in. ID by 5/16 in. OD) and was discharged to the atmosphere through a

Jan 1, 1957

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-&apos; had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.&apos; Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800&apos; to 1260°F (425&apos; to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800&apos; to 1000°F (425&apos; to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800&apos; to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590&apos; to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800&apos; to 1000°F (425&apos; to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,&apos; representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum&apos; for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,&apos; Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal&apos; and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :&apos;paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By R. Raines, S. P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6-m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor variations in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

By Eckley B. Coxe

THE plummet lamp, to which I called the attention of the Institute, at the Bethlehem meeting, in August, 1871, with the improvement of the compensating ring, suggested by Mr. Heller, having come into general use for mine surveying in this country, and my attention having been called to the fact that it could not be employed in mines in which there was danger of meeting with fire-damp, I have so modified it that it can be used in all cases with safety. Mining engineers, who are in active practice in those districts where fire-damp is met with in the mines (and I am sorry to say it is becoming much more common in the anthracite regions), know how dangerous their work is when they are called upon to survey such mines, particularly when they are obliged to run lines in those parts of a mine which have been unworked, since by opening of doors, brattice, etc., to get the sights, they are liable to disarrange the currents of air, and cause any fire-damp that may have accumulated in the old workings to find its way into the levels, etc., where the party is at work. It is, therefore, very dangerous to leave an open light (such as the original form of plummet lamp) in an old breast or gangway, even when the safety lamp has shown that no fire-damp is present, for the opening of the doors, etc., may drive the fire-damp to the light, and thus endanger the lives of the engineers. The improved form of plummet lamp, now shown to you, can be used either with or without the safety apparatus. Upon the top of the plumb-bob portion of the old lamp a screw is cut, upon which a ring A is screwed. (See Plate II.) On the external cylindrical part of this ring two small conical holes are drilled, 180° apart. The compensating ring, by which the plumb-bob part of the lamp is suspended, passes over the ring A, and is fastened to it by two small screws having conical points, which fit into the conical holes in the ring A. The safety apparatus resembles, to a certain extent, that of the Mueseler lamp. It consists of a ring B and plate C, which are united by four rods. The plate C has a cylindrical hole in the middle, and four apertures distributed radially around it. In the central cylindrical hole is fitted a conical brass chimney, which projects below the plate C, and is fastened to the latter, being kept ver-

Jan 1, 1875

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :&apos;paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By W. R. Opie

The object of this paper is to show the manner in which typical electrodeposits of hexagonal-close-packed metals—zinc, titanium, and zirconium—tend to form. The conditions of electrodeposi-tion markedly affect the nature of the deposits in regard to crystal size, orientation, and appearance. No attempt is made to correlate cell conditions with deposit quality but, rather, characteristic types of deposits were selected and a study made to show the relationship between outward appearance and crystal structure. The zinc deposits were made in aqueous electrolytes and the titanium and zirconium deposited from fused salt baths. ZINC deposits studied were made in the American Smelting and Refining Co.&apos;s Central Research Laboratories. They were representative of bright, shiny, smooth deposits, which can be obtained by using proper current densities and electrolyte addition agents, and of deposits which are dull and tend to be nodular. Four deposits were selected which ranged from smooth and bright to very nodular and dull, and their classifications are shown in Table I. These were examined microscopically and were found to differ quite markedly in outward surface structure and in microstructure. The outward surface variation is illustrated in Figs. 1 to 4. At X50 the texture could be seen to progress from granular to platelike to smooth. The microstructures of the deposits&apos; cross sections from starting sheet to outer surface are shown in Figs. 5 through 8. The dull nodular deposits (sample Nos. 1 and 2) show some tendency for acicular growth. The platelike sample (No. 3) shows tendency for columnar growth development and the smooth deposit (No. 4) has a well developed columnar structure. Back-reflection X-ray patterns of the deposit surfaces revealed some interesting information. The crystal orientation was random in all deposits except the smooth deposit. Fig. 9 is a typical back-reflection pattern of a nodular deposit. All planes are reflecting in the proper relative intensity. The pattern of the smooth deposit is shown in Fig. 10. The only planes which reflect are the (10.4). This series of planes is in the right position, with the FeKa radiation used, to satisfy the Bragg equation if the basal planes {00.1) are at right angles to the X-ray beam. The results were interpreted to mean that in the bright smooth deposit preferred orientation has occurred with the basal hexagonal planes oriented in the plane of the sheet but with all other planes randomly oriented around the c-axis.

Jan 1, 1957