Search Documents

By Norman Brown

It is suggested that the difference in ease of cross-slip among the fcc metals determines the relative amounts of [111] and [100] wire texture which occur in each metal. Since the ease of cross-slip is controlled by the stacking fault energy, it turns out that the amount of [111] texture should increase as the stacking fault energy increases. Arguments and existing data are presented to support the above suggestion. THE fcc metals generally have a dual texture, [11 and [loo], after wire drawing. As yet no fundament explanation exists concerning the variation of the amounts of each texture among the metals. Barrett&apos; has compiled data which show how the relative amounts of each texture vary from 100 pct [Ill] in the case of aluminum to 25 pct [l1] for silver. In this paper it is suggested that the value of stacking fault energy plays a major part in determining the amount of each type of texture. The double texture has its origin in the classical rotation of a single crystal under tension. An equilibrium position of the crystal is one in which three or more equivalent slip systems are operating simu taneously. Most crystals, initially, tend to rotate toward the [1ll] or the [l00] pole depending upon its initial orientation. This single-crystal behavior is essentially the same as the rotational behavior of the polycrystalline metal as worked out by Taylor.2 The next point to consider is whether the [Ill] or [100] orientation is more stable. There have been many discussions of this question3&apos;" which, in general, have lead to the conclusion that 11111 is most stable. For example, Pickus and Mathewson 4 suggested that a [Ill] texture produces more effective flow becake the [ 110] slip direction makes a smaller angle with the [111] than with the [loo]. A crude statistical argument will be presented which again favors the (1111 orientation. In order to maintain a pure [loo] wire texure, slip must occur in equal proportions in four of the six possible <110>slip directions. In order to maintain a pure [Ill] texture, slip must occur in equal proportions in only three of the six <110>directions. Since the <110> directions are the only slip directions in a fcc metal and if it is assumed that each of these six directions is equally probable, then the relative probability of a [1ll] texture vs a [l00] texture may be calculated. The statistical weight of a particular texture is the multiplicity of a texture times the probability of obtaining any one. The statistical weight for [Ill] is

Jan 1, 1962

By A. H. Geisler, R. F. Mehl, C. S. Barrett

The complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.l It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to he drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the 0 phase, "CuAl2." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in 0 lying parallel to this plane are roughly similar to those opposite it in the matrix.3 The formation of 0, however, is preceded by the formation of a transition lattice 0&apos;: which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly periect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.&apos;8 Particles of 0&apos; may be recognized microscopically and form a well-defined Wid-manstatten figure.* The 0&apos; lattice is recognized by the occurrence of diffraction lines on powder photo-grams or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6, 7, 1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a lew hundred atoms in diameter, probably of the composition of " CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact ?&apos; in a high State of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.l It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to he drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the 0 phase, "CuAl2." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in 0 lying parallel to this plane are roughly similar to those opposite it in the matrix.3 The formation of 0, however, is preceded by the formation of a transition lattice 0&apos;: which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly periect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.&apos;8 Particles of 0&apos; may be recognized microscopically and form a well-defined Wid-manstatten figure.* The 0&apos; lattice is recognized by the occurrence of diffraction lines on powder photo-grams or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6, 7, 1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a lew hundred atoms in diameter, probably of the composition of " CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact ?&apos; in a high State of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By W. J. Wolfe

Using a combined fire assay-atomic absorption method, gold determinations with a minimum detection limit of 5 ppb were made on 345 samples of Early Precambrian felsic plutonic rocks collected 2 2 from intrusions ranging in size from 4 km to 88 km and in composition from syenite to granodiorite. Gold levels in unmineralized stocks are consistently below the 5 ppb detection limit of the analytical method used. In contrast, analyses of samples from stocks containing gold mines within their borders and in nearby metavolcanic-metasedimentary host rocks show a strongly skewed trace element gold population with a substantial percentage of gold values exceeding 5 ppb and ranging as high as 320 ppb. The data indicate that (1) ore-stage hydrothermal metasomatism has produced widespread Au enrichment in Precambrian intrusions that host epigenetic vein-type gold deposits, and (2) geochemical Au analysis of samples collected from 30 to 50 randomly distributed sites can be used to estimate the gold exploration potential of stock-sized bodies and to outline internal patterns of Au variation which may be useful in directing exploration to particular contacts or portions of a stock. The results do not conclusively indicate unusually high Au content in primary unaltered igneous rocks.

Jan 1, 1975

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.&apos; Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,&apos; is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By John E. Udd

In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the writer visited key officials and institutions in Canada, the USA, the Republic of South Africa, the United Kingdom, Germany and Poland. Material from the Australian province of New South Wales and Hungary was also included. The report that resulted included, among other sections; (1) the history of wire rope and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements as regards safety factors; (4) a review of the players and the inspection practices; (5) the criteria for rope replacement; (6) a look into the future to outline the developments that could take place in both hoisting and rope inspection practices in Canada; (7) recommendations. Subsequently, the report was issued as a book by OMOL, and as a CD-ROM by the Mining and Mineral Sciences Laboratories, Natural Resources Canada. In this paper the author presents the key findings and the recommendations made in the study.

May 1, 2003

By D. M. Walters, C. M. van der Vyver, L. J. deVulliers

The occurrence of underground fires in narrow tabular ore- bodies where high density timber support is used is a dangerous and disruptive occurrence. The containment and extinguishing of the fire remains a very important consideration in reducing not only the loss in production time but also in limiting the extent of the area damaged by the fire. Mindful of this, Gold Fields have adopted and developed the inert gas generator system from its origins in Poland for use in Group precious metal mines. The system generates an oxygen- deficient atmosphere which is introduced in the fire area after this has been sealed. A number of problems had to be overcome to operate this system successfully within the infrastructure of these mines. Of particular significance is the operation of a jet engine, the prime component of the system, at air pressures encountered below sea level. The modifications have been found to be satisfactory to the point where, since 1992, ten underground fires have been extinguished using this system. Invariably, the areas affected by these fires were extensive (over 1 000 000 m3) and required continuous operation of these units over extended periods of time (in some cases in excess of 400 hours).

Jan 1, 1997

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

Methane predrainage from coal seams in the Western Area of the U.K. has been practiced over the past decade. The differing reasons for the practice include the controlling of gas emission rates in coal headings required to win out coal faces and also the need to control the gas emission rates in the roadways of retreat faces in order to comply with the statutory requirements. There are some similarities with predrainage experience in the Bulli Seam NSW. The several case studies highlight the varying conditions in the Western Area coalfield where the use of predrainage was Required.

Jan 1, 1982

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By R. Rocca, M. B. Bever

THE adiabatic elastic deformation of a body is accompanied by a change in temperature. This phenomenon is known as the thermoelastic effect. Under adiabatic conditions the temperature of a metal bar is decreased by an elastic elongation and is increased by an elastic compression. All materials which elongate on heating behave in this manner. The sign of the thermoelastic temperature change is reversed for the few materials which have a negative coefficient of thermal expansion. The following equation for the thermoelastic effect can be derived from fundamental thermody-namic theorems, as shown in the Appendix: dT8 =-a1/cs T dss [1] Cs In this equation, T is the absolute temperature, S is the entropy, a, is the coefficient of linear thermal expansion, cs&apos; is the heat capacity per unit volume at constant stress and s is the stress (positive in tension). Eq 1 can be applied to small, but finite changes in stress in the following form: ?Ts =- a1/cs T?ss [2] The sign of the temperature change AT is opposite to that of the change in stress s for materials which have a positive coefficient of thermal expansion. Eq 2 has been verified for many different materials and stresses at room temperature. No previous publication appears to have been devoted to an in- vestigation of the thermoelastic effect over a range of temperatures. Review of Literature Lord Kelvin (W. Thomson) presented a general theory of the thermoelastic effect in 1851&apos; and later applied it to a solid, subject to an arbitrary system of stresses&apos;. His analysis was based on a cycle of isothermal and constant-strain transformations and led to Eq 2 above. Even today, one of the clearest expositions of the thermoelastic effect is found in Lord Kelvin&apos;s article on elasticity in the Ninth Edition of the Encyclopedia Britannica (1878). R. ROCCA, Junior Member, and M. B. BEVER, Member AIME, are Research Assistant in Metallurgy and Associate Professor of Metallurgy, respectiuely, Massachusetts Institute of Technology, Cambridge, Mass. AIME New York Meeting, Feb. 1950. TP 2760 E. Discussion (2 copies) may be sent to Transactions AIME before APT. 1, 1950, and is scheduled for publication Nov. 1950. Manuscript received Oct. 15, 1949.

Jan 1, 1951

By D. Roberts

SUMMARY In order to accommodate a new plant in a limestone quarry in the Mendip Hills, it became necessary to excavate a potentially unstable disused face of the quarry. A simple two-dimensional graphical method was used to analyse a failure, which occurred during a period of exceptionally heavy rain in 1968, and the results of this analysis were used in estimating the stability of the proposed excavation. The presence of water in vertical fissures and tension cracks was found to be a dominant factor in determining the stability of these faces. The results of this approximate analysis were used as a guide in deciding upon the final slope design and the purpose of presenting this example is to illustrate how the various factors involved in arriving at this design were weighed to arrive at a compromise between theoretical recommendations and practical considerations. INTRODUCTION The successful outcome of a geological and geochemical survey to prove adequate re- serves of high quality limestone, suitable for producing burnt lime, led to planning for the installation of the necessary plant at Amalgamated Roadstone Corporation&apos;s Batts Combe Quarry at Cheddar in Somerset. Topographic and property boundary limits added to restrictions which were likely to be imposed by any forthcoming planning consents and restricted the choice of plant location to one site. The particular site is, in fact, the main floor area of the original quarry which, like many hillside quarries, had been worked with just one face. Before a benching scheme had been introduced on higher ground, the original face had attained a height of 230 ft. and sloped at angles of 58º to 64º. Fig. I shows the present configuration of the disused quarry face and the present working area above. The floor area below the disused face accommodates the existing crushing, conveying, and screening plant. The new facilities for lime burning are to be in addition to the existing main line business of producing roadstone and concrete aggregates and, although a new aggregate production plant would be included in the new installation, no disturbance of current production was to be contemplated.

Jan 1, 1972

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

By H. Kamiya, H. Hasegawa, M. Nojiri, S. Matsui, Y. Fukuda, M. Tsukada

"The present paper focuses on the action mechanism of anionic polymer dispersants in dense Si3N4 and SiC suspension. An atomic force microscope (AFM) was used to determine the relationship between the macroscopic suspension viscosity and the microscopic adsorbed structure of a polymer dispersant at the solid / liquid interface. The surface interactions within the suspensions were analyzed in various dispersant pH and additive conditions. The addition of an anionic polymer dispersant decreased Si3N4 and SiC suspension viscosity and increased electro-steric repulsion force on the non-oxide surface in solution at pH> 6 which was the isoelectric point of the materials. It was assumed that the increase of repulsive force was promoted by a hydrophobic adsorption of polymer dispersant on the non-oxide particles.IntroductionThe surface of silicon nitride and silicon carbide powders in a water suspension system has quite a complex molecular structure. In the case of Si3N4, hydroxyl and ammonium groups form on the surface and the pH of the suspension is increased from neutral to about 10 due to surface oxidation. The particle surface is negatively charged in alkaline solutions (pH=10), because the isoelectric point of silicon nitride exists in the pH range from 5 to 6. However, in spite of charging the negative surface charge, an anionic polymeric dispersant is generally used for the reduction in slurry viscosity.In dense SiC suspensions, an anionic polymer dispersant is generally used in order to disperse aggregates and reduce the suspension viscosity, too. Since an anionic dispersant is used in alkaline solutions higher than the isoelectric point of silicon carbide, the dispersant adsorbed on the negative charged surfaces of SiC.Few researchers have discussed and estimated the adsorption mechanism and structure of anionic polymeric dispersants on silicon nitride and silicon carbide surfaces. This is because it is difficult to observe the structure and measure the interaction at the solid/liquid interfuce directly. However, new developments in surface-force measurement technology have enabled the determination of non-DLVO type interaction for analyzing aggregation behavior2. The use of the AFM for analyzing the effects of various surfactants and co-polymers on colloidal dispersions and solid surfaces has also begun to rapidly expand to characterize the interaction between solid surfaces."

Jan 1, 2000

By W. L. Korbee, P. Hazebroek, M. Prats, E. E. Allen, C. A. 225-000-000-017 Verbraak, H. C. van Elst

In a recent paper,&apos; one of us has presented some experimental evidence on the relationship between twinning and brittle fracture in steel. From metallographic examinations of brittle fracture it could be derived that mechanical twins and microcracks are formed already in front of a running brittle fracture. A tentative explanation based on the evaluation of the statistical distribution of mechanical twins vs various angles to the fracture was given in the above mentioned paper. It was suggested that these twins are caused by stress waves emitted by a running brittle fracture. With the aid of high-speed photography and the use of photo-stress sheet we are now able to study in more detail the propagation of a brittle fracture and the emittance of stress waves connected with fracture. A typical example is given in Fig. 1. In this figure a running brittle fracture in an ordinary Thomas steel is shown. The experiment was performed on a Robertson apparatus and the stress waves caused by the fracture were made visible with photo-stress

Jan 1, 1962

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980