Search Documents

By Sathit Tandanand

Massive roof overlying the working seam in longwall operations can cause hazards if it does not cave readily behind the face supports. The overhang thus formed can overload the supports and endanger personnel when it collapses suddenly as a large rock mass. This Bureau of Mines report proposes the use of a concentrated load, either strip or point loading, applied onto the roof with the help of the upward thrust of the face supports. An experiment was conducted in the laboratory to obtain information about break characteristics and the values of significant parameters of three sedimentary rocks. The results were used to determine the breaking load requirement for a strong roof possibly encountered in typical longwall operations. The results show that the roof slab of moderate thickness can be fractured within the load capacity of off-the-shelf powered supports.

Jan 1, 1979

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By Clarke DS, Sporli KB

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins.The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By Alain Jardy, Valerio De Felice, Jean-Pierre Bellot, Ismael Lis Alves Daoud, Stephane Hans

"Gas-stirring ladle treatment of liquid metal has been pointed out for a long time as the processing stage mainly responsible for the inclusion population of specialty steels. A steel ladle is a complex three-phase reactor, where strongly dispersed inclusions are transported by the turbulent liquid metal / bubbles flow. We have coupled a population balance model with CFD in order to simulate the mechanisms of transport, aggregation, flotation and surface entrapment of inclusions. The simulation results, when applied to an industrial gas-stirring ladle operation, show the efficiency of this modelling approach and allow us to compare the respective roles of these mechanisms on the inclusion removal rate.IntroductionThe reduction of the weight of high performance materials together with the improvement of mechanical properties and the increase of the recycling of used metal are new challenges which emphasize the importance of metal cleanliness. Ladle treatment of specialty steels has long been described as the secondary metallurgical process mainly responsible for the non-metallic inclusion derived from the deoxidation process. The treatment is accomplished by blowing argon through one or more porous plugs for the purposes of desulphurization, minor composition adjustments, and inclusion removal. Gas injection is applied on routine basis to achieve both the stirring of the liquid bath (thermal and chemical homogenization) and the entrapment of the inclusions by the bubbles (flotation). Furthermore, the turbulence produced in bubble swarms enhances the probability of inclusion collisions and makes aggregation the first mechanism for particle removal. The physical processes involved in gas stirred ladles are numerous and complex owing to the three dimensional and multiphase (metal-gas and inclusions) nature of the reactor. Despite these difficulties, the population balance equations can be implemented in CFD code11'21 and combined CFD-PBM (computational fluid dynamics - population balance method) models are investigated for steel ladle processes13'41 and produce very promising results in terms of inclusion removal efficiency."

Jan 1, 2012

By J. Bruce Wagner, Roger L. Levin

Integrated forms of two solutions of Fick's second law for the movement of a plane interface through a sample of wustite, and for diffusion into a semi-infinite slab of wustite, are shown to yield nearly identical values of the chemical diffusion coeffcients of cation vacancies in wustite, over the temperature range 900° to 1100°C. The chemical diffusion coefficients, the values of D obtained for the propagation of a concentration gradient through samples of undoped and doped wustite, are obtained from the equations It is becoming increasingly important in metallurgical practices to understand the role of the chemical diffusion coefficient, i.e., the diffusion coefficient of a species across a concentration gradient. During the first stages of sintering, one of the mechanisms by which the bonds between neighboring particles develop is by volume or bulk diffusion. This diffusion coefficient as deter- where ?m is the weight change at any time t, ?W is the total weight change at t =8, A is the area of the specimen, and AC is the total change in the cation concentration after the establishment of equilibrium, as determined by reduction experiments in different carbon monoxide -carbon dioxide mixtures within the limits of existence of the single-phase field. mined from the standard equations for volume diffusion during sintering is actually a chemical diffusion coefficient, and it has been observed to be many times larger than the self-diffusion coefficient as determined on the same materials by experiments using radioactive tracer techniques. Kuczyn-ski1 has noted that, if the controlling mechanism of sintering of A12O3 in an oxidizing atmosphere is the diffusion of oxygen, then this diffusion coefficient as measured from sintering rates is about 2.2 x 104 higher than the self-diffusion measurements obtained by tracer techniques. He has also reported the diffusion coefficient obtained from the rate of sintering of Fe2O3 powder to be about 10 6 times faster than the self-diffusion coefficient of

Jan 1, 1965

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By H. O. Hofman

Lime-roasting is a term proposed by Ingalls&apos; for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse un-decomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale,—the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent. of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1908

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,&apos; who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By Robert Rennie, Taylor Davies, Ahsanul Rafi

Electric locomotives powered by extensive electrical cabling systems were prevalent in the mining industry in the early days of the 20th Century [1]. Since the movement of tethered electrical mining locomotives was limited, the advent of diesel-powered mobile mining equipment provided more flexibility. This led the mining industry to be dominated by diesel-powered locomotives for most of the 20th Century and the entire 21st Century, to date. However, diesel power has certain drawbacks. Diesel-powered vehicles produce tailpipe emissions such as diesel particulate matter, carbon dioxide, sulfur dioxide, and nitrogen oxide. Mine workers exposed to these emissions were, and continue to be, subject to health issues such as respiratory problems, increased risk of lung cancer, and cardiovascular disease. [2][3]. Extensive ventilation systems are required to dilute the diesel exhaust and dissipate the heat generated by these vehicles. Moreover, as mines are getting deeper due to depleting resources, ventilation costs in diesel-powered mines are becoming increasingly high. These factors, coupled with the trend towards greenhouse gas (GHG) reduction in mine operations, has allowed zero-emission electric locomotive systems to gain traction. As lithium-ion battery technology is becoming more advanced, battery-powered electric vehicles can now perform duty cycles comparable to those of diesel-powered vehicles. Although battery-electric vehicles (BEVs) are comparable to diesel-powered vehicles in terms of mobility, they have certain limitations. For instance, the amount of onboard energy is limited by the battery energy density and specific energy. The MT42 diesel haul truck from Epiroc, for example, has a fuel tank capacity of 580L, which is equivalent to around 1450 kWh of net electrical energy [4]. The electrified version of the MT42, on the other hand, has an onboard battery with 375 kWh of usable energy weighing around 4.9 metric tonnes [5]. Moreover, storing and refueling of diesel-powered vehicles is simple and quick, whereas battery energy storage and charging systems require extensive infrastructure development. Charging time is mostly limited by battery chemistry and design. Due to these limitations, the benefits of battery-powered mining vehicles are more likely to be realized with proper planning and optimization of the BEV fleet. This includes optimizing mining layouts for BEV use, charging infrastructure design, and management of onboard energy storage systems.

Jun 25, 2023

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

By Holly J

Mr. Champness: I wish to congratulate the authors on their paper, which covers a large variety of subjects. Not every mine is in the fortunate position to effect cost reductions by the sinking of a new shaft, but, as the authors have endeavoured to show in their paper, with improved techniques further reductions are possible. I would like to ask two questions. Can the authors give me an approximate idea...

Jan 1, 1956