Search Documents

By H. Hayashi, M. Yamaki, H. Hashimoto, T. Yamanashi

"In an experiment on a trial embankment, the deformation mode of the improved ground at the toe of the embankment was compared with the deformation mode of the unimproved ground. This comparison showed that the behavior exhibited by the improved ground was the same as that exhibited by the unimproved ground, despite the low improvement rate (ap = 10%) of the ground improvement. Thus, the improved ground and the unimproved ground were found to be functioning as composite ground. Further, the strain that developed in the geo-textile used for the crushed-stone mat was considerably less than the strain specified by the design strength. As a result, it was found that a crushed-stone mat can serve as a mattress.OVERVIEW OF THE TEST CONSTRUCTIONLow Improvement-Rate Soil in Combination with Crushed-Stone MatIn Hokkaido, approximately 2,000 km2 of the land is peat land, an area almost as large as Tokyo. Such land accounts for 6% of Hokkaido’s plains and 2.4% of its total land area. The peat layer is normally 3 to 5 m thick and underlain by a layer of soft, cohesive soil whose thickness may exceed 20 m. In such a ground, consolidation using cement may generate differential settlement between improved soil as a result of embankment construction or lateral deformation caused by the slipping of unimproved ground. Therefore, the improvement ratio (ap) is designed to be at least 50% by the Manual for Construction on Soft Peaty Ground (CERI, 2011 [1]). Consolidation of ground with a low improvement ratio in combination with crushed stone-mat installation is a measure for soft ground (Figure 1). In this method, soil with a lower Improvement ratio than that of conventional improved soil (e.g., ap=10%) is placed beneath the entire embankment and a “crush stone mat”, a layer of crushed stone (t=0.5 m) enclosed by geo-textile, is then placed between the embankment and the soil."

Jan 1, 2015

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By H. W. Page

Petroleum requirements since V-J day have been appreciably higher than predicted. Foreign operations now exceed maximum wartime levels by about 14 per cent. Domestic operations since V-J day have averaged 92 Per cent of the wartime peak. In spite of maximum foreign refinery runs, large exports of all products, except residual fuel oil, are necessary to meet foreign demand. During the next few years it is expected that foreign operations will continue at capacity, including new installations, but that, because of increases in foreign demand, exports will continue at about their present level. Domestic operations will increase during this period and crude production probably will exceed maximum efficient rates. Even after 10 years some exports probably will be required, but eventually these will be supplanted by increased output of foreign refineries, except for small tributary exports. The increase in domestic requirements will exceed the decline in exports. Unless findings of crude oil exceed present expectations, the increasing demand will be met by increased imports and synthetic methods-—such as the Hydrocarbon Synthesis Process for conversion of natural gas and coal to gasoline and distillates. Catalytic cracking installations will increase as crude availability decreases. This will help to meet the increasing demand for gasoline but will intensify the domestic shortage of residual fuel oil. Eventually larger imports will be required to satisfy the demand for this product. Introduction Under the pressure of the wartime period, there was time only occasionaly to look ahead in anticipation of what the postwar era held for the petroleum industry. Perhaps the general expectation was that a rather pronounced decline in the level of industry petroleum operations would take place shortly after the end of the war, with the impact felt mainly on the economy of the United States- It is of interest now, nine months after V-J day, to take inventory of the near-term situation and see what significant forces are at work. With this as a starting point, it should be possible to engage in something more satisfactory than pure speculation concerning trends in the immediate future and 10 to 20 years ahead. Present and Near-term Situation During the nine-month period following V-J day, foreign crude oil production and rebery operations have actually increased the These activities were at maximum capacity on V-J day but the continuation of drilling programs, the completion of new and rehabilitated refineries and of transportation facilities during the Past nine months have increased the foreign capacity. This added capacity has been fully utilized. Foreign crude oil production in May 1946 is about 14 per cent higher than during July 1945 and refining operations some 12 per cent higher' During the same period there has been a falling off in similar activities within the

Jan 1, 1947

By A. A. B. Douglas

In this paper the origins of the mortar intruded concrete concept and its development and application in the construction of watertight bulkheads in South Africa are described. The events leading to the commissioning and execution of the West Driefontein Experimental Plug and the Virginia/Merriespruit Boundary Plugs, and their roles in the proving of the technique, follow. The development of the first Transvaal and Orange Free State Chamber of Mines Code of Practice for Mortar Intrusion Concrete for Underground Plugs and Bulkheads, Johannesburg, November 1962,is explained. The saga of the October 1968 flood and subsequent salvage of the West Driefontein Gold Mine is recounted. The paper concludes with mention of the validation programme carried out for the Placer Dome Western Areas Joint Venture and their South Deep water barrier programme.

Jan 1, 2006

By H. W. Page

Petroleum requirements since V-J day have been appreciably higher than predicted. Foreign operations now exceed maximum wartime levels by about 14 per cent. Domestic operations since V-J day have averaged 92 Per cent of the wartime peak. In spite of maximum foreign refinery runs, large exports of all products, except residual fuel oil, are necessary to meet foreign demand. During the next few years it is expected that foreign operations will continue at capacity, including new installations, but that, because of increases in foreign demand, exports will continue at about their present level. Domestic operations will increase during this period and crude production probably will exceed maximum efficient rates. Even after 10 years some exports probably will be required, but eventually these will be supplanted by increased output of foreign refineries, except for small tributary exports. The increase in domestic requirements will exceed the decline in exports. Unless findings of crude oil exceed present expectations, the increasing demand will be met by increased imports and synthetic methods-—such as the Hydrocarbon Synthesis Process for conversion of natural gas and coal to gasoline and distillates. Catalytic cracking installations will increase as crude availability decreases. This will help to meet the increasing demand for gasoline but will intensify the domestic shortage of residual fuel oil. Eventually larger imports will be required to satisfy the demand for this product. Introduction Under the pressure of the wartime period, there was time only occasionaly to look ahead in anticipation of what the postwar era held for the petroleum industry. Perhaps the general expectation was that a rather pronounced decline in the level of industry petroleum operations would take place shortly after the end of the war, with the impact felt mainly on the economy of the United States- It is of interest now, nine months after V-J day, to take inventory of the near-term situation and see what significant forces are at work. With this as a starting point, it should be possible to engage in something more satisfactory than pure speculation concerning trends in the immediate future and 10 to 20 years ahead. Present and Near-term Situation During the nine-month period following V-J day, foreign crude oil production and rebery operations have actually increased the These activities were at maximum capacity on V-J day but the continuation of drilling programs, the completion of new and rehabilitated refineries and of transportation facilities during the Past nine months have increased the foreign capacity. This added capacity has been fully utilized. Foreign crude oil production in May 1946 is about 14 per cent higher than during July 1945 and refining operations some 12 per cent higher' During the same period there has been a falling off in similar activities within the

Jan 1, 1947

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

By R. A. Sharma, F. D. Richardson

Manganese oxide acitivities and sulfide capacities have been measured at 1650°C in mixtures of MnO + A1203 and MnO + SiO2 - Al2O3. Sulfide capacities have also been measured at 165O0C for melts of MnO + SiO2, MgO + SiO2, MgO + SiO2 + Al2O3, MgO + MnO + SiO2, and SiO2 + Al2O3 and for crystalline CaO. The activity coefficients of the sulfides of manganese and magnesium have been derived where possible. It looks as though the activity coefficients of sulfides are greatest at compositions where the free energies of formation of the silicate mixtures have their maximum negative values. The amphoteric nature of alumina is reflected in the results for the binaries and ternaries in which it is present with silica. The limiting solubility of CaS in CaO at 1650°C is 6.3 x 10-4 mole fraction. THE activities of manganese oxide have been measured in a variety of silicate and aluminate melts by use of the equilibrium (MnO)slag = [Mn]pt .½O2 [l] and the experimental techniques described previously.' Sulfide capacities (CS = wt pct S (PO2/PS2)½) have also been determined in a series of melts, by use of an established method2 which exploits the equilibrium (O°) + ½S2 = (S") . ½O2 [2] If CS and the activity of a metal oxide are known in a melt, the activity coefficient of the metal sulfide can be calculated by use of the equilibrium constant K, for the pure phase reaction MO i ½S2 = MS + ½O2 [3] The activity coefficient of the sulfide is then given by the equation

Jan 1, 1965

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

By Larry Southwick

In the early 1940's, the Caron ammonia ? ammonia carbonate leach process was used to produce nickel from Mayari ores at the Nicaro plant in Oriente Province, Cuba. While plant operation was generally successful, it was not broadly economical and was shut down. The plant was later restarted in the 1950's and a number of investigations initiated to resolve the more serious operational and performance issues. Processing steps studied included iron reduction (chemistry ? nickel and iron, reductant, equipment), ore variability (homogeneity and consistency of mineral concentrations, serpentine vs. laterite), leach solution strength, nickel recovery (temperature ? reduction and leaching, reoxidation) and a variety of other topics. These studies and their findings will be discussed. Caron himself obtained good results on these ores in the laboratory. They could not be duplicated in the field, the reasons for which will be reviewed. (Note: the ore looked like garden dirt; charcoal made from palm trees was one of the reductants attempted; and ammonia was the leach solution. Mixing the three, so to speak, was to yield nickel.)

Jan 1, 2006

By Edward A. Barrett, Kathleen M. Kowalski-Trakofler

This paper discusses the application of a training intervention that uses degraded images for improving the hazard recognition skills of miners. Method: NIOSH researchers, in an extensive literature review, identified fundamental psychological principles on perception that may be employed to enhance the ability of miners to recognize and respond to hazards in their dangerous work environment. Three studies were conducted to evaluate the effectiveness of the degraded image training intervention. A model of hazard recognition was developed to guide the study. Results: In the first study, miners from Pennsylvania, West Virginia and Alabama, who were taught with the aid of degraded images, scored significantly better on follow—up hazard recognition performance measures than those trained using traditional instructional methodologies. The second and third studies investigated the effectiveness of the training intervention at two mining companies. Data collected over a3—year period showed that lost—time injuries at mines in Alabama and Illinois declined soon after the training intervention was instituted. Impact on Industry: Further exploration of the hazard recognition model and the development of other interventions based on the model could support the validity of the steps in the hazard recognition model.

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By G. N. Goldberg, Robert A. Rapp

The steady-state kinetics and microstructures of simultaneous internal oxidation and external scale formation were investigated for the oxidation of Cb-Zr and Ch-Zr-Re alloys in pure oxygen at 1000°C. For each binary alloy, a constant rate of scale formation was observed at steady state; the internal oxidatton zone reached a steady-state, time-independent thickness. The dependence of the scaling rate on zirconium content exhibited a maximum at a low zirconium colttent; more concentrated alloys oxidized at a slower rate than pure columbium. This composition dependence of the scaling rate may be partially attributed to the effect of the internal oxidation process as an intenla1 sink for oxygen, with the formation of voluminous, and relatively impermeable ZrO2 precipitates. However, the morphologies of the ZrO2 internal oxide precipitates also affected the scaling rate. The internal oxide precipitates were distributed uniformly in the external scale. The steady-state thicknesses of the internal oxidation zones were not in agreement with those predicted theoretically from an idealized simple model. However, in this particular alloy systen1 the ideal model is not satisfied experitmentally. For ternary Cb- Zr - Re alloys with Nr10e = 0.02 or 0.05, the steady-state thicknesses of the internal oxidation zones were less than those for the corresponding binary Cb-Zr alloys. For ternary alloys with NRe(0) - 0.05, a more adherent and much less porous external scale was formed, and a reduction in the kinetics of scale formation was observed. A number of authors'-7 have reported linear oxidation kinetics for the reaction of pure columbium at 1000°C in air or in oxygen of about 1 atm pressure. A thin and tightly adherent oxide layer is found at the metal/oxide interface beneath a porous external layer of scale. Although the suboxides CbO and CbO2 represent thermodynamically stable phases at 100O°C, generally only Cb2O5* is identified as a reaction product in quenched specimens. Studies at 1000°C at lower oxygen pressures8,10 (Po2 - 10-4 Torr) show that both CbO and CbO2 do form and that CbO2 is a protective oxide. The growth of CbO2 results in parabolic kinetics until Cb2O5 is nucleated and grows. Apparently because of the large volume change associated with its formation, Cb2O5 is porous and does not serve as a diffusion barrier; linear kinetics prevail after the surface is covered with Cb2o5. On the basis of these observations, several authors5,9,10 have suggested that the linear oxidation of pure columbium at 1000°C in air or oxygen of 1 atm is limited by a Loriers-type mechanism,11 whereby the total rate or reaction is controlled by ionic diffusion through a thin layer of CbO2 which is maintained at a constant thickness throughout the linear oxidation. However, the concept of a Loriers model for a three-phase CbOlCbO2 Cb2O5 scale, with the only oxygen activity gradient across the NbO2 phase, is not self-consistent. Further, the suboxides CbO and CbO2 were not observed in the high-temperature X-ray diffraction study of columbium oxidation by Goldschmidt.8 From investigations in which the large PO2, dependence of the linear scaling rate was demonstrated, the importance of an oxygen adsorption or dissolution step has been suggested.4,5,7,10,12 Thus the mechanism for the linear oxidation of pure columbium remains quite controversial. Since further insight into the oxidation mechanism of pure columbium is not provided by this investigation, the authors wish to emphasize at the outset that their experimental results are not interpreted in terms of a particular rate controlling step for the oxidation of pure columbium. Previous investigations13-18 of the oxidation of Cb-Zr solid-solution alloys in air or oxygen at 1000°C suggest a remarkable dependence upon zirconium content. For an alloy of bulk zirconium mole fraction, N2r(0) equal to 0.05 or 0.10, the oxygen uptake is reported to be as high as four times greater than that for pure columbium;13,14 for alloys with NZr(0) 0.05 or 0.10 the oxygen uptake is reported to decrease with increasing NZr(0); to a minimum uptake of about one quarter that for pure columbium at NZr(0): = 0.50.13-15Since zirconium forms a more stable oxide (ZrO2) than the lowest columbium oxide (CbO), and since columbium exhibits a high solubility19,20 and diffusivity21,23 for oxygen, the internal oxidation of the zirconium component to ZrO2 is expected at a reaction front ahead of the advancing metal/scale interface. The external scale is then formed at the metal/scale interface by the inward migration of oxygen through the scale, probably through a series combination of molecular and ionic diffusion. Internal oxidation in conjunction with external scale formation has been investigated by Maak24 for the oxidation of dilute Cu-Be alloys in pure oxygen at 850°C. For cu-Be and many other binary alloys,24-27 very small, essentially uniaxial internal oxide particles are formed in the most dilute compositions; for somewhat more concentrated alloys. the internal oxide particles precipitate as platelets or needles. From pertinent solutions to the diffusion equation, Maak28

Jan 1, 1967

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

By Allan J. Breitenbach

Heap leach operations provide a low-cost method for recovering gold, silver, and copper metals from low grade ore materials. The processed ore materials are stacked in controlled lifts on a lined pad facility for heap leaching. A controlled barren solution is applied to the heap ore surface by sprinkler or drip emitter irrigation, and ore metals are leached into the solution for collection and extraction in plant process facilities. The leach pad and solution collection facilities are lined with impervious materials for containment of all process solutions. The liner system typically includes a composite geomembrane and clayey soil liner with a protective drain cover fill to maximize solution recovery and protect the underlying groundwater conditions. This paper discusses the types of pad liner systems currently used by the mining industry and the "good, bad, and ugly" lessons learned in engineering practice over the last 10 years in the design and construction of heap leach pads.

Jan 1, 1999