Search Documents

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By H. K. Work, H. T. Clark

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By R. J. Fruehan, F. D. Richardson

Electrochemical measurements have been made of the activity of oxygen in copper and its alloys with silver and tin at 1100" and 1200°C. The galvanic cell used was Pt, Ni + NiO/solid ellectrolyte/[O] in metal, cermet, Pt The results do not support any of the equations so far designed for predicting the activities of dilute solutes in ternary solutions from activities in the corresponding binaries. If, however, a quasichemical equation is used with the coordination number set to unity, agreement between observed and calculated activities shows that this empirical relationship can be useful over a fair range of conditions. SEVERAL solution models have been proposed for predicting the activity coefficients of dilute solutes in ternary alloys from a knowledge of the three binary systems involved. Alcock and Richardson1 have shown that a regular model, and a quasichemical model,&apos; in which the dissolved oxygen is coordinated with eight or so metal atoms, can reasonably predict the behavior of both metal and nonmetal solutes when the heats of solution of the solute in the separate solvent metals are similar. But when this is not so, neither model gives useful predictions unless coordination numbers of one or two are assumed. Wada and Saito3 subsequently adopted a similar model to derive the interaction energies for two dilute solutes in a solvent metal. Belton and Tankins4 Rave proposed both regular and quasichemical type models in which the oxygen is bound into molecular species, such as NiO and CuO in mixtures of Cu + Ni + 0. However, their models have only been tested on systems in which the excess free energies of solution of the solute in the two separate metals differ by a few kilocalories. Ope of the reasons why more advanced models have not been proposed is because few complete sets of data exist for ternary systems in which the solute behaves very differently in the two separate metals. For this reason measurements have been made of the activities of oxygen dissolved in Cu + Ag and Cu + Sn. Measurements on both systems were made by means of the electrochemical cell, Pt, Ni + NiO/solid electrolyte/O(in alloy), cermet,Pt [1] The activity of oxygen was calculated from the electromotive force and the standard free energy of formation of NiO, which is accurately known.5 Before investigating the alloys, studies were made of oxygen in copper to test the reliability of the cell and to check the thermodynamics of the system. Of the previous studies those by Sano and Sakao,6 Tom-linson and Young,7 and Tankins et al.8,7 have been made with gas-metal equilibrium techniques; those by Diaz and Richardson,9 Osterwald,10 wilder," Plusch-kell and Engell,12 Rickert and wagner,13 and Fischer and Ackermann14 have been made by electrochemical methods. EXPERIMENTAL The apparatus employed was the same as described previously,9 apart from slight modification. The molten sample of approximately 40 g was held in a high grade alumina crucible 1.2 in. OD and 1.6 in. long. The solid electrolytes were ZrO2 + 7½ wt pct CaO and ZrO2 + 15 wt pct CaO; the tubes 4 in. OD and 6 in. long were supplied by the Zirconia Corp. of America. They were closed (flat) at one end. In one experiment with Cu + O, both electrolytes were used in the cell at the same time. The reference electrodes inside the electrolyte tubes consisted of a mixture of Ni + NiO. They were made by mixing the powdered materials and pressing them manually into the ends of the tubes, with a platinum lead embedded in them. The tubes were then sintered overnight in the electromotive force apparatus at 1100°C. By sintering the powders inside the tubes (instead of using a presintered pellet9) better contacts were obtained between the electrolyte, the powder, and the platinum lead. Troubles arising from polarization9 were thus much reduced. The electromotive force was measured by a Vibron Electrometer with an input impedence of 1017 ohm; the temperature was measured with a Pt:13 pct Rh + Pt thermocouple protected by an alumina sheath. The couple was calibrated against the melting point of copper. The cermet conducting lead of Cr + 28 pct Al2O3, previously found to be satisfactory9 for use with Cu + 0 was also found satisfactory with Cu + Ag + 0 and Cu + Sn + 0. Superficial oxidation was observed, but it did not interfere with the working of the cell. The reaction tube containing the cell was closed at each end with cooled brass heads and suspended in a platinum resistance furnace. The tube was electrically shielded by a Kanthal A-1 ribbon which was wound round it, and the ribbon was protected by a N2 atmosphere between the furnace and the reaction tube. The cell was protected by a stream of high purity argon which was dried and passed through copper gauze at 450°C and titanium chips at 900°C. All the metals used were of spectrographic standard. Procedure. In studies of the system Cu + 0, be-

Jan 1, 1970

By C. L. Sollenbeger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature1,2 to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent. In the All is-Chalmers Research Laboratories a systematic study was made of the effect of different alkali-silica ratios on the concentration by flotation of two scheelite ores. One of these was a high grade ore from the Sang Dong mine in Korea. The effect of such factors as pH; addition agents; and conditioning time, temperature, and pulp density on the flotation efficiency of this ore have been described previously. The other ore was a low grade ore from Getchell Mines Inc., Nevada. The mineralogy and techniques of concentrating this ore have been described by Kunze. Hereafter these ores will be referred to as the Korean and Nevada ores. Experiments were made with both to determine the effect of three factors—-type of silicate, concentration of silicate, and pH of the pulp—on recovery and grade of tungsten in a rougher concentrate. Average WO, content of the Korean ore was 1.50 pct and of the Nevada ore 0.27 pct. The predominant tungsten mineral in both ores was scheelite, which was accompanied by a small amount of powellite. The powellite and scheelite were finely disseminated through both ores and required a —200 mesh grind for liberation. Major gangue minerals in the Korean ore, in decreasing order of abundance, were amphi-boles, quartz, biotite, garnet, fluorite, and calcite. Bulk sulfides composed about 3 pct of the total weight. Gangue in the Nevada ore, in descending order of abundance, was garnet, alpha quartz, calcite, phlogopite, wollastonite, and amphiboles. Sulfide minerals were 3 to 4 pct of total weight. Batch flotation experiments were made with 500-g samples of ore, each sample wet-ground to 90 pct passing 200 mesh. The finely ground ore was floated in a Fagergren batch cell at 25 pct solids. The natural pH of the Nevada ore was 8.9 and of the Korean ore, 8.5. The D, RU, K, N, and S-35 sodium silicates were obtained in colloidal dispersions with varying amounts of water. The most alkaline, Metso, was in dry powdered form. For convenience in addition, 5 pct solutions by weight were prepared from each of the silicates, on the basis of dry sodium silicate dissolved in the correct amount of distilled water. Chemical analyses of the various silicates are given in Table I, together with the pH of the 5 pct solutions. A preliminary bulk sulfide float was made with secondary butyl xanthate as the collector and pine oil as the frother. The WO] analysis of the sulfide concentrate was nearly 1 pct for the Korean ore and about 0.1 pct for the Nevada ore. The tungsten contained in the sulfide concentrate constituted about 3 pct of the total tungsten in each ore. No effort was made to recover these tungsten values. The scheelite was floated with oleic acid. Adjustments in pH were made with sulfuric acid or sodium carbonate. A 1 pct solution of 85 pct Aerosol OT was sprayed on the froth and sides of the cell during the scheelite float to aid in dispersing the minerals and to decrease the entrapment of gangue particles. Six tests were planned for each of the six types of silicate in which concentrations of 1, 2, and 4 1b of silicate per ton of dry ore were investigated at both 6.5 and 10 pH. All tests were made at room temperature. The performance of each silicate was judged from the grade and recovery of WO, in the scheelite rougher concentrate. Tungsten recovery was calculated on the basis of the scheelite remaining in the ore after the preliminary sulfide float. Testing of each silicate at three levels of concentration and two levels of pH required 36 tests with each scheelite ore. Variance analyses were performed on the concentrate grades and recoveries to determine whether or not the type of sodium silicate, the concentration of sodium silicate, or the pH significantly affected recovery or grade. Results Concentrate Grade: A variance analysis of the concentrate grades for the Korean ore showed that concentration of the silicate and pH of the ore pulp were major factors in producing a high grade concentrate. Also, the silica- to-so da ratio was important as an interaction with pH. The concentrate grade vs silica-to-soda ratio is plotted in Fig. 1. The curves show that the concentrate grade improved with an increase in concentration of sodium silicate and also

Jan 1, 1959

By E. H. Crabtree

The heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. I, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. I, 1946, to represent the ferrosilicon medium. During the first of these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. Flowsheet The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through I½- in. and wet-screening out the minus 3/16-in. portion. The minus 136 plus 3/16-in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. Heavy-media Plant The heavy-media cone plant treating the minus I½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig I.

Jan 1, 1949

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,&apos; but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By H. M. Warren, E. J. Powell, A. S. Biesecker

In the past, steam engines were used in practically all cases for driving the machinery in and about an anthracite breaker, and hence few or no accurate data were available as to the power requirements for starting and operating the individual machines, which make up the complete equipment. It was impossible to segregate the power necessary to drive each individual machine, first, because the equipment was driven in groups, and second, because it was impracticable to obtain graphic, integrated, or instantaneous records of the horsepower used. As a result of these conditions, it was found, when individual electric motors were applied to the various machines, that more accurate and complete data were needed in order to provide motors of the proper power and design for the particular services to be rendered. In order to obtain the desired information, the writers made and collected a number of tests, from time to time, on the individual motor drives in electrically operated breakers, and as these tests have been of great value, it occurred to them that a paper giving the results might be of service to other engineers interested in similar installations. Table I shows the results of these tests. All the motors tested were of the three-phase, 60-cycle, 440-volt, induction, squirrel-cage type, except a few, which, on account of size and starting conditions, were of the wound-rotor type. The instruments used in making these tests were: An integrating watt-hour meter, a graphic ammeter, and a graphic voltmeter. These instruments were connected in each motor circuit, and a record of a day&apos;s run of 9 hours was obtained from each machine. From these tests, the running light load, the average all-day load, and the instantaneous peak readings in amperes, volts, and kilowatt input, were obtained. By means of the characteristic curves obtained from these motors at the factory, the power factor, the efficiency, and the horsepower output were calculated for each particular test. Starting tests were made by the brake-arm method, in which the torque in pounds was measured directly on a spring balance.

Jan 1, 1916

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat&apos;s depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"&apos;. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By Oliver B. Knight

The producing formation in the South Field, or "Golden Lane" structure of Mexico, is a buried ridge of reef limestone of Comanchean age overlain unconformably with sediments of Upper Cretaceous, Eocene and Oligocene. The structure extends in a long sweeping arc, with the convex side toward the west, from San Geronimo, Vera Cruz, to San Isidro, south of the Tuxpam River, which it crosses at the town of Alamo. It is 52 miles long and averages 3/4 mile in width. The surface of the producing formation of El Abra limestone consists of a series of minor parallel highs which are separated longitudinally by synclinal troughs and laterally by structural saddles. The presence of these highs has been of utmost importance in the development of the field, especially in recent years when the salt-water level has risen above the synclines and confined the oil to the isolated highs. In many cases, faulty information and interpretation of the subsurface has resulted in drilling costly dry holes and salt-water wells. Development The development of the Golden Lane was started by the Mexican Eagle Oil Co. in 1906. San Diego No. 3, usually known as Dos Bocas, the first producing well on the structure, was completed on July 4, 1908. This well came in unexpectedly for an estimated daily production of 129,000 bbl., and, as the casing was not properly set, the well flowed wild into the Tamiahua Lagoon, causing a loss of several million barrels of oil. In flowing wild the well formed a crater which covers an area of 48 acres, out of which salt water and small quantities of gas still flow. Casiano No. 2, the Huasteca Petroleum Co., which yielded 200 bbl. of oil daily, and which was completed in November, 1909, was the next producing well to be drilled on the structure. In 1910, the same company completed Casiano No. 7, with an initial production of 50,000 bbl. daily, and Casiano No. 1, which produced 200 bbl. daily. In the same year, the Mexican Eagle Oil Co. completed its Potrero del Llano wells 1, 2 and 4, with initial productions of 500, 400 and 100,000 bbl. respectively. From 3910 to the latter part of 1919, development proceeded

Jan 1, 1931

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.&apos; The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak&apos;s6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received &apos;acid-drainage&apos; contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.&apos; Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650&apos; to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By A P. Wibowo

Indonesia holds a significant role in the utilisation of coal resources in the world. Although the number of Indonesian coal resources and reserves do not fall into the world’s top ten, according to 2009 statistics, Indonesia is the seventh largest producer of coal with a production of 256 Mt. More than 80 per cent of this amount is sold in the export market, making Indonesia the world’s second largest coal exporter. Most of the exported coal from Indonesia is used to fulfil the needs of the Pacific market, such as Japan, Taiwan, China, among others. It is also possible to reach the Atlantic market.Along with Indonesia’s development program, until 2025 the Indonesian government has adopted a National Energy Policy that aims to reduce the role of petroleum in electricity generation and replacing it with coal. As a follow-up of the policy, since 2009 PT PLN, the state electricity company has built steam power plants throughout Indonesia as an implementation of the first stage of the Electrical Acceleration Project with a capacity of 10 000 MW. Moving forward, in 2011 PT PLN will also build the second stage of the project with a capacity of 10 000 MW. As a result of the program, the domestic need for coal is expected to increase as much as 44.8 Mt.With the increase in domestic need and decrease in the number of reserves, the Indonesian government has adopted policies to secure the domestic coal supply. A policy that may potentially be adopted by the government is the limiting of coal production, seeing the high rate of increase in Indonesian coal production. The adoption of such a policy will change the distribution map of coal in the Pacific market. Thus, this paper will evaluate the change of coal distribution patterns in the Pacific market along with the increase in Indonesian domestic needs and Indonesian adoption of policies regarding the securing of coal supplies.

Nov 22, 2011

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

"The first record of a kimberlite found in Canada (1946) was the identification of thin dykes intersected while drilling for gold in Michaud Township, Ontario.Sampling of the Munro Esker (1964) in the Kirkland Lake area, Ontario, by the Geological Survey of Canada identified the occurrence of detrital grains of pyrope garnets along a length of 35 km of the 113 km tested. A search for the source of the garnets resulted in the identification (1968) of a narrow subsurface kimberlite dyke in the Upper Canada Mine. This discovery resulted in a staking rush. Unfortunately, subsequent work did not identify the source of the kimberlite indicator minerals.During 1978 the Ontario Geological Survey started a multi-discipline study of 29 townships (2560 krn2) in the Kirkland Lake area, to encourage exploration for gold, base metals, and kimberlites. Back-hoe sampling (1979 to 1982), where the overburden was thin, and reverse circulation drilling, in areas of thicker drift, yielded samples of the till. These were analyzed for several elements and a mineralogical identification of the heavy minerals was completed. Pyrope and chrome diopside grains were identified.Studies of the Pleistocene geology indicated only the most recent direction (167 degrees) of ice advance (Matheson) and the associated deposits, out of a possible three advances known to occur in the general region straddling the Ontario-Quebec boundary, is present in the immediate area of Kirkland Lake. Contouring the distribution of pyrope grains (1990) showed a concentration centered over an area of 616 km2 extending down-ice from Gauthier Township. This included a smaller area containing chrome diopside grains. Kimberlite boulders were identified (1981) in gravel pits on the Munro and Misema River Eskers located within this anomalous area. The next step would be to use the airborne geophysical data to locate the kimberlite pipes which yielded the indicator minerals and boulders. The source area is likely to be in the northern half of the Ontario Geological Survey study area."

Jan 1, 1992

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.&apos; These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties&apos;3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969