Search Documents

By Roland Loewen

A review of the aqua regia method for the recovery of gold from jewelry shop wastes is given. Also outlined is a specialized procedure for the recovery of the silver that occurs in these wastes. A classic method for the recovery of platinum and palladium is, given. There is a brief review of other gold and silver refining methods. Environmental conditions are discussed and a few perhaps, new and useful processes ,are mentioned. References are by author or editor and are listed alphabetically. Suggestions for further information in the field of precious metals, are given in a final list.

Jan 1, 1989

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By B. Mishra, W. A. Averill

"The application of various hydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, ego metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been investigated and suggested for dealing with some of these wastes and scrap material.The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EM] and decontamination and decommissioning [D&D].IntroductionThe high temperature carbothermic or metallothermic smelting reduction methods for metal production are associated with the generation of significant quantity of waste as slags, flue dusts, sludges, residues, effluent salts etc. Certain hydrometallurgical processes also generate lots of aqueous waste due to the inherent nature of the technique. Also, the gas-based reduction processes are not applicable to many stable metal compounds, such as alumina, titania, beryllia, lanthanide and actinide oxides, etc. due to thermodynamic considerations. All these methods cause substantial environmental hazard. There is a need to develop alternative processes which have low waste or ideally a ""zero-waste"" generation.Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore (aluminum, beryllium, neodymium, plutonium, uranium, etc.) or from other process effluent that contain reactive metal compounds. The processes reduce metal compounds electrolytically (A12O 3 and BeCI2) on a carbon anode or by calciothermic reduction (Po, Nd). The by-product, in the latter case, is a calcium oxide saturated halide salt. The waste-treatment to recycle the halide has to be done as a separate step or stored as a contaminated waste. A successful separation technology can provide a new insight to the waste minimization strategy for the nuclear industry."

Jan 1, 1996

By Anton Gronningsater

AT the present time we hear a great deal about organization of labour, collective bargaining, workmen's councils, and company unions; about C.1.0. with its principle of vertical unions and A.F.L., largely based on craft unions; and about provincial and federal laws for protection of labour's right to collective bargaining. What we perhaps hear too little about is corresponding organization of the employers, although it recently is mentioned more frequently. I will only mention W. H. Davis, Chairman of the United States War Labour Board, who has had and is having plenty of experience in this field and has also studied labour conditions in Europe-in Sweden for instance. He has repeatedly expressed the opinion that where employer-employee problems are involved, a thing badly needed in America is organization of employers as well as employees to get some order in the present chaos. With this I agree. I believe a strong organization on one side necessitates a correspondingly strong organization on the other side; that has at least been the experience in the industrialized countries in Europe. I happen to be fairly familiar with conditions in Norway, where they have struggled with these problems for fifty years, and a talk on the history, development, and present state of employer-employee relations in that country might perhaps be of interest as giving a general picture of the development of such relations in the northwestern European countries as a whole. The talk was originally given to the Fourth Year students in Mining and Metallurgy at the University of Toronto. I have changed it somewhat to fit a different audience, but I hope you will make allowances if you now and then are reminded of the school auditorium. I will try to be as objective and factual as possible, but it is probably unavoidable that some of what is said is coloured by personal opinion.

Jan 1, 1943

By T. Doshi, S. Ennis

The interactions of mineralogy, chemistry and mechanics in an ore concentrator are highly complex, so it can be particularly hard to measure the impact of a specific plant change. This paper describes a method for modeling a baseline metal recovery so that the value of a major process improvement can be measured. This method only considers variables that cannot be optimized, such as mineralogy or equipment availability. Linear regression, random forests, extreme gradient boosting (XGB), and simple two-layer neural network models of process value were tested as candidate baseline model types to assess the impact on throughput and recovery in a copper concentrator. XGB performed the best in terms of accuracy for both throughput and recovery models. Using an XGB model of nonoptimizable process variables provides an accurate, dynamic baseline that can be compared with continuous production data to determine the value added by major concentrator improvements in real time.

Mar 2, 2022

By M. Javier

Management is a major part of sustainability research. Many different aspects of sustainability have already received significant research attention, but the management processes in mining from the perspective of their impact on society are less understood and integrated as a holistic frame. It is evident that mining technology has received major blame in past ecological disasters and major mining-induced environmental hazards, but the management-mining process has escaped unscathed. This should not have happened. Instead, the management processes should share equal blame with obsolete technology for the failure to identify and monitor potential environmental hazards before their inception of mining. We will present an emergent style of management for the future of mining. It challenges the actual ?mind-set? of mining management. It describes balance and equilibrium: physical, chemical, and biological in nature as an understanding of nature?s language, which is Geomimic along side ?the bottom line?. The goal is to minimize loss instead of maximize profits (waste design) at the design stage of mining and to develop clean technologies (nature's values) to achieve non-social environmental impacts that provide a prosperous legacy to future generations.

Jan 1, 2010

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

By A. Y. Smith, R. J. Allan, E. H. W. Hornbrook, R. W. Boyle, W. Dyck

"HYDROGEOCHEMICAL METHODS in the Canadian Shield can be based on analyses of the following :(1) spring waters and their precipitates;(2) stream and river waters;(3) lake and muskeg waters;( 4) ground waters from drill holes, wells, faults, etc.;(5) waters issuing from diamond drill holes, faults, shear zones, etc. into mine workings and open pits; also analyses of precipitates associated With these waters.The first four can be utilized in both reconnaissance and detailed surveys. The last is suitable only for detailed work.For hydrogeochemical methods of prospecting to be effective, the following conditions must be present. 1. Natural waters must come into contact with mineral deposits and remain in contact with them long enough for the solution of detectible amounts of ore, gangue or indicator elements. 2. Dispersion patterns must be present in the hydrologic systems in order to trace the elements back to their source. These patterns may take the form of trains (e.g., increasing amounts of elements upstream toward t he source (s), Figure 1 ) or halos (e.g., increasing amounts of elements in bodies of water toward the source (s), F igures 2 and 3)."

Jan 1, 1971

The selective placement of coal strip mine overburden is examined. Physical end chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions of similar problems. Five mining methods already used in the industry, that are capable of selectively handling; waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons arc made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided.

Jan 1, 1981

By John E. Roberts

People are not a novelty. But the phenomenal numbers thereof, who have approached, settled, and been born in California in the past twenty-five years, are such a problem as to be a novelty in the broadest sense of the word. California, with less than 7,000,000 people in 1940, and over 19,000,000 in 1966. In 5 1/2 years, (1960-65) the southerly 14 counties of California, which together comprise one-half the land area of our state, had an increase in population greater than Colorado, or Arkansas, or Oregon, or any one of 19 other states.

Jan 1, 1967

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By A. W. White

Introduction To discuss all the technical details of incorporation laws, security laws, underwriting procedures, codes, and ethics-as laid down by varous associations -would be impossible in the time which has been allotted to me. My remarks, therefore, will be made in a very general way and will naturally be coloured with experiences which my firm and I have had. There is a common expression that "money makes the mare go". I hardly have to mention here that the best prospect in the country is of very little value unless its prospects can be developed-and this requires large capital expenditures. The art and problems surrounding the raising of this money is a long and interesting story. Since by its very nature mining is risky, the appraising of its risks in the many phases of its development programme is continuous. Very few men-if any-and very few corporations -if any -can afford to take all the risk of mining. Because of taxation policies-and the very scheme of present-day living -the truth of this statement can be seen throughout the whole industry by a close examination of the records. Since this is so, it is essential that the mechanics of distributing risk on a sound, and equitable basis be known to those engaged in the business and to the investor or spectator who proposes to risk his funds in the industry. Perhaps the greatest stimulant to modern business activities has been the creation of corporate bodies. It is evident, from the number of charters being granted by various jurisdictions, that this method of doing business is becoming more and more important. A limited company -or corporation-can be defined as a fictitious person existing solely in contemplation of the law.

Jan 1, 1951

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By M. Springett

Organization of teams for rapid and effective evaluation of international mining properties requires special considerations beyond those needed for domestic activities. Experience, technical ability, a sense of perspective, humor and self-discipline are vital characteristics to look for in the selection of individuals for forming an efficient and productive team.

Jan 1, 1994

By D. C. Peck, James. R. S., Chubb. P. T.

"Abstract -The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered matie intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendritic­ pegmatitic matie pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and mag­ matie breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to lOOJo within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that af­ fected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd :Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Severa! factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic inter­ action with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion .The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Com­ plex, U.S.A.) in terrns of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economie concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginal­ type POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality over time. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By Joseph W. Richards

ALTHOUGH bad grammar, the above query is probably, at the present moment, good sense. Why was the Institute started and why does it continue to exist? The small group of men who worked out the original idea felt keenly the necessity of mining engineers and metallurgists getting together in order to discuss their professional problems. That necessity still exists but it does not strike the present generation of engineers so keenly because they have always had the Institute: they do not know what it is to be without it. The Institute is a great graduate school of mining and metallurgy. All of its members who have something to say worth saying are the teachers; all the rest may be learners or critics. No university or technical school can match the experience and information which the authors of its papers possess, no institution of learning has a body of potential listeners so extensive and so vitally interested.

Jan 1, 1921