Search Documents

By Noller B. N, McGill R. A

The Alligator Rivers Region has been the scene of one of Australia's most intensive environmental monitoring efforts since the current generation of uranium mining was mooted in the 1970s. Prior to mining, the local environment and the nature of potential impacts were not well known. The initial monitoring programs therefore included large baseline characterisation and research components. After some 15 years, water, soil and sediment monitoring programs have been reduced to a fraction of their early size, as the mining and natural systems became better known and characterised, and the actual nature of the environmental impacts were established. Modem techniques allow much more rapid and thorough identification of chemical species and elements of concern, allowing much more focused monitoring programs to be designed. In the 1980s data collection was emphasised at the expense of interpretation, and monitoring programs were maintained at much higher levels than were in fact required. It is now clear that investigations are important and should be distinguished from monitoring programs, and that the timely interpretation of investigations and implementation of recommendations can greatly reduce the effort and expense that can be involved in a monitoring program. Monitoring programs based on a sound understanding of potential environmental impact may then be efficient and cost-effective, yet provide sufficient information to assess the environmental impact of mining, guide further environmental protection measures when problems are detected, and demonstrate compliance with regulatory requirements.

Jan 1, 1994

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

By J. D. Lubahn

Prior tests by Dorn, where the strain rate in a tensile test was suddenly changed, have shown a small, but definite rate-history effect to exist. If this effect is neglected in the calculation of creep behavior from tensile results, an error should occur. This paper shows that this error is smaller than experimental scattering, and may be neglected. DORN1 has found a small but definite rate-history effect in the aluminum alloy 250 at liquid-nitrogen temperature using tensile tests with an abrupt rate change. Such an effect is to be expected from pre-viously known2-6 temperature-history effects, together with general experience that effects produced by changing the strain rate a large amount are simi-

Jan 1, 1959

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

By Ho-Sang Sohn

Copper concentrate particles of 200 to 300 mesh size were fed from the top of vertical reaction tube of 2.8 cm ID and 2 m long with an O2-N2 gas mixture. The reaction tube was heated to 900 K to 1100 K. The residence time of the particles in the reaction tube was about 1 second. The copper concentrate particles were very rapidly oxidized and melted down during their descent in the reaction tube. The particle temperature were calculated by combining an un-reacted core model, mass transfer between gas and particles, and heat transfer between gas, particles and tube wall. The particle temperature reached its maximum within a distance of 60 cm from the top of reaction tube, and it attained at 2000 K at higher oxygen partial pressure. The most particles were melted at the oxygen partial pressure above 20 kPa. An appreciable amount of As, Sb and Pb in the concentrate particles was eliminated in the upper portion of the reaction tube and the rate of elimination are explained by the rate of mass transfer of volatilized species through the gas film on the particle surface and the variation of particle temperature during the descent.

Jan 1, 2006

By P. K. Gbor

Over 2 million tonnes of smelter slags containing Co, Ni and Cu are produced and stockpiled in Canada each year. Smelters also produce SO2 an air pollutant. Recycling these materials will maximize the value of natural resources and minimize possible environmental impacts of industrial operations. The objectives of this research were to understand the characteristics of slag, the reaction of slag with SO2(aq) and to develop a novel method for extracting Co, Ni and Cu from slag using SO2. The properties of slags from different smelters were studied, with emphases on the form of Co, Ni, Cu and Fe. Leaching experiments were carried out in a batch reactor. The parameters investigated included concentration of SO2(aq), stirring speed, particle size, temperature and pH. O2 was introduced into the reactor to study its effect on the system. The amount of each of Co, Ni and Cu in all the slags was less than 1%, while Fe was between 30% and 45%. The form of Co and Fe was primarily oxide, however, significant portions of Ni and Cu were present as sulphides. SO2(aq) alone, was effective in leaching Co and Fe. Cu dissolution was negligible due to precipitation. The presence of O2 improved Cu and Ni extraction. SO2(aq) was found to be more effective in leaching slag than H2SO4 at the same pH. The leaching process was modelled using the shrinking core model. A scheme was proposed for the extraction of Co, Ni and Cu from slag using SO2(aq). The process makes efficient use of SO2, separates Co and Cu at an early stage, and minimizes the consumption of base during Fe separation.

Jan 1, 2003

By H. C. Doepken

Wrought Hadfield steel was tested in axial tension at from 100° to —196°C, to determine flow and fracture stresses as well as conventional properties. Ductility and related properties, such as fracture stress, decreased continuously with temperature. Peculiarities during straining indicated possible martensite formation or mechanical twinning. THE mechanical properties of austenitic manganese steel have been summarized by Avery and Day,' including the low temperature tensile properties reported by Hadfield and coworkers2,3 " These data show the material to be brittle at both liquid oxygen and liquid 'hydrogen temperatures. Avery and Day report considerable ductility measured by Charpy V-notch tests at —100°F (-73°C). Since the review of low temperature properties by Seigle and Brick' show face-centered cubic structures, other than Hadfield steel, to be ductile at low temperatures, it was felt that a study of tensile properties, between the reported intervals, should show whether the decrease in ductility was a gradual decline or an abrupt drop beginning at some intermediate point. X-ray examinations were made in an attempt to shed further light on the mechanism of work hardening of austenitic manganese steel. The presence of a magnetic constituent has been found by Hall" and by Avery, Homerberg, and Cook." Krivobok7 demonstrated the growth of magnetic constituents on reheating cold-worked specimens. Hadfield2,3 ' and Goss found no a iron. The steel from which the specimens were taken was commercial hot rolled % in. diam rod of electric furnace steel. The ladle analysis was as follows: C, 1.40 pct: Mn, 12.11; P, 0.060; S, 0.012; Si, 0.120; Ni, 0.080; and Cr, 0.090. Fifteen specimens, 6 in. long, were cut from a

Jan 1, 1953

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005

By A. M. L. Cushing, S. Kelebek, A. Ghahreman

Iron sulfides are part of many ore deposits affecting flotation separation of non-ferrous base metals from them. Open-circuit potential (OCP), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements were carried out with pyrite and pyrrhotite electrodes to investigate their reactivity under various flotation conditions, which involved the use of TETA, SMBS, and their combination. TETA was found to adsorb on the electrode surfaces causing a significant increase in charge transfer resistance of the product formed, which was most significant at OCP. This effect is much less with SMBS, indicating its greater surface reactivity compared to TETA. The combined use of these reagents decreases charge transfer resistance to a greater degree than that experienced with their individual uses. Addition of Cu2+ as a potential activator to this system nearly eliminates the action of TETA on the electrode surface, which can be attributed to sequestration/chelate formation in liquid phase. The relative effects of these reagents on pyrrhotite electrode are similar to that of pyrite. The main difference between the pyrite and pyrrhotite electrodes is that the observed charge transfer resistance on the pyrrhotite surface with each reagent case is significantly lower by 3 to 4 fold. This is compatible with its anodic nature and ease of oxidation since the OCP value of pyrrhotite is lower than that of pyrite. Results are discussed in relation to flotation/depression behavior of these iron sulfide minerals in mineral separation processes.

Jan 1, 2017

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

By Ron J. Elliott, David G. Otto

This project involved deep blast densification of recent volcanic avalanche debris deposits consisting of a 43 meter thickness of loose clean to slightly silty sand, gravel, cobbles and boulders deposited as a result of the 1980 eruption of Mt. St. Helens, Washington, U.S.A. This project was carried out to enhance the resistance to liquefaction or dynamic settlement of soil deposits under the bridge abutments for construction of the 59.4 meter long South Coldwater Creek Bridge. As this bridge is located close to the Mt. St. Helens fault, it will in all likelihood be subject to earthquakes in the order of 6.5 with expected accelerations of 0.55g. Without soil densification, the bridge would suffer severe structural damage in the event of a significant earthquake.

Jan 1, 1994

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.' It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By I. Grigoriev, A. Yolkin, E. Freiberg, A. Fedchun, A. Kolichko

Abstract: The paper describes the engineering-geological conditions and the structural decisions of the underground machine hall of Rogun HPP under construction in Tadjikistan on Vaksh river as well as the results of physical model studies and long-term in-situ investigations of the variation of the stress-strain state of the surrounding rock mass and the supports of openings, and the assessment of the stability of openings during and after the construction. The analysis of the results of long-term in-situ observations and previous model studies permitted to make the assessment of the present-day state of the machine hall and give recommendations of its further use. Zusammenfassung: Im Vortrag werden die ingenieurgeologischen Bedingungen und konstruktiven Lösungen für die unterirdischen Maschinenhalle des in der Republik Tadshikistan am Fluss Wachsch im Bau stehenden Rogunskaja-Wasserkraftwerkes, die Ergebnisse von experimentellen Forschungen (in physikalischen Modellen) und Naturbeobachtungen der Spannungs-Verformungszustandsänderungen des umliegenden Felsmassivs und Ausbaues von Untertagebauten, sowie Ergebnisse der Bewertung der Standfestigkeit von Untertagebauten während des Bauvorganges und nach der Bauperiode beschrieben. Auf Grund der Analyse von Ergebnissen der dauernden Naturbeobachtungen und früher durchgeführten geomechanischen Modellversuche wird der heutige Zustand der Maschinenhalle des Wasserkraftwerkes bestimmt und werden die Empfehlungen für ihren weiteren Benutzung angeführt. Annotation: L’exposé décrit les conditions d’ingénieur et celles géologiques, et les solutions constructives de la salle des machines de la Centrale hydroélectrique (CHE) Rogounskaya sur le fleuve Vakhch, les résultats d’études expérimentales (sur des modèles physiques) et d’observations extérieures sur place concernant des changements de l’état de tension-déformation d’un massif environnant et du cuvelage des excavations, ainsi que les résultats d’évaluation de la stabilité de l’excavation au cours de la construction et à la période post-construction. A la base de l’analyse des résultats des observations de longue durée et des études préalables géomécaniques sur des modèles, l’évaluation de l’état actuel de la salle des machines de la CHE est effectueé, et les recommandations sur son utilisation ultérieure sont présentées.

Jan 1, 2003

By B. Samanta

Abstract - Ore reserve estimation, based on sparse drill hole data, was conducted for a placer gold property in Nome, Alaska. A problem with sparse data is that random subdivision of the data into modelling and evaluation subsets (as is commonly done) becomes a problem, as random selection may result in biased/skewed subsets. Therefore, a technique that combined data segmentation with genetic algorithms (GA) was applied to divide the samples into three equivalent subsets: training, validation and testing. Data segmentation was done on the basis of the distribution of gold values. Neural network and a variety of kriging techniques were used to estimate gold grades. A multi-layer feed forward neural network along with "early/quick stop" training was used for neural network modelling. A comparative evaluation of kriging and neural network methods was then performed. The results revealed that neural network was generally superior to the kriging techniques for gold grade estimation in the Nome deposit.

Jan 1, 2002