Search Documents

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

By Jeffrey M. Listak

The Respiratory Hazards Control Branch of NIOSH routinely conducts laboratory and mine-site evaluations of dust control technologies. Gravimetric and instantaneous dust sampling instruments are used in these evaluations to measure and document dust levels to determine worker exposure. The Thermo personal DataRam (pDR) is an instantaneous sampler that uses light-scattering technology to provide relative measures of airborne respirable dust. The pDR can be used in active and passive modes to measure respirable dust levels. Tests were conducted to evaluate the sampling performance of active and passive pDR operation relative to each other and. against a gravimetric sampler (the accepted standard for respirable dust measurement). The purpose of the test was to determine if the pDR can be used effectively in the passive mode in higher velocity airflows (up to 5.1 m/s (1000 fpm)). Studies of the pDRs in both modes of operation were conducted in a controlled laboratory environment and in field situations. Dust measurements using pDR units in both modes of operation were recorded in ve¬locities ranging from 1.0 to 5.1 m/s (200 to 1000 fpm). Tests were conducted in ambi¬ent air and in air with the addition of moisture. Results show that, although the units measure different concentrations in their respective modes of operation as compared to a gravimetric sample, the relative readings can be corrected to yield accurate dust measurements.

Jan 1, 2007

By L. W. Strock

Metallurgists handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. 'lore preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The howledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Expcrience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,' but the incentive has gradually changed since the summer 0. 1940 to the specific practical problem of searching for domestic sources of rare and stratcgic metals. The

Jan 1, 1949

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By Edgar Dunn

PART I.-DETERMINATION OF GASES IN SMELTER FLUES. IN 1907, upon arriving in Anaconda to take up work in the testing department of the Washoe Reduction Works, the. following problem was met at the car step, so to speak: complete and. exact analysis of gases, not only at the stack, but also in all departmental flues. Taken up to employ time not otherwise needed for regular testing department work, instructions were extremely liberal for a commercial plant, to the effect that accuracy should not be sacrificed to speed. In December, 1907, the work was temporarily transferred to the Great Falls Smelter, and some of the methods here given were there worked out. Differences in smelting operations at Great Falls and Anaconda, however, necessitated further investigations and the development of a new method for S03 determinations at the latter plant, where work was resumed in July, 1908, and completed about a year later. At the time of inception of the work, data (not only on percentages, but even on methods) were found to be meager in the extreme, for one or the other of two reasons: either entire lack of experiment at a large proportion of smelters, or disinclination on the part of the managements to divulge data of any description pertaining to either results or methods. In making determinations of gaseous constituents of flues, two methods are open to consideration: 1, the drawing out of a sample, and collection of the same as a whole, to be removed to the laboratory for later analysis; and 2, the absorption in situ on the flue of one certain constituent, disregarding others for the time being, or perhaps combining two or three in one determination. The first is generally the more rapid, but it is also the more inaccurate, method of analysis, even with special type absorption apparatus, being the more largely subject to error, both of reading, and also because of leakage during complicated manipulation in the laboratory. The amount used for analysis must also, because of limit of container, be small for the first method, and an average gas is very seldom obtained, necessitating for a fair average result a large number of determinations. Consequently, when we balance the time spent in a dozen determinations of short-time samples as against the time employed in making two or three long-time determinations of various constituents in situ, we are not so certain in our statement as to the relative speed of the two methods. Moreover, the method of analysis in the laboratory of 100 cc. of flue gas is satisfactory only when constituents thus determined are present in considerable quantity, results being simply approximate when determining such compounds as sulphur dioxide, sulphur trioxide, carbon monoxide and dioxide, and arsenic trioxide and water vapor, none of which are carried in all smelter flues in amounts in excess of (or even approaching) 1 per cent by volume. Special condi-

Jan 8, 1913

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, .as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

John J. Porter, Cincinnati, Ohio (communication to the Secretary *):—The remarks of Mr. Firmstone concerning the presence of nickel in Oriskany ores, call to my mind some additional evidence on this point. In 1903, while engaged in the determination of zinc in a number of samples of ore from the Oriskany mine of the Alleghany Ore & Iron Co., I was surprised to discover the presence of nickel and cobalt. As far as I was then able to discover, their present;! had up to this time remained unnoticed. The amounts ranged from 0.05 up to 0.10 per cent. of the combined oxides, and while no attempt was made to separate the metals, the presence of both nickel and cobalt was conclusively proven. Since that time I have learned that traces of these metals are of quite general occurrence in Virginia iron-ores, and more especially in the ores of the Potsdam formation from the western slopes of the Blue Ridge. In certain manganese-ores from this formation, I have found as high as 0.50 per cent. of nickel and cobalt oxides. Any one interested in this subject will find further information in a volume l written by Andrew 8. McCreath, and printed in 1884 for distribution by the Norfolk & Western railway. A number of complete and accurate analyses of Virginia iron-and manganese-ores are given, and practically all show nickel and cobalt in appreciable quantity. Still another source of information on the occurrence of nickel in iron-ores in the United States, for which I am indebted to Charles Catlett, is found in the Tenth Census. Several analyses of Oriskany ores are given: all of which show the presence of nickel, with less cobalt, while the single representative from the Potsdam formation shows nickel, with no cobalt.

Jan 1, 1909

By V Sanmartfn, J Torracchi

The broad biodiversity of our country is manifested through several different biological forms. From the villages of Portovelo and San Gerardo in the southern part of Ecuador, some samples of water and rocks were taken in order to identify the native micro-organisms which take part in the natural processes of leaching of sulfurous minerals. The presence of Spp Thiobacillus ferrooxidans was determined together with a fungi sample which has not yet been characterised by the current workers. These have been isolated, grown, experimented and conserved in appropriate cryogenic environments. The present research intends to study the individual and group adaptation of the bacteria and the fungi upon suitable systems of agitation and ventilation, in combination with several different concentrations of refractory auriferous samples. These refractory samples were derived from old mine workings and the experiments were performed to test the effectiveness of the isolated species in bioleaching as pre-treatments upon the cyaniding processes. The capability of these bacteria to develop in environments with high concentrations of cyanide has also been studied, to investigate the possible use of bacteria in the biodegradation of cyanide. The presence of Thiobacillus ferrooxidans in acid conditions has already been tested in advance, however, the presence of fungi species in these conditions are studied to prove their efficiency as another alternative for the bioleaching of refractory auriferous minerals and Baptista, 1998).

Jan 1, 2004

By M. H. Merriss

In the last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, &apos;Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes&apos; that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.&apos;s plant. At Baltimore, the anode is rolled to perfect

Jan 1, 1926

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By J P. Hsi

Recent increase in the development of underground space in urban areas in Australia has included soft ground tunnel construction. The ground movements associated with soft ground tunnel construction may present risk to other existing and proposed structures in the nearby vicinity. Much experience has been gained both in the UK and Asia in recent years in the engineering evaluation of this risk. The paper presents a procedure to assess these aspects of soft ground tunnel construction with reference to recent projects.

Jan 1, 1999

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

By V. D. Tathavadkar

Natural chromite mineral is a solid solution of spinet end members namely: chromite (FeCr2O4), hercynite (FeA1204), magnetite (Fe3O4), magnesio-chromite (MgCr2O4), (MgA12O4), and magnesio-ferrite (MgFe2O4). A phase transformation in chromite minerals occurs in oxidising conditions during the soda-ash roasting reaction. This phase transformation plays an important role in improving the extraction efficiency of Cr3+ from mineral phase. The extraction efficiency of chromium (Cr3+) from chromite to a water¬soluble sodium chromate (Cr6+) salt depends upon the decomposition kinetics of the spinet phase. An investigation of the phase changes in chromite ores in the absence of sodium carbonate was carried out in air, argon, and in argon +5 % hydrogen gas mixture. The thermodynamics of phase transformation reaction in chromite solid solution phase is discussed using the solution model proposed by Sack and Ghiorso [1]. The microstructural changes and the changes in elemental compositions of different phases were examined by SEM and electron probe microanalysis (EPMA) respectively. The experimental results indicate that the solid solution spinet phase in chromite mineral undergoes spinodal decomposition under the influence of oxygen partial pressure and temperatures. The structure of phases formed and their morphologies suggest that the phase decomposition may be similar to those observed by Burkert et. a]. 121, although the scale of phase separation in chromite appears to be strongly dependent on oxygen partial pressure.

Jan 1, 2001

By J. Dubinski

Passive tomographic imaging is a technique that can be used for assessing seismic hazard in mines with high seismic activity induced by mining. The basic idea behind such an interpretation is the assumption that there is a relationship between high values of seismic velocity and high values of stresses in the rock mass. This relationship was confirmed both in laboratory an in situ measurements and constitutes the basis for rock-burst and seismic hazard evaluation. In the paper seismic tomographic images of seismic P wave velocity and seismic P wave velocity gradient have been presented to determine rock-burst hazard and locate high seismic activity zones in the area of coal panel 306 in Zabrze Bielszowice mine. The zones of high values of P-wave seismic velocity gradient have been found to correlate with the distribution of high energetic seismic events. Passive tomographic images were obtained using modern bent ray tracing tomography algorithm with regularization. Recent study give rise to observation that not only high values of P-wave seismic velocity is important in seismic hazard assessment as many strong seismic events are located in the areas of high values of velocity gradient. This recent observation permits to increase quality of passive tomographic imaging for detection of seismogenic zones and is presented in the paper. The advantage of passive tomography comparing to active tomography is that sources of seismic waves are generated by rock mass itself and costly controlled explosions are not necessary. Another practical limitation of active tomography is the size of study area which usually do not exceed 200 m by 200 m. This restriction does not appear in passive tomography where area of study is usually 2000 m by 2000 m and the tomographic images delineate velocity structure in locations where mining induced seismicity take place. Passive tomography method utilized in analysis of rock mass state in underground mines encounter some difficulties concerned with the numerical stability of optimization algorithms. In the presented approach to passive tomography problem numerical stability is obtained by special regularization method and by application of very stable numerical seismic ray-tracing algorithm.

Aug 1, 2013

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By P. A. Beck, L. J. Demer

As reported in a previous publication,&apos; isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

By H. H. Podgurski, F. N. Davis

In silver alloys containing less than 0.2 wt pet Cu. the reaction 9 + 1/2 0, = CuO(s) was found to proceed to equilibrium between 700o and 808oC. From measurements of the equilibrium dissociation pressures of the CuO at several temperatures, the differential heat of solution and the activity coeflicients for copper in silver were calculated. These values were found to be in reasonable agreement with those calculated from data appearing in the literature. A metastable "copper oxide" with an atom ratio of oxygen to copper as high as 1.7 was formed by internal oxidation at 300°C of these same dilute Ag-Cu alloys. No anomalous behavior was noted in the temperature dependence of oxygen solubility in silver. The solubility minima between 300" and 800°C reported several years ago can be accounted for, at least in part, by reactions with trace impurities, such as copper. Cold-worked siloer exhibits an enhanced permeability to oxygen. THIS investigation was undertaken because of our interest in interactions between solute and lattice defects in metals. The reason for the choice of the O-Ag system for study is the anomaly in the solubility of oxygen in silver reported by Steacie and Johnson1 in 1926, specifically that isobars between 100 and 800 Torr show solubility minima at 400°C. It was also claimed that the copper impurity in the silver was not responsible for the minima. Recently, Eichenauer and Müller2 proposed that surface adsorption might have been responsible for this solubility anomaly, but no adsorption isotherms are available to check the pressure and temperature dependence observed at the low temperatures. Surface-tension measurements on silver made by Buttner, Funk, and udin3 suggest that a considerable fraction of a monolayer of oxygen exists on silver at 922°C and at an oxygen pressure of 150 Torr. To account for the pressure sensitivity reported by Steacie and Johnson1 at 300°C, the oxygen bound to the surface at 922°C cannot be considered relevant; the existence of a surface layer at 300°C characterized by a lower energy of binding would be required to explain the effect. All of our attempts to detect an interaction of this type with surface sites have failed. In this investigation we have not been able to associate the dissolution of oxygen in silver with a dislocation interaction. Evidently, severely cold-worked silver does not contain a sufficient number of trapping -sites for oxygen. Indeed, our work shows that oxidation of trace impurities in the silver was probably responsible for Steacie and Johnson&apos;s results. In addition, we have been able to establish the nature of the reaction with copper impurity in silver by thermodynamic considerations. EXPERIMENTAL PROCEDURE Measurements of both the internal oxidation rates and the solubility were made volumetric ally in a system equipped with a gas burette, a mercury manometer, a McLeod Gage, and a mass spectrometer. The silver and the silver-alloy samples were protected from contamination by mercury vapor from our pressure gages by suitably placed refrigerated (-78°C) traps. Silica reaction vessels were employed for experiments performed above 500°C. Spectroscopically pure gases were used in this investigation. The highest-purity silver used in the solubility measurements was 99.999 pet. By chemical analysis 2 ppm of Cu were found in this silver. The two Ag-Cu alloys used in this research were made up to 0.14 and 0.15 wt pet Cu starting with 99.999 pet Ag. An unexpected source of error was discovered in the course of the work. At temperatures near 800°C silver distilled from the hot silica reaction tubes into cooler regions of our system. Although the weight loss of silver from the sample was not important in itself, oxygen was being consumed by the silver distilled into the cooler part of the system to form a stable oxide phase from which the oxygen was not recovered. In a separate experiment conducted to determine the necessary correction, losses between 0.2 and 0.3 cu cm (stp) of 0, in 24 hr were measured at 810°C. On the assumption that the flux of silver from the vessel to form Ag2O de-

Jan 1, 1964

By G. L. Fisher, R. H. Geils

The effect of small amounts of columbium (<0.01 to 0.10 pct) on the ?-a transformation occurring during the continuous cooling of a low carbon Ni-Cu steel was investigated. Dilatometer specimens were aus-tenitized at 950" and 1068?C and cooled at 17? and 375 C° per min. Columbium caused a marked depression in the ?-a transformation temperature except when cooling at the slower rate from 950°C. The effec of columbium on the transformation temperature was greater the higher the austenitizing temperature and rate of cooling. A maximum depression of 92 C" was observed. Metallographic examination of specimens of <0.01 and 0.07pct Cb steels heated at 1200°C for 1 hr and cooled at various rates showed that columbium had a major effect on the ferrite morphology. The fer rite in the columbium -free steel remained equiaxed at cooling rates as high as 440 C? per min while the columbium-bearing steel exhibited mixed structures o equiaxed and bainitic ferrite at cooling rates as low as 130 C° per min. The ? grain boundaries in the columbium -free steel provided the ferrite nucleation sites in rapidly cooled specimens. There was a complete absence of nucleation at these sites in the colum bium-bearing steel. It is concluded that columbium depresses the transformation temperature by suppressing ferrite nucleation at the austenite grain bound-aries. In this respect the effects of columbium are analogous to those of boron in low C-Mo steels. It is well known that small columbium additions can substantially strengthen plain carbon steels. As little as 0.02 pct Cb can increase the yield strength of mild steels by 10,000 psi.1 A fine precipitate of CbC has been observed in columbium-bearing steels2 and is generally thought to be responsible for the strengthening. Little attention has been devoted to the effect of columbium on the ?-a transformation. Webster and woodhead3 have studied the effect of columbium on the isothermal proeutectoid ferrite reaction in mild steels. They found similar transformation behavior in steels both with and without columbium additions. However, as the austenitizing temperature increased, the incubation time for the start of the ferrite transformation became longer in the columbium-containing steel. Morrison1 found that the addition of 0.03 pct Cb to a C-Mn steel lowered the transformation temperature by 50 C° during cooling from 1200°C at a rate of 80 C" per min. The strengthening effect of columbium has recently been utilized in an age-hardenable, low-alloy steel containing copper and nickel.4 A small amount of columbium has a substantial effect on the as-rolled strength of this steel. By increasing the columbium level from <0.01 to 0.13 pct the as-rolled yield strength is increased by 15,000 psi. Columbium also significantly lowers the ?-to-a transformation temperature of this steel during continuous cooling from the austenitizing temperature. Because of the low carbon level in this steel (0.05 pct max), it is almost entirely ferritic. Thus, it offers the opportunity of studying the effect of small columbium additions on the proeutectoid ferrite reaction. Of particular interest in this study was the reason for the marked lowering of the transformation temperature by columbium during continuous cooling. EXPERIMENTAL PROCEDURE Materials. The compositions of the steels used in this investigation are shown in Table I. The steels were 30-lb air induction melts. They were forged to 4 by 8 by 1 in. plate at 1230°C, air cooled, and then reheated to 1230°C and cross-rolled in two passes to in. plates. Dilatometry. A Leitz Bollenrath dilatometer was used to record the transformation during continuous cooling from two different austenitizing temperatures. The dilatometer specimens were + in. in diam and 2 in. long. Oxidation and decarburization of the specimens was prevented by maintaining a small positive pressure of dry argon in the dilatometer furnace and by plating the specimens with 1 mil of Cu. For the lowest cooling rate, 17 C" per min, the temperature of the specimen was measured with a Pt-Pt 10 pct Rh thermocouple placed in a & in. diam well in the center of the specimen. During air cooling, 375 C° per min, this method of measuring the temperature interfered with the operation of the dilatometer. However, it was found that the temperature of the specimen could be measured accurately by placing a thermocouple in an identical specimen in a holder adjacent to the one being used to operate the dilatometer mechanism. The dilation-temperature curves were recorded on photographic film and then converted to volume percent ferrite-vs-temper-ature curves. The cooling rates obtained with the dilatometer are shown in Table 11. Cooling rates of

Jan 1, 1970

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,&apos;-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer&apos; indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964