Search Documents

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612' F. (322' C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By M. van Elp, R. Saitua Nistal, P. J. M. Groot

Demand for construction raw materials depends on investment in housing, other buildings and infrastructure. The provision of these materials requires early knowledge of future trends in construction investment. By using scenarios possible future developments and bandwidths can be explored. Policy makers in government organisations as well as in the private sector can base their policy decisions upon these insights. In this paper we discuss the case of sand and gravel in the Netherlands. We will show that, depending on the future role of government and the degree of internationalisation, the long term demand for construction raw materials will strongly diverge. Nevertheless there are some common developments such as a decreasing population growth, a smaller share of the labour force in total population and a growing wealth. In different scenarios we will encounter different conditions for minerals provision and for sustainable development.

Jan 1, 2011

By R. F. Steigerwald

The effects of heat transfer on the corrosion behavior of type 304 stainless steel in boiling water have been studied. Heat transfer conditions increase the tendencies of the stainless steel toward stress-corrosion mucking when the water is contaminated with Cl-. Surface preparation is the most important variable in determining the severity of the stress-corrosion problem in water with a given Cl- content. Heat treatment, chemical cleaning, and degree of wet film boiling also affect the corrosion of stainless steels used as heat transfer surfaces in boiling water. An up-paratus for corrosion testing under controlled heat transfer conditions is described. THE principal objective of this investigation was to study the corrosion behavior of AISI Type 304 stainless steel in boiling high-purity water under conditions of heat transfer. The principal variables in the study were: a) boiling conditions: limited boil, agitated boil; b) metallurgical structure: annealed or sensitized; c) surface condition: rolled, pickled, or ground. The results of the study should elucidate the role of heat transfer in the corrosion of stainless steel in boiling high-purity water and provide a base line from which to assess the severity of this type of corrosion. Although there has been an investigation of the effect of heat transfer on the corrosion behavior of stainless steels in alkaline waters,' work on the corrosion of stainless steels under heat transfer has been largely confined to various acid solutions.'-4 Furthermore, the study of the corrosion of stainless steels in high-purity water has been generally restricted to auto-clave and instream testing in superheated (e.g., 300°C) water and steam.5'6 Cooling water problems led to this study of the corrosion behavior of type 304 stainless steel in high-purity water at its atmospheric boiling point. In addition to the effects of heat transfer, this study also considered the influences of the type of boiling,7 metallurgical structure, and surface condition on the corrosion behavior of stainless steel in high-purity water. Two boiling conditions were investigated in this study: a) limiting boiling, i.e., when the heat-transfer surface had just reached the boiling point and boiling nucleated randomly over the specimen surface and b) agitated boiling, i.e., when a mild degree of superheat had been achieved on the specimen surface and boiling occurred generally over the specimen surface. Both boiling conditions are broadly classified as wet-film boiling. Originally, this program included the study of a third type of boiling, dry-film conditions. At dry-film boiling the temperature of the heat transfer surface is high enough so that it is covered with a continuous film of steam. Experimental difficulties made it impossible to study this kind of boiling with the available apparatus. Since surface condition affects heat transfer rates, three typical surfaces were chosen for study: a) as-rolled, the 2B finish received from the supplier, b) as-pickled, 30 min in 8 pct HNO3-1 pct HF, and c) as-ground on 120 grit paper. In order to evaluate the effect of improper heat treatment or welding on hot wall corrosion, both annealed and sensitized mi-crostructure were included in this study. EXPERIMENTAL Test Apparatus. The particular problems of interest in this investigation required a knowledge of the thermal gradient through the test specimen. From this gradient, the heat flux to the surface and the surface temperature could be determined. In order to satisfy this need, an apparatus similar to the boiling-disk apparatus of Fisher and whitney2 was designed. The solution is contained in a thermally-insulated, steel pipe lined with TEFLON resin. A stainless steel _______;________________________________________

Jan 1, 1970

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By C.R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

By C. R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

By H. L. Brunjes, G. B. Gould

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By H. H. Podgurski, J. C. M. Li, Y. T. Chou, F. N. Davis, R. A. Oriani

When an Fe-2 pct A1 alloy is nitrogemted at 500ºC with a gus tnixture (NH3-H2) in which the nitrogen activity has been kept Lou] enough to avoid the formation of iron nitride, a two-phase alloy is generuled which consists of AlN particles and a ferrite phase cotaining a heavy network of dislocations. The amount of nitrogen contained in such an alloy, when equilibrated with the nitrogenating atmosphere, far exceeds both that needed to satisfy the normal solution requirements of a Fe and that needed to convert all of the aluninuwi to AlN. This excess nitrogen is accounted for as being trapped on dislocations, adsorbed at the ferrite -AlN interface, and as an en-Iuznced lattice solubility in strained ferrite. This excessive uptake of nitrogen had previously been attribuled by other investigators to the formation of a nonstoichiornetric aluminum nitride. Isotope exchange experiments revealed various amomts of exchargeable N14 present in the originally nitrided samples that could not be removed by reduction with HS at 500ºC. This exchangeable nitrogen has been identified us that bound to the AlN -ferrite interface. Estimates of inter facial areas in alloys containing -3 pct by weight of A1N are as high as 10 sq m per g of alloy. ThE first1 of this series of papers described the experiments forming the basis for the elucidation of the mechanism of the formation of aluminum nitride particles within an Fe-A1 alloy. It was found that not only are dislocations necessary for the nucleation of the AlN particles but also the nitriding reaction in turn produces a dense network of dislocations in the ferrite matrix. It was also observed that nitrogen in excess of that needed for the formation of stoichiometric AIN is taken up by the alloy without the formation of an iron nitride. The present paper is an analysis of the excess nitrogen sorbed by the nitrided Fe-A1 alloy which considers the structure generated by the formation of the aluminum nitride particles. Because of the high density of dislocations, this system has proved to be quite useful in studying nitrogen-dislocation interactions. Wriedt and Darken2 have already reported such studies in a cold-worked ferritic steel. EXPERIMENTAL Nitrogen Sorption. The specimens of this alloy were cold worked (50 pct reduction) to 0.011 in. thickness and chemically cleaned in a 2:1 concentrated phosphoric acid-50 pct hydrogen peroxide solution before nitrogenation. The flowing nitrogenating atmosphere (11 pct NH3-89 pct H2) was established before the ni- trogenating temperature was reached. The same gravimetric and gas-flow equipment described in an earlier paper1 was also used in this investigation. Changes in nitrogen concentration were followed gravimetrically when establishing the isotherms. In the isotope exchange experiments, concentration changes were followed volumetrically. In some instances chemical analyses (Kjeldahl method) were used to check for material balances in both the gravimetric and volumetric procedures. Our objective was to obtain reversible nitrogen sorption isotherms for alloys equilibrated with NH3-H2 gas mixtures over a large range of nitrogen activity* and temperature. The *Defined as equal to PN H /P3/2 ,where P corresponds to partial pressure in atmospheres. Actually the nitrogen activity, aN, in the alloy equals K PNH3 /p3/2H2, where K is the equilibrium constant for the reaction NH3 = N + 3/2H2. upper limit for nitrogen activity was below that which would produce iron nitride; for reasons which will become apparent later, most of the sorption studies were made in the temperature range between 400" and 500'C. The alloy sample studied most extensively in this investigation was given a series of successive reductions (100 pct H2) and nitrogenating treatments at 500°C to attain a stabilized structure. Presumably some dislocations were lost during these treatments. Throughout most of the sorption studies, temperature was held at ± 1°C and the gas-phase composition was held to k0.2 pet NH3. Based upon the results of numerous diffusion experiments with this alloy* the 'Results to be published in a third paper of this series. times chosen for equilibration were considered more than adequate, Nitrogen Isotope Exchange. The first exchange experiments were carried out by circulating a measured quantity of H2 and NH3* (with a predetermined isotopic *The NH3 was synthesized over a synthetic ammonia iron catalyst using H2, and N2, enriched with N15. AS the NH3 was formed it was removed continuously from the gas phase by circulating the mixture through a refrigerated (78ºK) trap. When most of the nitrogen had been converted to NH3, it was distilled from the trap into a glass storage vessel. composition, N15/N14) over a nitrided specimen at 450°C in a closed glass system. Attempts to reach the exchange limit isothermally, i.e., an isotopic ratio (N15/N14) in the gas phase identical with the extractable nitrogen in the nitrided alloy, were futile. The exchange rate between the gas phase and the alloy was too slow, involving many days. To circumvent the slow exchange with the gas phase, measured amounts of N15 and N14 were introduced into the alloy by nitrogenating with an NH3-H2, mixture at 500°C containing an N15/N14 ratio of 7.76; the charged specimens were then sealed by allowing an oxide film to form over them in air, and in this final condition the specimens were subjected to 500°C in vacuum for various times during which isotope exchange was allowed to proceed within the specimen. It was estab-

Jan 1, 1970

By V. Castranova, L. Wu, K. Van Dyke, J. Gutierrez, V. Vallayathan

Since it has been demonstrated that silica caused phagocytic cells to activate lipoxygenase metabolism of unsaturated fatty acids we thought selective inhibition of this metabolic pathway might be helpful in treatment of silicosis. It is known that lipoxygenase metabolism plays a role in the pathogenesis of a variety of inflammatory and hypersensitivity conditions. Further, it is believed that the alveolar phagocytic cells which engulf silica begin the inflammatory cycle which produces the metabolic products, cytokines and growth factors which causes fibrosis in the lung. There have been indications that drugs which inhibit lipoxygenase can inhibit fibrosis from other causes. Previously, we developed a method which detects the activity of lipoxygenase metabolism by measuring free radical oxidation via light production or chemiluminescence (CL). We decided to apply this method to phagocytic cells that would be found in the lung in the presence of silica with and without newly developed inhibitors of the lipoxygenase reaction. We used drugs which inhibit lipoxygenase directly including AA861 (TAKEDA), A63162 (Abbott), and an inhibitor that scavenges free radicals produced from the lipoxygenase reaction, nordihydroguairetic acid. In addition we used an indirect inhibitor, tetrandrine. We found drug inhibition of silica activated CL from alveolar macrophages, neutrophils and human leukemia (HL-60) cells differentiated with DMSO. Nordihydroguairetic acid 2x10-5M produced almost complete inhibition in all three cell types. In human leukemia cells (HL-60) A63162 and tetrandrine were equally inhibitory at 42% while in human neutrophils A63162 and tetrandrine were less active 22 and 10% respectively. In macrophages A63162 and AA861 were less than 50% inhibitory to cellular CL at 2xl0-5M. Direct assay of tetrandrine (2x10-5M) with sodium arachidonate and soybean lipoxygenase reveals no inhibition. All antilipoxygenase drugs regardless of mechanism were inhibitory to cellular chemiluminescence from all three types of phagocytic cells. These drugs alone or in mixtures could prove useful in treatment of silicosis.

Jan 1, 1991

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

By J. S. Aronofsky

The first step in a quantitative analysis ot the mechanism of oil displacement by water in a fractured reservoir is usually conceded to be the solution of the differential equation describing the saturation distribution of two immiscible fluids flowing in a porous medium, where the capillary pressure is taken into account. In such a system the production mechanism may consist of displacement of oil both by the flow of water due to natural or artificially imposed pressure gradients and by imbibition, which implies a flow of water not due to external pressure gradients. Owing to the presence of the two oil displacement mechanisms, the mathematical model given by the differential equation intended to describe the system may not properly represent the behavior of the physical system. In fact, in the reservoir the rate of water advance may be very slow, and in the case of a fractured reservoir with a great number of large fractures, the pressure difference determining the flow of water through the matrix may be much less than 1 lb/'psi over lengths of a few feet. In such a case, imbi-bition (the exchange between oil in the matrix and water in the fractures resulting from capillary forces) may become, with time. a significant element of the production mechanism. It occurred Lo the authors, however, that without going into a physical analysis of the process of production, it might be possible by means of simple abstract reasoning to throw some light on the variation of recovery with time under conditions occurring in a highly fractured oil reservoir with rising water table. The object of this paper is to present both the reasoning and its application to a reservoir of the highly fractured type. Specifically, the analysis given here was undertaken to try to explain the increase of recovery (as defined later) with time as observed in this reservoir, without having to assume unlikely variations in the reservoir parameters with depth. This attempt has been successful as will become clear upon comparison of the computed recoveries with the actual field data. ABSTRACT MODEL Let us consider a small volume. of porous matrix saturated with oil at time, t = 0. Let the process of oil displacement by water start at time, t = t,,. At some time, t, the process will have terminated. Then a volume of oil equal to or smaller than the original oil contained in the matrix will have been produced. The first basic assumption that describes the model and guides the forthcoming reasoning is that the oil production from the small volume. dv, is a continuous monotonic function of time and that it converges to a finite limit. Such an assumption is not inconsistent with the results of laboratory waterflood tests as well as with results of imbibition tests where this is, in fact, observed. The second basic assumption is that none of the properties which determine the rate of convergence change sufficiently during the process to affect this rate or the limit. Let it be assumed that the form of the function of time relative to production from the matrix volume. dv, is given by where V,(t) is the volume of oil produced up to that time t. R is the limit toward which the recovery converges, A is a constant giving the rate of convergence, and V,(t) is the volume of oil originally in place in the volume, dv. It should be noted that recovery at time I will be understood here to he It follows that r. tends to R as t tends to infinity. CONSTRUCTION OF RESERVOIR FROM ABSTRACT MODEL Let the reservoir consist of a series of identical blocks of porous matrix stacked vertically and separated by fractures. Let each of these blocks satisfy the conditions of our abstract model. These conditions are: (1) that recovery is a continuous mono-tonic function of time converging to finite limit, and (2) none of the properties that determine the rate of convergence change sufficiently to affect the rate or the limit. Let water be rising in fractures so that oil production from any part of the block starts when the water comes in conLact with it. TOTAL RECOVERY FROM THE RESERVOIR COMPARED TO RECOVERY FROM A SINGLE MODEL ELEMENT As stipulated in Eq. 1, in the case of the abstract model,

By J. W. Goss, M. J. Coolbaugh

Most grouting has been done to stop water flaw in mines and for stabilizing foundations of various man-made structures, a survey of the U.S. literature reveals. Apparently Sun Manuel is one of the first mines in this country to use grout extensively underground for strengthening and stabilizing ground in drifts, shafts, and stations. A comparison with other procedures as well as details of the Sun Manuel program are covered. The employment of pressure grouting as a ground stabilizer at the San Manuel Copper Corp. mine reduces delays in both development and production, lowers costs, and makes possible safer working conditions. It specifically reduces delays in haulage operations and permits the maintenance of normal ventilation. In development work this grouting allows faster excavation by cementing together highly fractured or broken ground that otherwise would require extensive cribbing or spiling. In drift repair, it consolidates the loose or fractured rock over the timber or steel drift supports, thus decreasing the frequency of repair, lessening the hazards from falling rock, and curtailing delays due to blockage of drifts by muckpiles and repair operations. Pressure grouting is the process of pumping an accurately controlled mixture of cement and water into loose, fractured, or porous rock. The ratio of water to cement varies according to the nature of the rock encountered, from the thinnest mixture of 30 gal of water per sack of cement, used to fill very fine fissures, to very thick grout of 5 gal of water per sack of cement, used to fill large fissures or extensive areas of loose, broken rock. The pumping pressures at San Manuel vary from about 100 to 1000 psi, depending upon the compactness of the rock, while at other mines the pressures sometimes go as high as 5000 psi. In order to grout an area in which ground water is encountered, the pumping pressure of the grout must be increased by an amount equal to the pressure of the ground water. GROUTING IN DEVELOPMENT WORK The areas under development at San Manuel include many sections of loose, highly fractured rock. Prior to the advent of the grouting program, drifts, shafts, and stations in these areas could not be excavated without utilizing extensive support such as cribbing, spiling, and breast boarding. This slowed down the development work and increased the costs considerably over that required for excavating in more competent ground. Now, when a particularly bad area is contacted, the mining is temporarily stopped while the bad portion of drift or shaft is grouted. After the grouting is completed, the excavating is resumed with an approximate decrease of 50 pct in lost time and costs. Grouting in Drifts and Turnouts: The grouting procedures and patterns used in drifts and turnouts are very similar. The standard procedure for grouting such a turnout is shown in Fig. 1. After the ground is supported as well as possible with cribbing or lagging, the gaps between the back lagging and side lagging are plugged with empty cement sacks or additional timber, if necessary. The ground surrounding the proposed turnout is then grouted in two stages. In the first stage, the broken and caved rock is drilled and grouted to a depth of 5 to 10 ft, depending on the depth of the broken rock. This stage forms a grouted seal that allows higher pressures to be used at depths beyond 10 ft without developing excessive leaks at the face. After a grout hole is drilled, a 10-ft long pipe is wedged tightly into it with empty cement sacks. Grout is then pumped into the hole until the pressure reaches 200 to 300 psi, and the pipe is subsequently removed if it hasn't become cemented in. No more than one hole at a time is drilled and grouted because the grout has a tendency to go from one hole into another, plugging up the latter. Five or six holes are usually adequate for the first 10 ft of grouting. Experience has shown bentonite to be a useful admixture to the grout, particularly when it is indicated that the grout is being lost into large fissures or voids. Bentonite increases the plasticity of the grout enabling it to remain in place more easily until it has begun to set. In the second stage, the longer holes are drilled through the previously grouted rock, after which the

Jan 1, 1961