Search Documents

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By Eugene McAuliffe

AS this is written, the probability A is that the bituminous coal out- put for 1936 will approximate 420,000,000 tons (of 2000 lb.) with an average working time for all mines of 205 days. The results for 1935 approximated 369,224,000 tons, with the mines working about 185 days. The increase in production of 14 per cent is heartening. In anthracite, it is probable that the preliminary figures covering output for 1935, 51,- 003,000 tons, will be exceeded this year although the percentage of in- crease will almost certainly be small. The substantial tonnage of anthracite illegally mined, estimated to be 3,600,- 000 tons in 1935, with a similar large Lonnage in 1936, is in addition to the figure given above; it represents an open and flagrant disregard of law and property rights. It is hard to understand why the officials of the State of Pennsylvania do not enforce the laws against theft and brigandage, more so when the legitimate employees of the established producing proper-

Jan 1, 1937

By K. Witt, S. Steinlechner

In different nonferrous metal-producing industry sectors, the impurity element iron has to be removed from the process solution. Examples for the arising residues are jarosite or goethite precipitates from nickel or zinc production but also red mud from aluminum production. Regardless of environmental concerns, the material is landfilled in almost any case, although valuables such as indium, silver, nickel, or zinc are present in considerable amounts. Within the presented research, a low carbon dioxide emitting multi-metal recovery from such iron-containing residues by means of a selective chlorination extraction has been fundamentally evaluated by experiments but also by comprehensive thermodynamic calculations. The paper summarizes the thermodynamic fundamental concept exploited to separate the dominating iron matrix from the valuable elements and shows verification experiments in a lab size of several grams. Through thermodynamic calculations and smallscale experiments with pure metal oxides and sulfates, it has been proven that the metal chlorides AlCl3∙ 6H2O, FeCl3∙ 6H2O, and MgCl2∙ 6H2O are viable and effective reactants for chlorination. In trials with actual industrial iron precipitation residues from the zinc industry, especially, the use of MgCl2∙ 6H2O and FeCl3∙ 6H2O leads to high extraction rates for the investigated valuable metals Ag, Au, Bi, Cu, In, Pb, Sn, and Zn.

Nov 14, 2023

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM&apos;s Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

By R. W. Raymond

ALL history testifies that the mineral resources of a region have furnished both the impulse for its first development by man, and the foundation for its subsequent occupation by civilized and prosperous communities. In the pre-historic ages, the hunters, fishers, shepherds and gardeners of the world may have wandered or tarried without regard to the attractions of the mineral deposits which they could not utilize, and therefore did not value. But with the rise of civilization, as expressed in manufactures and commerce, the national value of such deposits began to be realized. Barbarous and remote tribes, possessing the sources of such supplies, won recognition in trade long before they could attain it through any other means. Thus, the North American Indians of Lake Superior exchanged their native copper for the mica of North Carolina; the ships of Tyre sailed all the way to Spain for lead and to Britain for tin; and the fleets of Solomon brought gold from Tarshish. In more modern times it has been chiefly the precious metals that have stimulated exploration and conquest. The inherent qualities and the traditional value of gold and silver sufficiently explain this historic fact, the continued existence and potency of which is evidenced, even in our own times, by the occasional rush of eager adventurers to new districts where gold and silver have been discovered. The history of North and South America has been peculiarly influenced by this factor. It was the prospect of obtaining gold and silver that led the Spanish adventurers to the shores of America, and the conquests of Mexico by Cortez and of Peru by Pizarro were inspired by the stories of the wealth of the Aztecs and the

Mar 1, 1909

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

By Gary Nash

While there could be as many directions on regulations as there are viewpoints surrounding the asbestos controversy, there are a few basic criteria that generally will influence government thinking, namely: - their definition of the problem to be regulated, - their interpretation of the scientific evidence available to them, and - their sensitivities to the views of, and the implications for, various interest groups in society. Clearly, different assessments of these criteria by various governments will lead to differing regulatory regimes. The consequence, of course, is a patchwork of non-conforming regulations among nations, with all that thin implies for the distortion of international trade and the unsettling of international relations. I would therefore argue that when governments are examining regulatory action, they should explicitly take into account their common interests in stable and cordial international relations, and when possible, efforts should be made to ensure that movement on regulation is at least, in principle, in accord with the general views of the international community.

Jan 1, 1984

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor&apos;s alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By Joseph P. DuCarme

The U.S. Bureau of Mines explored new methods and technology for extracting coal from the Appalachian Mountain region of the Eastern United States. These methods were aimed at extracting coal from thin seams and focused on the use of "roof-fall-tolerant" (RFT) mining concepts. These methods could be used on existing, abandoned highwalls or in conjunction with new highwall mining. The research was conducted using small-scale and quasi-full-scale physical models to obtain experimental results. Details are provided on (1) the quasi-full-scale model for cross-ridge mining, (2) the quasi-full-scale model for down-ridge mining, (3) the test results of these models, and (4) recommendations for future research. Significant results include demonstration of the RFT concept, a discussion of expected coal produced from these methods, and recommendations for future research.

Jan 1, 2010

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM&apos;s Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM&apos;s subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By T. V. Shockley

The Gulf Coast, from New Orleans, Louisiana to Brownsville, Texas, is one of the largest high energy consuming areas in the United States. This region has areas of very high industrial density. The lower Mississippi River from Baton Rouge past New Orleans has a high industrial density. Lake Charles, Louisiana, the Orange-Beaumont-Port Arthur area, Houston (4 separate areas) and Corpus Christi all have the same high industrial density. This situation developed due to good transportation, good labor conditions, good weather and the abundance of cheap energy-gas and electricity. Obviously the latter had the greatest impact. The availability of cheap natural gas made Gulf Coast sites very attractive to energy intensive industry such as metals and petro-chemicals. The area was also very attractive to refinery development due to the large supply (endless?) of crude oil available. As we all know, the energy situation has changed dramatically in the last five years. The cost of a MMBTU has risen from the 17¢ to 19¢ level to a price of $1.95 to $2.10. The price of interstate gas, as defined by the National Energy Plan recently passed by Congress, was approximately $1.98/MMBTU escalated to October, 1978. It goes without saying, that this has had a major impact on doing business in the Gulf Coast. As fuel prices soared, different companies responded in different ways; but overall, industrial energy consumption along the coast was reduced 20% to 25% from 1974 to 1975. Since 1975 production and energy use has been increasing, however, production at some plants is still significantly below plant capacity.

Jan 1, 1979

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.3 and 2.6 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year production period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 indexes. Initial capital investment is $34.6 million for the 1.3-MM-tpy mine and $63.5 million for the 2.6-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $50.8 and $92.2 million, respectively. These figures translate into total capital investments of $38.51 and $34.91 per ton of annual production. Assuming a desired 15-percent discounted cash flow (DCF) rate of return, with Federal income taxes at 50 percent, the required selling prices would be $13.41 and $12.27 per ton for the 1.3- and 2.6 -MM- tpy mines.

Jan 1, 1976