Search Documents

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By David J. Kusler

The Bureau of Mines reviewed current technology in the refractories consuming industries and evaluated the impact of changes in technology on the supply and demand of refractories. Literature was searched and contacts were made with leading consumers and producers of refractories. The distribution of refractories by value of shipments to users was surveyed. The report shows that the percentage distribution of refractories sales to the consuming industries has remained essentially constant during the last decade but that substantial changes have occurred in the relative distribution of types of refractories. The trend in pyroprocessing technology in recent years has been toward higher temperatures, which require more costly refractories. This fact is reflected in the impressive gain in the dollar value of refractories sales, which in 1968 was about one-third greater than in 1960, and the rapid growth of refractories based on high-alumina, magnesia, zirconia, carbon, and other materials, at the expense of fire clay, silica, and chrome- based refractories. An appendix to the report contains refractories value and shipment data tabulated in a manner by which trends in the distribution of refractory types can be observed from 1955 to 1968. In addition, unit values are presented on a per-ton basis for comparison.

Jan 1, 1970

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By J. R. Allen

Environmental laws and regulations have proliferated over the last two decades. 1/ Within the last year, Congress has dramatically expanded the scope of the Superfund program 2/ and has enacted significant new amendments to the Clean Water Act.3/ In addition, EPA has shown no signs of slackening the pace at which it promulgates new regulations to implement statutory programs. The agency projects that over the next few years it will issue approximately 275 new regulations under the statutes it implements. 4/

Jan 1, 1988

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Ellisworth R. Spencer, Lynn A. Alcorn, Peter G. Kovalchik, Adam K. Smith

Noise induced hearing loss (NIHL) is the most common occupational disease among workers in the mining industry. Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment by age 50. The Mine Safety and Health Administration (MSHA) has determined that continuous mining machines rank first among all equipment in underground coal mining whose operators exceed 100% noise dosage. The conveying system is one of the principal noise sources on continuous mining machines, due to metal on metal impacts that occur between chain flights and the conveyor deck. A highly durable polyurethane coating has been developed for the chain flights to decrease noise generated by these impacts. A continuous mining machine retro-fitted with coated flight bars has achieved overall sound level reductions of 5-7 dB in a laboratory setting. This paper evaluates the effectiveness of this engineering noise control in reducing the noise exposure of continuous mining machine operators in an underground coal mine environment. The results show that the operator of a continuous mining machine utilizing the coated flights receives a predicted 35% reduction in total work shift noise dose.

By R. Sawyer, M. Sadler, M. Holdworth

Greens Creek is a high grade Ag/Au/Pb/Zn deposit located in southeast Alaska. Maximizing the Net Smelter Return revenue from the fine grained mineralization is a dynamic process given changes in metal prices, smelting terms, ore grades and flotation characteristics. This paper discusses the evolving concentrate production strategy, and how it is affected by such factors as ore and concentrate specifications and by market conditions. Also described is the development of an on-line computer program that provides the mill operators with real time NSR data and a means for optimizing Net Smelter Return.

Jan 1, 2002

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By Tony Peach

Project Description The Ok Tedi Mine is located approximately 18 km east of the Papua and New Guinea-Indonesia border, on the southernmost extremity of the Star Mountains Range, it is situated almost equidistant from the north and south coastlines. The headwaters of the Fly River system are in the Star Mountains. The open pit mining activities are on Mt Fubilan with a (pre-mining) elevation of 2,095 metres (6,871 Feet) in the Western Province. The mine is in an area characterised by very steep topography and dense tropical rainforest. The pit has been free draining but will cease to be so in the first quarter of 2009. Ok Tedi Mining Limited (OTML) required a drainage tunnel to be driven under the mine, if possible before free drainage was no longer possible. The tunnel was required to be at least 5 m in diameter and 4,200 m (13,776 ft) long, with a possible extension of 1,100 m (3,608 Feet) if the mine decided it was required for additional drainage and underground exploration. The tunnel is being driven up grade at 0.67%, and will be connected to the pit by the raising boring of two 1.1 m (3 Ft. 6 In.) diameter shafts from the tunnel level 250 m (820 Feet) below to the pit. In Tabubil, the adjacent township at an elevation of 640 m (2,100 feet), air temperatures range from a mean at night of 20 (68°F) degrees centigrade to a daytime aver-age of 27 (81°F) degrees. Extremes of 12 and 39 (54°F?102°F) degrees centigrade have been recorded. Rain falls, on average, 339 days each year and totals 8,000 mm (315 inches), and have been known to approach 12,000 mm (472 inches) making the area one of the wettest places on earth. The portal site is at an elevation of 1,200 m or 4,000 ft and the air temperatures are a little cooler and the rainfall a little greater. Access to the mine is by air for personnel and light freight and by ship for heavier goods and materials. The port is at Kiunga on the Fly River 153 km from the portal site. The program for the project was tight, the decision to purchase the required TBM was made in July 2007 and the final decision to go ahead with the construction of the tunnel was made in November 2007.

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012