Search Documents

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

Gas well tests were performed on 17 wells in the Roma area. The procedure used in the test programme incorporates an initial isochronal test followed by what is described as the "two flow drawdown" technique. The second flow of the two flow drawdown test was conducted for sufficient time to allow transient investigation of the surrounding reservoir. This combination of tests allows the evaluation of stabilized production capacity in addition to the determination ,of several important reservoir characteristics.It also provides a qualitative indication of reserves, by reflecting the presence or absence of reservoir boundaries within the drainage area affected during the test.

Jan 1, 1968

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By W. A. Calhoun, M. M. Fine

"One of the most important wartime activities of the Bureau of Mines was the search for new sources of mineral necessary to the prosecution of the war. Part of that effort was in the form of metallurgical service extended to other government agencies engaged in purchasing and stock piling some of the more critical and strategic materials.Fluorite was one of the materials stock piled by the Metals Reserve Company. The fluorite was usually in the form of coarse metallurgical con¬centrate purchased in the United States and abroad. The material was stock¬piled to insure an adequate reserve of fluorite for the metallurgical industries. The domestic production of metallurgical fluorite containing a minimum effective calcium fluoride content of 55 percent,4/ however, gradually increased until production was at least equal to consumption. The stock-piled metallurgical fluorite, therefore, soon became a surplus commodity.On the other hand, the supply of acid-grade fluorite, containing a minimum of 97.5 percent calcium fluoride and n maximum of 1.5 percent silica,5/ was never entirely adequate. Increased consumption of acid-grade material in the aluminum, petroleum, and chemical industries kept that material on the critical list during the war.Under the circumstances, it was felt that a study of the possibility of producing acid-grade fluorite from the metallurgical stock piles would be of some benefit to the war effort. Consequently, samples of fluorite from several of the Metals Reserve Company stock piles were tested by the Bureau of Mines at the request of the War Production Board.Two groups of samples were submitted for testing. One consisted of metallurgical fluorite purchased from Mexico and stock-piled in the El Paso and Laredo, Texas, stock piles of the Metals Reserve Company. The second group of samples was from the stock piles at Gila, N. Mex.The sample submitted from the El Paso stock pile consisted of about 5,000 pounds of minus 4-inch material. Mineralogically, the sample consisted of fluorite contaminated by calcite, chert, quartz, and small amounts of iron and alumina. Although some of the fluorite was reasonably free from gangue at minus 1-inch, much of it remained locked in sizes as fine as 65-mesh.The Laredo sample was about 5,000 pounds of material from five different piles. The samples from each stock pile, A to E, inclusive, were analyzed separately to determine whether the grade of the material in the piles varied markedly. As there was little difference in the analyses, the samples were combined in proportion to the tonnage represented to make a composite sample for testing. The composite sample consisted of fluorite with small amounts of quartz, calcite, and barite. Most of the fluorite was the dark-colored, opaque variety. A small amount of iron-oxide staining was present, and traces of muscovite, clay, pyrite, and tourmaline were noted. The quartz was present as crystals in vugs, and as finely disseminated grains in the fluorite. The druzy quartz and the calcite were free at minus 10-mesh, but the disseminated grains, some of which were 1 to 15 microns in size, were not entirely free at minus 270-mesh. A petrographic estimate indicated that 65 percent of the silica was locked in the 150- to 200-mesh."

Jun 1, 1946

By García B., Wolff E.

The pellet qualities primarily depend upon the thermal profile and gaseous environment during induration. During the induration of the pellet, it undergoes physical as well as chemical changes. Physical changes are mostly due to sintering and chemical changes are due to carbon burning inside the pellet. The effect of carbon on sintering is investigated on a single pellet scale using an optical dilatometer. Sintering is a complex process that involves transportation through various mechanisms. Sintering is quantified in terms of sintering ratio and the kinetic parameter, exponent ‘n’, under isothermal conditions is deduced using the power law equation. The value of n can be used to estimate the sintering mechanism at different isothermal temperatures. Also, the activation energy is calculated using the empirical Arrhenius equation. The activation energy of 0 per cent coke and 1 per cent coke-containing pellets are 531.0 kJ/mole and 552.6 kJ/mole respectively. The order of magnitude of activation energy suggests the same mechanism in both cases. Although the mechanism of sintering is the same, 1 per cent coke-containing pellet sinters more at any isothermal temperature.

Jun 17, 2024

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By Seong-Taek Yun, Chil-Sup So, Seung-Jun Youm

The greisen-bordered quartz veins are spatially, temporally and genetically associated with a late Cretaceous granite intruding an early Palaeozoic, limestone-rich formation. Paragenetic data indicate three stages of hydrothermal mineralisation, the first typically in or within 500 m of the granite stock and showing vertical zoning between deeper Mo and higher W, the other two more abundant in the upper and outer parts of the mineralised area. Fluid inclusion and stable isotope data indicate that hydrothermal veins formed over a temperature range of 120-395 degrees C from low-salinity fluids. Early wolframite and molybdenite deposition in stage I occurred at temperatures of 300-395 degrees C from magma-derived, low-salinity, CO2-rich fluid, mainly as a result of fluid boiling and associated CO2 effervescence. Progressively larger volumes of local meteoric water entering the system led to the successive deposition of scheelite in stage I vugs, stage II base-metal sulphides and stage III fluorite-carbonates. Remobilisation of W and its later deposition of scheelite in the outer and shallower portions of the system occurred at 215-275 degrees C and stage II and III mineralisation from lower-temperature fluids that became progressively lighter in stable isotopes. It is concluded that the influx of meteoric water increased with distance from the cooling pluton

Jun 18, 1905

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of &apos;hydrochloric acid&apos; was found to give best results.

Jan 1, 1980

By Holly J

The period following World War II has seen many changes in stoping techniques at The Great Boulder Gold Mine. The new methods resulted in improved unit production figures, and have given some relief from the rising worldwide cost spiral in the post war years.Significant production figures are shown graphically in...

Jan 1, 1956

Two of the problems long associated with the complete extraction of level pillars in the wide ore bodies of Broken Hill have been: (1) The high cost of maintaining level gangways through areas of slow subsidence to provide adequate trucking roads for the transport of sand filling; and (2) The difficulty and high cost of completely filling depleted areas. This paper deals with the experiments conducted to devise an apparatus for transporting, with the aid of compressed air, sandfill from the underground sand passes to the stopes and describes the sand blower which has been developed. This apparatus has to a large degree overcome the difficulties and removed much of the hazard associated with the rapid extraction of level pillars.Special attention is drawn to the sizing analysis of the sand and to the fact that it is not dry material. It was early found that these factors were determinants in the design and development of the apparatus described.Acknowledgment is made to the General Manager of Broken Hill South Limited for permission to present this paper, to the engineering department for assisting in the design of the apparatus, and to the underground staff for their co-operation in training the operators and in bringing to success this method of stope filling.PREVIOUS FILLING METHODSThe South Mine, with a monthly production of approximately 32,000 tons of lead-sHver-zinc sulphide ore by cut-and-fill mining methods, requires about 11,000 cubic yards of filling per month. With the exception of a small and variable quantity of developmental mullock, all this filling is...

Jan 1, 1941