Search Documents

By Ming-Feng Ye, Guang-liang Wu

The microstructure and mechanical strength variations of chromite pellets preheated and roasted in air were studied systematically. The results show that the chromite (Fe,Mg)(Cr,Fe,Al)2O4 is oxidized to magnesium-rich (Mg,Fe)(Cr,Fe, Al)2O4 and ferrochromium complex oxide (Cr,Fe,Al)2O3 in the preheating process over 500 °C. When the temperature is higher than 1000 °C, the new phase (Cr,Fe, Al)2O3 is formed, which is mainly distributed in the outer layer of a single chromite particle. Inner the particles there are acicular (Cr,Fe,Al)2O3 and unoxidized (Fe,Mg) (Cr,Fe,Al)2O4, which forming an interwoven structure together. The oxidation rates of pellets can reach to superior limits in 20 min. With the temperature increasing from 950 to 1300 °C, the mechanical strength and oxidized rates increase to varying degrees correspondingly.

Mar 1, 2018

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By A. A. Davis

The decade of the 70?s saw a series of landmark environmental resource programs enacted by the Congress. Many states followed suit, so that by the end of the decade air quality, water pollution, and the conservation of other natural resources, including minerals, were the subject of a wide-ranging body of laws, policies, regulations, and procedures. Many of the actions required or permitted by this rule-making involved areas for which adequate information and substantial experience were not available. Moreover, goals and objectives were sometimes established which were enormously difficult to achieve technically, or of such formidable expense as to cause concern about their consequences in the marketplace. It is therefore hardly surprising that one product of all this activity has been a mass of litigation. Court dockets are crowded with suits and counter-suits involving both substantive and procedural aspects of environmental protection. Indeed, it is probably fair to say that the volume and range of environmentally-related disputes brought before the courts parallels that generated by the civil rights movement a decade ago. There were also some new dimensions to the environmental movement. For the first time, the national environmental policy act required agencies to prepare environmental impact statements when proposed projects or activities would have substantial impacts on environmental resources. Another requirement of many of the new programs mandated meaningful citizen participation in public decision-making. Here, as elsewhere, the purpose was admirable, but guidelines were vague, and the result often was inaction, polarization, and litigation.

Jan 1, 1986

By Evan Evans

IT is appropriate to evaluate 1947 in review as a year of a peacetime record production of about 676,000,000 tons of coal (anthracite and bituminous), closely approaching the extraordinary wartime output in 1944. Considering the general price-wage inflation, it is in point to note that the coal industry sustained the highest wages paid to workers in any major industry, but that coal prices at wholesale levels have risen much less percentage wise than the average for all commodities. The sellers' market continues to prevail. In addition to serving our own country's enormous needs, our coal industry is exporting extraordinary tonnages overseas. This unusual export demand is likely to continue for a while. Moreover, the demand in Europe for American coal mining machinery is a real tribute to the management efficiency of our modern mechanized coal industry. Competitively, the petroleum industry is concerned over its long-term supply, and already a synthetic fuels industry is being publicly advocated. In due time coal and lignite are bound to be

Jan 1, 1948

By Randall M. Wheeler

Many of us have used a seismograph to measure peak particle velocity and frequency. But do we really understand why? Also, why do we measure particle velocity instead of displacement and/or acceleration? What is the vector sum? How do these items relate? Where does frequency fit in? This workshop will attempt to answer these and other questions. Some of the answers may surprise you, others may not.

Jan 1, 1997

By Z. R. Llanos

This paper presents a review of industrial and experimental processes for the recovery of molybdenum, vanadium, nickel, cobalt and aluminum from spent hydrotreating or hydrodesulfurization catalysts. Numerous processes have been developed in a laboratory and pilot scale. However, worldwide, there are only four well established commercial facilities currently in operation. The installed capacity of these facilities exceeds the availability of spent catalysts and may be sufficient to assimilate future increases of spent catalysts. Despite liability risks; significant quantities of spent catalysts are still being landfilled. Changing regulations that may affect the future handling and disposal of spent catalysts are also reviewed.

Jan 1, 1995

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By S E. Wallah, D Hardjito, B V. Ran

The manufacture of Ordinary Portland Cement (OPC) is not only energy-intensive but also releases a significant volume of carbon dioxide (CO2) to the atmosphere. In addition, OPC in concrete often causes premature deterioration that affects the durability of concrete structures. This paper explores an alternative to OPC concrete called geopolymer concrete.The present research utilises low calcium (class F) fly ash as the source material to produce geopolymer concrete. Several factors that affect the mix design process such as mix proportion, curing time, and curing temperature have been studied. In addition, the long-term properties such as drying shrinkage, creep, and exposure to sulfate attack are also being investigated.The test data presented in this paper reveal that geopolymer concrete possesses high compressive strength, undergoes very little drying shrinkage and moderately low creep, and shows excellent resistance to sulfate attack. The result is extremely promising and demonstrates the sustainability of geopolymer concrete as a construction material for a sustainable future.

Jan 1, 2004

By W. F. Baker

Location and History God's lake is in the northeastern part of Manitoba, about 400 miles northeast of Winnipeg, or about 250 miles due north of Red lake, Ontario. The lake is quite large, having an overall length of 54 miles and a maximum width of 18 miles. There are numerous islands in the lake, the largest of these, known as Elk island, being about 15 miles long and 3 miles wide in the widest part. The accompanying map (Figure 1) shows the location of God's lake and of the mine. The God's Lake area has long been regarded as promising country for the prospector, but, due to its inaccessibility, practically no prospecting was done prior to 1927. In the years 1927-1931, inclusive, a few prospectors visited the area, but no discoveries were made. In 1932, Bob Jowsey and Archie McDonald entered the area from Island lake. They first prospected in the vicinity of Knife lake, which is immediately south of the main part of God's lake, and then moved on to the latter lake, heading for the north shore of Elk island. The first afternoon on God's Lake, when looking for a place to camp on the north shore of what is now known as Jowsey island, Jowsey discovered a quartz porphyry dyke which was cut by a number of gold-bearing bluish quartz stringers. On the strength of this discovery, he and McDonald began at once to stake the Reno group of claims. Rumours of the discovery brought in other prospectors, and other groups of claims were staked to the east, along the north shore of Elk island. A second discovery was soon made by Dan McCrea on his Gold Standard claims, three and a half miles to the east of the original discovery. Staking still continued to the east, along the north shore of Elk island, and Bob Brown and Harvey McKenzie staked the Akers group on a discovery approximately two miles east of McCrea's discovery. Through the efforts of Jowsey, the Reno, Rand, Elk, and Cona groups, belonging to the original syndicate for which Jowsey and McDonald staked, were combined with the Gold Standard, Greenstone, and Akers groups, and the Company known as God's Lake Gold Mines, Limited, was formed. Several additional groups of claims were later taken over by the Company and a considerable area of adjoining ground was staked to round-out the property.

Jan 1, 1935

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By G. W. Jones

One of the major activities of the Bureau of Mines is the promotion of safety in mining and other industries, In this connection, the Bureau determines the explosion hazards' of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. Many dangers are likely to confront men who must enter a building immediately after it has been damaged. Rescue workers must watch constantly for common gases and vapors that may be present in dangerous concentrations in and about demolished, buildings. Fuel gas is the most common source of danger, although refrigerants, gases from furnaces, flues, fires, sewers, and industrial processes, and gas from bomb, explosions in confined places also constitute definite hazards. To rescuers and trapped casualties, these gases offer the hazards of (1) explosion, (2) toxic effects, including asphyxiation and death, and (3) displacement of air so that the oxygen content of the atmosphere is reduced to or below the danger level.

Jan 1, 1944

By Neldon L. Jensen

Although ASARCO Incorporated, the only domestic producer, had terminated copper smelting operations and associated recovery of byproduct arsenic trioxide at Tacoma, WA, in 1985, it shipped small quantities of both trioxide and metal from its remaining stocks in 1986. Imports for consumption of arsenic trioxide increased significantly, owing to increased demand for arsenical wood preservatives and the decrease in domestic shipments of trioxide. Prices remained unchanged throughout the year. Development of gallium arsenide integrated circuits, important in advanced military and commercial electronics circuitry, continued to gain momentum during 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide and metal from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1988

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011