Search Documents

Every automatic citizen is an automatic recipient of a miner's right under the present Mining Act (Chapter 195), but this alone does not entitle any automatic citizen to mine for minerals on any land, even his customary group's land. Without complying with requirements of the Mining Act, any automatic citizen who engages in mining solely on the basis of a miner's right would be mining illegally. He would also be engaged in illegal mining if he mines on customary or other non-government land. Even if mining is legally pursued by an automatic citizen, he does not acquire ownership of minerals without first making the required royalty payments to the State.

Jan 1, 1991

By Edward DeLilla

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to increase productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: -Prudent engineering. -Proper planning. -Realistic feasibility studies. -Effective specification. -Thorough training of the mine personnel.

Jan 1, 1994

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By Ralph Dawson

The following additions to SLP-4 “ALWAYS AND NEVERS” have been approved by the Board of Governors since the last printing 6/97 and will be included in the next printing soon. They are also included in the Second Printing of the 17th Edition of the ISEE Blasters Handbook. Review them and apply those which might be applicable into your blasting program now.

Jan 1, 2001

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By T Graham

Traditional iron ore wet beneficiation plants are large multilevel structures, often integrated into centralised processing plants. They are characterised by sizeable footprints, substantial water and power consumption, inflexible design and low scalability. Significant design changes that address these issues need to be made before relocatable modular plants become feasible. Firstly, large amounts of processing water are required in standard wet plants, so it is vital that water consumption is reduced to an absolute minimum. Secondly, the process of depositing tailings into tailings storage facilities (TSFs) is environmentally destructive, consumes significant power and requires lengthy approvals to be completed. Thirdly, modules need to be easily and quickly relocatable.The solution to reducing water usage and eliminating TSF requirements is accomplished by providing a tailings dewatering and dry-stacking capability into a separate module. This equipment needs to dewater tailings to a point (typically below 20 per cent moisture) where dry stacking becomes possible – design is mainly driven by material rheology and particle size distribution (PSD). In this respect, a flexible and scalable strategy is employed to dewatering modules, allowing a variety of components such as dewatering cyclone clusters, paste thickeners, fine mesh vibrating screens and filter presses to be used to achieve the necessary moisture level, enabling the final dry stacking to be accomplished by a simple telescopic stacking system. Plant relocatability also requires modules to comply with mass and dimensional constraints, as well as ‘plug and play’ ease-of-use features.For coarse particle upgrade, jigs provide a low-cost and effective solution, whereas fine and ultra-fine Fe units can be recovered using Wet High Intensity Magnetic Separation (WHIMS). Recently, sensor sorting – a dry process using X-ray fluorescence, X-ray transmission, laser or other sensors – has begun to make an impact in coarse particle separation, although capacities are still low. The overall objective of a plant is to provide an Fe upgrade of four to five per cent with a feed of up to 4 Mt/a and a recovery of approximately 50 per cent.CITATION:Graham, T, 2017. Relocatable modular beneficiation creates value from waste, in Proceedings Iron Ore 2017, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Satya Ganti, Bryan Turner, Bill Davis, Veeraraghavan Sundar

This work presents a three dimensional microstructural analysis of medium carbon steels, based on serial sectioning using optical microscopy. The microstructural phases considered here are ferrite and pearlite. Typically conventional 2D microscopy is used to analyze these phases (ASTM E112-13 in Standard test methods for determining average grain size. ASTM International, West Conshohocken, PA, 2013), with eddy current (Khan et al. in J Mater Process Technol Freitas et al. in Mater Sci Eng A 527(16):4431–4437, 2010) as alternatives. Medium carbon steel samples were heat treated in a furnace and either slowly cooled in the furnace, or cooled at higher rates. This resulted in different pearlitic microstructures in the samples. The analysis was conducted with Robo-Met.3D®, a fully automated metallography system for serial sectioning. Based on optical microscopy, volume cubes of hundreds of microns on edge were imaged and reconstructed to conduct grain size and phase volume analysis. The system proved capable of collecting image data with high fidelity, and controlled slice thickness in an automated manner. The resultant dataset was useful in visualization and analysis of pearlite and ferrite phases in steel samples.

Mar 1, 2018

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2is reduced to Ti2O3.One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By K Thorpe

Amorphous silica deposits have been identified at Tikitere and Taheke near Rotorua. Two areas at Tikitere have been surface sampled and drilled to establish a resource of amorphous silica in excess of one million tonnes. A pilot plant was established to develop a process to manufacture a high quality super pozzolanic material. This development process took two years before a commercial product was introduced to the construction industry in 1996. The amorphous silica product, marketed as Microsilica 600, is used as a pozzolanic material to produce high quality strong and durable concrete, sprayed tunnel linings, mortars and grouts. Microsilica 600 has been used locally and exported to 11 countries.

Jan 1, 1999

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

By Carlos Virrueta Zevallos

El presente texto describe los lineamientos necesarios para construir un sistema de control de perdidas sólido en la Corporación HOCHSCHILD MINING DNV, el cual se basa en un liderazgo, compromiso y administración efectiva del sistema como puntos vitales para el éxito, protegiendo la vida de las trabajadores, la propiedad, los procesos y medio ambiente.

Sep 12, 2011

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009

By R. E. de Barrio, M. E. Lanfranchini, R. O. Etcheverry

"The El Abuelo Ca-Fe-magnetite skarn and related hydrothermal quartz veins are located at Cerro Pepita Hill, in southwestern Chubut province of southern Argentina, 1700 km southwest of Buenos Aires. These deposits are developed in a continental magmatic arc environment linked to the Andean orogeny. Iron skarn mineralization is mainly hosted by an Upper Jurassic to Early Cretaceous sedimentary sequence interbedded with Upper Jurassic basaltic andesite, and is spatially associated with Early Cretaceous calc-alkaline dikes. Ore grades vary between 40 and 63 wt.% Fe. In addition, anomalous metal contents (>10 000 ppm Cu and up to 81 g/t Ag) are present in the hydrothermal quartz veins.At least three paragenetic mineral assemblages have been identified in the El Abuelo exoskarn: (1) amphibole > epidote ± chlorite ± quartz, formed by isochemical contact metamorphism; (2) Fe-clinopyroxene ± Ca-garnet, formed during prograde metasomatic anhydrous exoskarn formation; and (3) actinolite ± epidote ± chlorite ± quartz ± magnetite > titanite, resulting from hydrous retrograde alteration of exoskarn. Endoskarn alteration involved an early Mg-Fe-clinopyroxene ± Fe-garnet assemblage followed by retrograde actinolite replacement of pyroxene. Lower temperature hydrothermal alteration related to quartz veins was superimposed on the skarn assemblages, showing an innermost sericite ± adularia ± pyrite ± chalcopyrite assemblage and an external propylitic halo.Some metallogenic characteristics of the mineralization and the geological setting resemble those in several iron oxide copper-gold deposits elsewhere in the world."

Jan 1, 2007

By J W. Simmons, T H. Antoun

"Rock fragmentation is an important component of explosive mining and excavation techniques andis the culmination of a damage accumulation process dominated by crack propagation. During the past 20 years, improved computer modeling of this process has resulted in new and promising computational tools for improving explosive mining and excavation procedures. This paper discusses one of these new computational tools, a computer model called BFRACT."

Jan 1, 1995