Search Documents

By K S. Fisher, J D. Pease

The installation of the George Fisher flowsheet in the lead/zinc concentrator at Mount Isa Mines Limited has recently been completed. The George Fisher flowsheet involved moving flotation capacity from the lead circuit to the zinc circuit and changes in zinc circuitry, changes in the reagent regime and increased regrinding capacity, using IsaMills, to regrind some streams to 80 per cent passing seven microns. The project was highly successful, delivering a five per cent increase in zinc recovery within a fortnight of commissioning. The George Fisher flowsheet was developed over six years. Laboratory work built upon the knowledge gained from investigating and processing the Mount Isa and Hilton orebodies. The engineering design and construction for the brownfield expansion of the existing lead/zinc concentrator had significant involvement from the operational, maintenance and technical personnel. Experienced personnel were seconded from the concentrator to the design and construction groups to ensure smooth integration of the new flowsheet into the existing concentrator with minimum downtime, and maximising the reuse of existing equipment. The combination of thorough design, good project integration with operations, and a good commissioning plan allowed almost immediate delivery of project gains. The project was highly successful, the full design improvements were achieved within two weeks, allowing the focus to move to developing future improvements.

Jan 1, 2000

By C. K. Rose

A hydraulic scaling rig was placed in operation at the Bureau of Mines oil-shale mine near Rifle, Colo., in 1953. The rig consists of a self-leveling platform mounted on a hydraulic-powered boom. The boom is mounted on the bed of a diesel truck. The equipment provides a movable work platform from which two men can work in safety and comfort while barring loose rock from the backs and walls of the rooms, pillars, and haulageways. INTRODUCTION As a part of its synthetic liquid fuels program the Bureau of Mines has developed a mine in the richer oil-shale beds of the Green River formation near Rifle, Colo. An important part of the work of the Oil-Shale Mining Branch is investigation of techniques for low-cost mining of oil shale on a commercial basis. It is evident that scaling loose rock from the high backs and walls of the mine represents a portion of the direct mining cost. This paper describes the development of a scaling rig for operation in the upper heading of the mine, which is 39 feet high.

Jan 1, 1954

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By H. J. McQueen

ORDER OF PRESENTATION ?INTRODUCTION TO THE VICTORIA BRIDGE ?REASONS FOR A BRIDGE AT MONTREAL ?RAILROAD BRIDGE REQUIREMENTS ?IRON PRODUCTION CANADA / WORLD AL ?METALLURGICAL INDUSTRY CANADA ?FAIRBAIRN, STEPHENSON SHIP PLATE-RIB BOX GIRDER ?VICTORIA BRIDGE (PREFABRICATED BRITAIN) ?IRON ORE SITUATION THE VICTORIA BRIDGE 1859, TUBULAR -WROUGHT IRON* 1898, TRUSS ?STEEL* (*HOT RIVETED) 1957, SPUR, LIFT SPANS ??DUCTILE WROUGHT IRON WITHSTANDS FATIGUE ?TO KEEP THE TRAINS ON TIME & ON TRACK? ??IMMOVABLE SHARP PIERS SPLIT ?THE IRRESISTIBLE ICE, STOPPED CITY FLOODS? ? ?********* ??111 YEARS-YOUNG STEEL TRUSS, (1898): ?STILL VITAL SEA-T0-SEA RAIL LINK? ? ?********* ??51 YEARS HAVE PASSED SINCE SEAWAY (1958) ?SWITCHED BRIDGE INTO DOUBLE LIFT SPANS?

May 1, 2011

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

By S Prakash, M Danish, D Kumar

The green energy transition is speculated to cause an increase in the demand for raw materials while recycling rates are improving; discoveries are required to maintain supply. Geological remote sensing offers a cost-effective way of exploring mineral resources. While satellite and airborne imaging are routinely used for exploration targeting, a gap remains at the outcrop scale. Hyperspectral imaging (HSI) is advantageous for large-scale regional mapping, typically performed from satellite or airborne platforms. Accurately mapping geological lithologies remains challenging in inaccessible areas, such as rough terrain or mine sites. Proximal sensing techniques can boost geological activities’ reliability, safety, and efficiency in exploration or during mining activities. It also generates objective, reproducible results and valuable raw data that can be archived, further processed, and re-interpreted. Ground-based hyperspectral imaging of outcrops has steadily increased during the last decade due to sensor development and better processing routines. There is often a big technology gap related to mineral mapping, integration of images and spectra (reduction in manual identification of minerals and types) and hyperspectral data visualisation through remote sensing. TEXMiN Foundation, in collaboration with its industry partner Dassault Systemes Foundation, carried out the project, ‘Developing Hyperspectral Image Processing and Analysis, build a rich library of Hyperspectral images of a vast range of minerals from India which will help in increasing prediction accuracy of mineral deposit for mining exploration’.

Sep 1, 2024

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By P E. H Gregg, D Horne, R B. Stewart, N Bolan

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100 000 mm of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity inNew Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.   The suitability of the tailings as a potential plant growth medium was assessed with the end view of revegetating the tailings dam and alleviating AMD. This paper outlines characterisation work conducted on the tailings and summarises preliminary results from plant growth trials. The tailings contain up to 5% Fe, 1.15 % Pb, and 0.45% Cu in the form of sulphide minerals. The distribution of heavy metals, sulphate and total sulphur with depth indicates that the top 200 - 300 mm of the tailings have been extensively weathered since their deposition. The oxidation of sulphide minerals, particularly pyrite (FeS2 ) has reduced the pH of the tailings to nearly 2 in places. Below 300 mm the sulphide minerals are largely unweathered and the theoretical acid generating potential of the tailings exceeds 170 Mg CaCO3/1000 Mg tailings at certain depths. Plant growth trials were conducted to study the effects of lime and organic matter addition on the establishment of vegetation on the Tui mine tailings. Several plant species were assessed including some cultivars bred for their tolerance of heavy metals.

Jan 1, 1995

On the Role of Dixanthogen in Froth Flotation

Sep 13, 2010

By J L. Merritt

The mining industry seeks to engage with and respond to stakeholders through open consultation processes during the various phases of a mining project (Department of Industry, Tourism and Resources, 2006). Two Australian Coal Association Research Program (ACARP) funded projects conducted in the Bowen Basin coalfields in Central Queensland investigated the use of a stakeholder panel for the evaluation of mine site rehabilitation. The panel members were drawn from the local and regional area, and represented neighbouring landholders, traditional owners, AgForce, local government, conservation groups and non-governmental organisations (NGOs) such as Greening Australia and the Fitzroy Basin Association. The approach of utilising stakeholders to establish rehabilitation criteria was proposed as an alternative to the established practice of assessing rehabilitated areas against a suite of quantitative completion criteria; eg >70 per cent vegetative ground cover or <5 t/ha/a soil loss. The basis of this approach recognises the reality that the definition of completion criteria has proved problematic over the last 40 years with no broad consensus reached on the suite, let alone the metrics; eg the exact cover level that will benchmark acceptance of the mine site rehabilitation.CITATION:Merritt, J L, 2016. Zooming out – learning to see rehabilitation through stakeholders’ eyes, in Proceedings Life-of-Mine 2016 Conference, pp 163–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Betty L. Gibbs

A clear and accurate knowledge of the status of ventilation in an underground mine is essential to continuing safe operation. In a small mine with a few working faces, the problem is simple and can easily be solved by choosing the appropriate fan. In larger, more complex mines the problem of supplying the working faces with fresh air is a problem beyond the scope of 'finger in the wind' analysis. In today's climate of stiffer government regulation and mining company concern for the safety of workers, computer programs which analyze ventilation networks are helping mining companies meet the standards. The development of computer programs for ventilation network analysis is summarized. Early programs were developed at universities or government agencies and required large expensive computers. As computers have become smaller and less expensive, the development or revision of programs for micro computers has become more available. Prices have lowered to the point of affordability even for medium and small companies. A list of ventilation network analysis programs is provided along with a summary of capabilities, costs, and hardware requirements for each program.

Jan 1, 1987

By Launa G. Mallett, Dana Reinke, Charles Vaught, Michael J. Brnich

As mines become safer and major disasters fewer, the number of experienced emergency responders is decreasing. This decrease will create a gap in response expertise which could have serious ramifications during future mine disasters. While working toward safety goals which may make emergency response obsolete, it would be reckless not to acknowledge that the potential for disaster still exists and that the protection of miners in such circumstances must remain a priority. The Mine Emergency Response Interactive Training Simulation (MERITS) is a computerized mine emergency simulation that meets a variety of needs. It allows personnel in leadership positions to test their knowledge and skill. Groups of individuals composed of representatives from mining companies, labor, and government agencies can practice working together during the simulated mine emergency much in the same way an actual emergency would require. An individual could also run the program to enhance his or her response skills. With this training tool, responders will be able to learn from their mistakes before facing situations with potentially catastrophic consequences. This paper discusses MERITS and its use in providing command center training.

By Jinrong (Patrick) Zhang

Improvement of conventional flotation efficiency, separation of carbonates from apatite, recovery of phosphate values from phosphatic clay and other ways of utilizing the clay, disposal of clay slurries and subsequent reclamation of the settling areas, and conservation of resources and energy remain major challenges in the beneficiation area for the phosphate industry. These problems have been actively investigated by the industry, government agencies, and research organizations for decades with modest success. However, some recent research activities have generated promising results and possible new technologies. The dominant position of the Crago process in phosphate beneficiation is being challenged by some of the single stage processing schemes. Heavy media separation enables one producer to process a portion of high carbonate ores. Separation of dolomite from apatite by reverse flotation of carbonates with phosphate depressants showed potential for industrial application. Consolidation of phosphatic clays in mine cuts using a modified "sandwich" process is being tested. Beneficiation in the acidulation plant or grinding at the mines may be considered in the future.

Jan 1, 1993

The Hishikari gold deposit, discovered by the Metal Mining Agency of Japan, has become a giant class epithermal gold deposit with the highest grade of gold yet recorded in the world through detailed exploration and development by the Sumitomo Metal Mining Co., Ltd. The exploration strategy involved a regional approach combining geological and gravity surveys over a 900 km2 area which had historically produced over 120 t of gold. These surveys were carried out to grasp the common geologic features of epithermal gold deposits in the survey area. A genetic model for epithermal gold deposits in the area under regional survey was also considered based on detailed research of the Kushikino epithermal gold deposit which was in operation at that time. This model was applied to the targeted areas, and important relationships between mineralization, host lithology, intensive propylitic alteration and gravity highs became apparent. The Hishikari block was selected in this way and bonanza gold was discovered during drilling. Since the development of the Hishikari mine, information useful for further exploration for the same type of deposit has been accumulated.

Jan 1, 1995

By J. B. Conway

Stress-vuptuve data for several of- the refractory metals are frequently found to yield a linear relationship between the Larson-Miller parameter and the logarithm of the applied stress. In such cases linear stress-rupture isotherms result with slopes bearing a definite relationship to the temperature. It also follows that the stress to produce rupture in a certain period of time will be linear in temperature. Data for several refractory metals have been reviewed and excellent linearity is shown in this type of isochronal plot. In addition, the af ore - mentioned lineavity leads to a linear relation between the log of the stress to produce rupture in a certain time and the homologous temperature. This has been illustrated for the Group VI-A metals, tungsten and molybdenum. EXTENSIVE use has been made of the Larson-Miller' parameter in the interpolation and extrapolation of stress-rupture and creep data. In those cases where this particular parametric approach is applicable a convenient and fairly straightforward procedure is made available for the correlation of experimental stress-rupture data. It is quite common to employ this parameter in the form of a master rupture plot in which the parameter, T(C + log tr), is expressed as a function of log stress. In many cases this functional relationship in log stress is linear within acceptable accuracy and hence the following relation results: where P is the parameter, C is the Larson-Miller constant, T is the absolute temperature, t~ is the rupture time, a is the stress, and a and b are constants. Examples of such a relationship are contained in the work of Green, Smith, and 01son2 dealing with high-temperature rupture behavior of molybdenum and in the work of Green' dealing with the high-temperature behavior of tungsten. In addition, pugh4 has shown a similar linearity for some fairly low-temperature data for molybdenum. It can be shown that when the relationship in Eq. [I] is exhibited certain generalizations can be made concerning the form of the stress-rupture isotherms. For example, rearranging yields: For a given material (constant C) at a given temperature the first term on the right-hand side of Eq. [2] is a constant and hence this equation defines a straight line when log stress is plotted as a function of log-rupture time. This is recognized as the standard form usually employed in this type of data presentation. Such linearity then suggests the linear form of the Larson-Miller parameter. Or, in other words, the linear parametric relationship in Eq. [2] results only when the stress-rupture data are linear on a log-log plot of stress vs rupture time. Another interesting observation can be made in regard to Eq. [2]. It can be noted that the slope of the stress-rupture isotherms is given by - T/b and hence a direct calculation of the constant b is available. It also follows that since the value of b is the same for all temperatures the slopes of the various isotherms on the log-log stress-rupture plot cannot be the same. Indeed, the existence of the relationship in Eq. [2] precludes a system of parallel lines on this common stress-rupture plot. As a matter of fact it further specifies that in addition to being nonparallel the slope of these isotherms must decrease (i.e., become more negative) with increasing temperature. Such a condition is indeed found to exist in the case of the stress-rupture data reported for molybdenum.' As a corollary to the above, it may be stated that stress-rupture data which do not lead to a linear log-log stress-rupture plot or whose isotherms do not exhibit a decrease in slope as the temperature increases will not yield the linear relationship of Eq. [I]. Applying Eq. [2] to two different temperatures and solving for C yields: Eq. [3] affords a simple and rapid method for calculating the Larson-Miller constant from the log-log stress-rupture plot. The slope of a given linear isotherm is measured and the value of "b" calculated based on Eq. [2] as: slope = - -Tb Then at an abscissa value of 1.0 hr (making log tr in Eq. [3] equal to zero) read the stress corresponding to rupture for two different temperatures. Substitution in [3] yields: A value of the Larson-Miller constant can thus be calculated from a few simple mathematical procedures employing data read directly from the log-log plot of the stress-rupture data. Of course, it is not to be overlooked that the above reasoning has been based on the linear relationship of Eq. [I] being applicable. However, if as mentioned above the log-log plot is

Jan 1, 1967