Search Documents

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been pubished.4/

Jan 1, 1938

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been published.4/

Jan 1, 1938

By N. A. C. Smith, E. W. Dean, W. A. Jacobs, H. H. Hill

Fractional distillation is the most important process in the commercial refining of petroleum. The same procedure, conducted on a small scale, is the basis of a number of analytical methods of wide application in the petroleum laboratory. The Bureau of Mines has studied apparatus and procedure for the distillation analysis of petroleum, and this report is presented as a record of developments up to the present time. The work is incomplete, but the extensive information that has been obtained to date is made available as a guide in handling laboratory distillation problems. The analytical distillation of petroleum is commonly made to determine range of boiling points or to separate the oil. into fractions for detailed examination, or both. When only one of these two ends is sought the procedure involved is notably simpler than when, as is more common, information is required regarding both boiling range and properties of fractions. Moreover the degree of minuteness of measurement and the accuracy of the data required from analytical distillations differ considerably. Often the simplest sort of comparative figures are satisfactory; other tests require complicated and highly tedious procedure. No one distillation method is universally applicable, and it is impossible for anyone group of investigators to foresee all the different kinds of requirements that may occur in the industry.

Jan 1, 1922

By John J. Baz-Dresch, Kenneth L. Bickel, Winthrop F. Watts

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel- powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the mine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 1994

Two of the problems long associated with the complete extraction of level pillars in the wide ore bodies of Broken Hill have been: (1) The high cost of maintaining level gangways through areas of slow subsidence to provide adequate trucking roads for the transport of sand filling; and (2) The difficulty and high cost of completely filling depleted areas. This paper deals with the experiments conducted to devise an apparatus for transporting, with the aid of compressed air, sandfill from the underground sand passes to the stopes and describes the sand blower which has been developed. This apparatus has to a large degree overcome the difficulties and removed much of the hazard associated with the rapid extraction of level pillars.Special attention is drawn to the sizing analysis of the sand and to the fact that it is not dry material. It was early found that these factors were determinants in the design and development of the apparatus described.Acknowledgment is made to the General Manager of Broken Hill South Limited for permission to present this paper, to the engineering department for assisting in the design of the apparatus, and to the underground staff for their co-operation in training the operators and in bringing to success this method of stope filling.PREVIOUS FILLING METHODSThe South Mine, with a monthly production of approximately 32,000 tons of lead-sHver-zinc sulphide ore by cut-and-fill mining methods, requires about 11,000 cubic yards of filling per month. With the exception of a small and variable quantity of developmental mullock, all this filling is...

Jan 1, 1941

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By H. J. Ilgner

The paper reviews the results to date of an integrated research programme currently being conducted by CSIR Mining Technology, aimed at impacting significantly on concentrated mining with face advance rates of up to 20 times faster than presently achieved. Consideration is given to the interplay between innovative technologies for continuous non-explosive mining or rock comminution underground and lateral hydraulic transportation in cross cuts, haulages and eventually hydro hoisting. Novel technologies for underground comminution of reef and development waste and an innovative pumping system suitable for the hydraulic transportation of coarse comminuted rock are reviewed. Emphasis is placed on South African gold mine reef and waste samples comminuted by electric shock wave comminution technology. The innovative TORE® pump system appears to be well suited for the successful hydraulic transportation of rock, produced by electric shock wave comminution, at solids concentrations between 45 % and 67 % by mass.

Jan 1, 1997

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per 'min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102' dry-bulb and 93' wet-bulb.

Jan 1, 1937

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Frank E. Woolley, Robert D. Pehlke

Jan 1, 1965

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Large scale fluid extraction from the Latrobe Group in the Gippsland Basin is occurring as a result of offshore petroleum production and coal mine dewatering in the Latrobe Valley. Groundwater extraction in the Latrobe Valley exceeds recharge and is causing an expanding area of declining hydraulic head in the Latrobe Group, and regional land subsidence which is well documented. Recently the government water sector completed the installation of a network of Latrobe Group monitoring bores in the remainder of the onshore part of the Gippsland Basin. The bores situated along the coastal area show a steady decline in hydraulic head of about 1 m/year which can be attributed mainly to petroleum production.

Jan 1, 1992

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptability. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new combination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmission to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 1, 1950

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By Q. X. Yun

This paper provides a new approach to optimize the production planning in underground mines by means of evolutionary algorithms. Firstly, genetic algorithm is used to reach the global optimization in planning. Then, evolutionary programming is employed to obtain the partial optimization for each year. The application proves that the new approach is reasonable and useful. Keywords: Evolutionary algorithm, Genetic algorithm, Evolutionary programming, Optimization, Mining engineering.

Jan 1, 2003