Search Documents

By Ernest N. Patty

WHEN an Alaskan prospector makes a new mineral discovery he stakes out his claims and then starts prospecting for a near-by landing field. This may be a convenient lake but more often it is a gravel bar along a river, where, by cutting off some brush and throwing the larger rocks to one side and then tying a flour sack to a pole, he may decoy some intrepid aviator into testing it gingerly with the wheels of his plane. It was only a few years ago that .the fence around the baseball park at Fairbanks, Alaska, was taken down so that planes could get in and out of the ball park without ripping off boards. Today the grandstand is lost among the modern hangars which line one side of a modern and busy airport. Planes come and go all during the day, and in summer, when there is no darkness, the night stillness is frequently broken by the hum of a motor overhead. Fairbanks is the hub of interior Alaska and from that hub airplanes radiate in all directions to mining camps large and small. An air industry of comparable size is based at the town of Anchorage, and in fact there are but few towns of more than 200 population in the Territory that do not have one or more planes based there.

Jan 1, 1937

By T. Cameron Kenney

INTRODUCTION Whereas the design of rock slopes in open-pit mines is done largely by mining engineers and geologists, the design of slopes in overburden at this point in time is a problem for which civil engineers or geotechnical engineers are best prepared to deal. The reasons for this situation are to be found in the educational curricula and the technical journals of the two groups, where soil mechanics has received little attention by mining engineers and geologists, and rock mechanics has similarly received little attention by civil engineers. In ten years' time this paper will hopefully be considered by young mining engineers to be a repeat of the material that they studied at university. However, even in ten years time I believe that the civil (or geotechnical) engineers will be extensively used as consultants on overburden- slope problems of open pit mines because mining companies will find this more expedient than maintaining their own geotechnical staff, special field equipment and special testing laboratories. For this reason, the purpose of this paper is not to condense several university soil mechanics courses into a twenty-page text for mining engineers and geologists. Rather, the purpose of the paper is to offer a general explanation of various factors affecting slope stability so that mining engineers and geologists will have a better understanding of the behaviour of overburden soils in slopes. A great deal has been written in soil mechanics literature on the subject of slope stability. No attempt will be made to reference all this material but rather only a selected number of references will be cited. Excellent general treatments of the subject of stability of overburden slopes are available (1,2,3,4). Further information of a more specialized nature is to be found in such publications as the Journal of the Soil Mechanics and Foundation Division of the American Society of Civil Engineers, Geotechnique (printed by the Institution of Civil Engineers, England), Canadian Geotechnical Journal, and the proceedings of the conferences of the International Society for Soil Mechanics and Foundation Engineering. FACTORS INFLUENCING SLOPE STABILITY There are two general scales of slope-stability problems, gross stability and local stability. Gross stability refers to large volumes of soil, and gross instability would involve large rotational-type shear failures. Local stability refers to something much smaller and examples

Jan 1, 1972

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By Richard L. Stotlar

Introduction During the last decade, the metallic minerals segment of the industry could be categorized as a "feast-or-famine" business. It is no secret that metallic minerals are cyclical. Employment opportunities greatly depend on the supply and demand for its mineral products. It is also not unusual for there to be a lag between the industry's manpower requirements and academia's ability to produce new graduates. Due to this lag, there will be years with manpower shortages, as in the mid-1970s. At other times, supply will exceed demand. The question is where will the jobs be in the years to come? This presentation will review reasons why employment opportunities have declined within the metallic minerals industry. It will also predict future demand for mineral engineering graduates. And it will outline strategies for obtaining an employment offer. Historical Review - Employment From 1977 through 1983, about 75% of all metal mining employees were directly engaged in production activities, down from 83% in 1965. This decline reflects increased use of labor saving equipment, and more government regulation and foreign competition. Metal mining's employment decreased from 74,000 jobs in 1982 to fewer than 68,000 in 1983 - an 8% decline. The overall industry is having these problems because of the general downturn in the economy. For example, at the beginning of this decade, US automobile and steel industries were in trouble. Interest rates were too high and volatile. This adversely affected construction, housing starts, and manufacturing. All these industries, being large users of base metals, drastically affected the metals industry. US copper companies are still having problems. Reports indicate that many copper employers have cut production, laid-off workers, and permanently closed mines, refineries, and smelters. A decline in the demand for US produced metal products, such as copper, obviously affects some mineral engineering employment opportunities. Other factors to consider when looking at employment opportunities and why it has become difficult for US metal producers to compete in the world market include: • The grades of ore bodies of many US minerals are considerably lower than the grades of ores being mined elsewhere in the world. • The grades of ore bodies currently being mined in the US are steadily declining. • Foreign producers are largely government controlled and are not necessarily subject to the realities of supply and demand. • US environmental regulations have considerably added to production costs. Foreign producers in most countries do not have to worry about these additional costs. • US mines are getting deeper. This adds to the cost of production because of the increasing distance the ore has to be transported. • Plants and equipment are outdated. Many companies find themselves operating with equipment and plants that need modernizing or replacing. This obviously hinders competitive productivity. • Labor and management have had problems. Work stoppages in certain mining businesses and high wage and benefit costs in relation to foreign producers place US producers at a disadvantage. • Much land is unavailable. The US government owns most of the land considered to have the best potential for minerals development. Most of this land is unavailable for mining or exploration. Therefore, it appears that finding employment with a company whose primary business is mining and processing most metals, such as copper, in the US will be quite restricted and competitive. Future Demand It is difficult to anticipate what key employment opportunities within the next few years will be available to mineral engineering graduates. The Engineering Manpower Commission estimated that US engineering schools awarded 72,471 undergraduate degrees in 1983 vs. 66,990 in 1982. This was the eighth consecutive year in which the number of baccalaureates awarded has increased. On a brighter note, the US government's Occupational Outlook Quarterly stated that the growth rate through 1995 for all engineers is an encouraging 49% over present levels. The estimated number of engineers employed in 1982 is 1.2 million. The numerical in-

Jan 2, 1985

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

This report covers the work performed by the Advanced Products Division of FMC Corporation under Bureau of Hines Contract J0155166, Design Evaluation for Development of an Advanced Bolter Module. FMC has evaluated the existing ISMS bolter designs, and the corrections and improvements in progress, including the effect of the three-chain magazine presently being fabricated, and recommends that a complete bolter module featuring a new magazine, safety post and lower stabilizer or similar device be designed, fabricated, and tested, A 29 week program is proposed which includes a four week demonstration. This module would eliminate those reliability problems not presently being solved and would provide a reliable bolter module for a production oriented miner/ bolter.

Jan 1, 1975

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By Manuel Villanueva Bullón

El presente texto describe el proceso de optimización en las operaciones mineras del yacimiento minero San Vicente a través del empleo de las microcomputadoras, las cuales al ser fácilmente transportables, de bajo costo y no requerir de ambientes especiales, permiten brindar in situ con amplitud al soporte que se requiere. Por ello, esta red de microcomputadoras desarrollan sistemas de carácter técnico y administrativo que controlan y retroalimentan información de todas las operaciones, optimizando el control de la producción en la mina y planta concentradora.

Nov 24, 1986

By Valentin Choquenaha Bombilla, Oscar Alvarez Muiloz

"Tintaya’s basic production line is copper concentrate, which has an important gold content. The process used is flotation; the objective of the metallurgical department is to obtain the best results in the copper recovery without neglecting the gold, using very specific reagents. Copper recoveries are considered high, nevertheless every day emphasis is placed upon increasing those recoveries. Regarding gold, optimum recoveries could not be achieved with flotation; and implementation of a gravity circuit was considered.According to microscopy studies, the coarse and very fine grains of gold in native form are lost to tails. The native gold due to its high specific gravity is concentrated at the underflow of the cyclone, remaining in the circulating load of the circuit. It reaches three times the concentration compared to the head grade entering the ball mills. This re-circulation generates very fine and laminated gold particles inside the ball mill, passing to the classification stage making a short circuit to the overflow of the cyclone.The very coarse gold particles as well as the thick flakes of gold do not react favorably to the conventional flotation process; thus studies that have included gravity separation have been conducted to increase the gold recovery. Part of the research included concentrating tables, jigs, and Knelson Concentrators. The Knelson Concentrator proved to be the best selection in terms of metallurgical performance and recoveries considering the throughput and operation conditions of the Tintaya Plant.The gravity concentration circuit with the Knelson Concentrator was commissioned in BHP Tintaya in October 1998, as per the flowsheet shown later on. Presently the global gold production surpasses any estimated expectations.Present efforts are directed towards showing the evaluation and optimization of the different parameters that govern the performance of the Knelson concentrator, as well as illustrating the difficulties and successes throughout the operating period.In the first year of operation 200 tons of gold concentrate have been produced with an average concentrate grade of 320 gramdton, having paid back in full the cost of the automated KC-XD- 48 Knelson Concentrator, the peripheral equipment, and the cost of the installation."

Jan 1, 2002

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By W. E. Hale

The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Programme (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature: during approximately six weeks an orientation survey, involving, geology, geophysical surveying, and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Sto. Nino (Fig. 1). The Sto. Nino study demonstrated (Hale and Govett, 19677 Govett and Hale, 1967) the feasibility of geochemical prospecting relative to other exploration methods for the location and delineation of disseminated copper occurrences, the major source of metal in the expanding mineral industry of the Philippines. A vein occurrence at Suyoc (Fig. 1) was similarly subjected to

Jan 1, 1968

By K Timtner

As shown in former publications there are problems in load sharing of backstops in multiple drives of conveyors. Therefore, detailed calculation methods and design recommendations are required. In this paper various designs of load sharing methods are described and a dynamic torque calculation method will be presented. With this method the loadsharing properties for low and high speed backstops are calculated and compared. These properties depend on the spring characteristic of the drive train between backstop and load. Furthermore, the properties depend on the method of torquearm support and shock absorber configuration. Remarkable differences for external and internal backstops are shown

Jan 1, 1998

By D. Harrington

The mining industry of the United States has-long been severely criticized because of its high rate of accident occurrence, net only as compared with other major industries-in the United States but also with the mining industries of other countries particularly Europe. Statistics (often not of strictly comparable nature) indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These figures are by no means comforting to humanitarian mining men, irrespective of their status in. the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. This picture becomes much darker when the above statistics are augmented with data indicating that. on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar types of mines in Europe, particularly England and Wales, Belgium, France, and Germany. However, these foreign accident statistics should be carefully analyzed before we become very mush concerned about them, because they are clot strictly comparable owing to several considerations, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions axe definitely dissimilar to ours in many if not most phases, and numerous ether factors affect the comparability of foreign mine-accident statistics with ours. Unquestionably it should also be taken into consideration that the accident rate of the 130,000,000 or more constituting the populace of the United. States as a whole is much higher than that of any other major country in the world and is two, throe, or more times the rate of the European countries that have more favorable mine-accident rates than those of the United States. Moreover, it is significant that the mine-accident-severity- rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little mere, favorable than the comparable figures in the United States, namely, that mining-has an accident-severity rate about seven times that of the average of about 30 of the major industries of this country.

Jan 1, 1941

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014