Search Documents

Differentiation of a basaltic (?) magma occurred in an active volcanic area during the late Miocene and Pliocene, and a change in the general mode of extrusion from fissure flow for the basalt to explosion for the andesite reflects an accompanying increasing magmatic viscosity. A caldera formed after the flow phase was completed and was filled with coarse agglomerate, much of which has a fused appearance. After an erosion interval its shape was modified and it became gradually deeper as repeated explosions from growing andesitic volcanoes caused large quantities of pyroclastic material to be deposited. At the close of this phase the floor abruptly collapsed when a, large block of the underlying crust was engulfed. The incompetent pyroclastics filling the caldera steepened in dip and the ensuing fractures were filled by the rising magma as dykes and sills and a chonolith formed below the caldera at a shallow depth. The ensuing activity reveals a further stage in differentiation and biotite is an important new ferromagnesian to be observed in the new rocks.Fracturing of the surrounding basalts was most intense in the rocks forming the periphery of the caldera where steeply and flatly dipping faults resulted from increasing horizontal pressure directed towards the caldera.Further differentiation resulted in the increased crystallization of orthoclase felspar, as evidenced by the numerous intrusives of trachy andesitic composition. Magmatic freezing caused mineralizers to accumulate at the top of the chonolith. These eventually escaped and auriferous pyrites, tellurides, quartz, and calcite were deposited in the surrounding rocks.The flatly dipping fractures are the most important and can be expected at various depths in a zone about 4,000 ft wide surrounding the caldera. Latest movement along these was controlled by magmatic consolidation rather than the shape of the caldera. Some flat faults were able to remain open during mineralization and acted as a feeder for the shallower fractures, thus limiting the depths to which the steeper dipping fractures were mineralized with the possible exception of one particular Nw.-striking lode (the Crown-Crescent).INTRODUCTIONThe gold deposits of the Tavua district were discovered in 1932 and from 1935 to June, 1961, 1,985,041 fine ounces of gold were produced from 4,202,504 tons of ore. Of the original three producers, only the Emperor remains active in the...

Jan 1, 1962

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

The development of Western Mining Corporation's first commercial gold heap leaching operation is described. The laboratory testwork requirements for determining the amenability of ore to heap leaching techniques is discussed. Heap construction and operating practices are described; and production statistics and operating parameters are presented. It is shown that for a specific low grade gold ore a treatment cost optimization can be performed. Taking cognizance of the ore grade, percentage gold recovery, operating costs, and the gold sale price, it can be determined whether Carbon-In-Pulp (C-I-P) or Heap Leaching should be employed as the extraction process. The examples presented in this paper refer specifically to Kambalda and should not be used in themselves as generalities.

Jan 1, 1987

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By D Hunter

A production information management system (PIMS) was recently implemented at Queensland NickelÆs Yabulu Refinery. Although a strong business case was developed to justify the significant investment in PIMS some potential beneficiaries remained sceptical of the anticipated benefits. The decision to install PIMS was justified as the on-line availability of continuous production data enabled the optimisation of some crucial operations resulting in significant cost savings, improved throughput and final product quality. Furthermore the rapid access to extended historical data has allowed the cause of repeated failure of equipment to be determined. The investment is expected to pay for itself within two years and has already contributed towards significant savings. This paper focuses on some of the diverse production improvements gained and compares the anticipated benefits in the business case to those achieved. A brief outline of the phased implementation of the OSIsoft PI data historian and complementary client software at Yabulu is included, along with details of the lessons learned.

Jan 1, 2003

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

By D. Newman

"The U.S. stone industry is in a transition from surface quarries to single and multiple level underground stone mines. The factors driving this transition include surface quarries; ? reaching their economic stripping ratio, ? encroaching on the mineral reserve boundary where the remaining reserves are below the active pit, ? dust, noise, and blast vibration concerns as suburban neighborhoods and development move into formerly rural areas. Ground control is critical to the success of a safe and productive, mining operation. The primary focus of the ground control engineer in an underground stone mine is the stability of the roof or back, development and benched pillar stability, stability of the sill pillar between vertically adjacent mining levels, and floor stability. Roof stability begins with the selection of a stable back horizon based upon the presence of a thin shale parting, stylolite, or other discontinuities from which the production shot can easily ""peel"" away leaving a stable back stratum. Room width and the decision of whether to bolt the roof, the bolt length, bolt type, bolt diameter, and spacing of the support is controlled by the thickness, fracture spacing, jointing, and material properties of the back strata. Horizontal stress controls the header and crosscut azimuth as to avoid driving perpendicular to the maximum horizontal stress direction. Stable pillar dimensions depend upon the interaction of the; ? vertical stress resulting from overburden thickness and multiple level interaction of overlying level(s), ? mining height during development and the final mining height after floor shots are taken while benching, ? presence of faults, folds, or joints passing through the pillar, and ? stone lithology recognizing that the presence of oolitic bands, shale partings, and bentonite beds create zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture sensitive strata, weak stone bands, or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. The ground control issues for underground stone mines are most clearly presented through a series of case histories. The case histories presented in this paper are a mix of ground failures and successful mining. The focus is on the geotechnical data required for underground stone mine ground control for roof, pillar, and floor design and stability analysis."

Jan 1, 2016

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By J W. Glatthaar, M Mavotoi

The occurrence of fluorine in the copper/gold concentrates produced by Ok Tedi Mining Limited has provided a series of challenges to metallurgists since 1988. Although fluorine is distributed throughout the gangue minerals contained within Ok Tedi ores, itsÆ presence in talc and phlogopite (naturally floating fluorosilicates) has proven to be the predominate sources of fluorine in the final concentrate. Initial treatment for the fluorosilicates consisted of the use of a carboxy-methyl cellulose depressant added to the flotation cleaners. This was superceded in 1998 with the installation of a fluorine reverse flotation process for the removal of naturally floating fluorosilicates from the final concentrate when the fluorine content of the final concentrate exceeds smelter-defined trigger points. The fluorine reverse process is similar to by-product molybdenite concentrate production in that sodium hydrosulfide is used to depress copper/gold flotation whilst allowing the fluorosilicates to float. The process was installed in two parallel modules (to match the existing grinding/flotation modules at Ok Tedi), each consisting of a closed rougher/cleaner circuit configuration. Both rougher and cleaner cells are Jameson Cells from MIM Process Technologies, with the selection based on both processing characteristics and available construction space. This paper discusses both the nature of fluorine in-, and its removal from-, Ok Tedi copper/gold concentrates.

Jan 1, 2003

By T van Zyl

Some standards are being used by the corrosion industry on a daily basis. This talk will cover how a standard comes into existence, the different types of standards and the voluntary/ compulsory nature of different standards. The maintenance of standards is discussed This talk also looks at how standards should be referenced, what reference to the mark scheme can be made and which national and international standards might be of value in the corrosion industry.

Jan 1, 2006