Search Documents

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate.

Jan 1, 2003

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Marcia L. Harris

Toxic fumes produced by detonating explosives in surface mining and construction operations pose potential hazards to workers and the public. Blasting operations produce both toxic and nontoxic gaseous products; the toxic products are mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings as well as one fatality. At worst people may be fatally poisoned and the least to be expected is increased public objections to blasting. Local and state agencies could demand a cessation of the blasting requiring more expensive mechanical means to break the rock. This paper discusses the most feasible means of preventing CO migration, mitigating CO that has migrated, and detecting CO in an underground enclosed space and may help reduce the exposure of unsuspecting area residents to carbon monoxide and help prevent the implementation of unnecessary regulations and limitations on blasting. Single-hole shots and small-scale multiple-hole blasts were performed that indicate promising means of prevention and mitigation.

Jan 1, 2008

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By E. M. Williams

The U.S. Bureau of Mines is investigating the use of in-seam seismic methods to monitor stress-induced changes in coal near the working face of longwall mines. Seismic surveys performed through a longwall panel and pillars near the face can provide valuable information on geologic anomalies, high stress regions, tailgate support performance and other conditions that could endanger miners or interrupt production. This paper describes the details of the equipment and data analysis techniques used, and the significant results obtained and their implications for ground control. Using seismic tomography, it is possible to conduct measurements on the pillar and reconstruct an image representing the internal velocity distribution. Successive measurements over several days identify changes in velocity attributable to changes in stress. Several field measurements were conducted at a western U.S. longwall mine to observe stress induced changes within the panel and pillars during mining. A permissible data acquisition system was designed to meet mine safety requirements for operation in gassy air. Certification from the Mine Safety and Health Administration (MSHA) was obtained, and this approved system was used to monitor stress changes in several pillars as the longwall face passed during first panel mining. Tomographic surveys were completed across the longwall panel to map the apparent abutment stresses ahead of mining. Velocity distributions show an increase in vertical stress across the panel from the headgate to the tailgate. Additionally. a yield zone along the face near the tailgate and the forward abutment approximately 100 feet outby the face in the tailgate side of the panel were detected. These results agree well with data obtained from other instrumentation emplaced in the panel near the tailgate. Using velocities for both compressional and shear waves, the Poisson's ratio was calculated for the panel.

Jan 1, 1994

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By Richard J. Mahany, Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 8, 1981

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

The discovery of magmatic nickel sulfide mineralisation within the Musgrave Block of Central Australia, in a region which has received virtually no exploration since the early 1970s, promoted a pegging rush throughout the region and provided a significant boost to the investor interest in resources sector companies. The discovery proved a significant success for the application of generic models for major magmatic nickel-copper sulfide deposits. The entry of junior explorers to the region is the principal mechanism by which the region will be explored, although significant social and physical challenges will impact on the ability of explorers to maintain investor confidence in the region.

Jan 1, 2002

By Sam H. Patterson

Fuller's earth and bentonite are two clay commodities that are interrelated either by mineral composition or use. Because of this interrelation and the sale of both for many different uses, some ambiguity in their classification has resulted. The term "fuller's earth" has no compositional or mineralogical meaning, and it is used more or less as a catchall for any clay or earthy material suitable for certain uses. Most, but not all, of these uses require absorbent properties. Bentonite by geologic definition must have formed from volcanic ash or tuff or the glassy material in volcanic rock; most bentonites consist chiefly of montmorillonite but other clay minerals may be present. In industrial usage the term "bentonite" is applied to any clay consisting chiefly of montmorillonite, irrespective of origin. Georgia and Florida have historically been the leading States in the production of fuller's earth; bentonite has been produced in Alabama on a small scale. The first major use of fuller's earth was in refining of oils. Other materials have replaced fuller's earth for this purpose to a major extent, but many new uses for fuller's earth have been found, and production has increased in recent years. The new uses include absorbent products, insecticide and pesticide carriers, drilling mud, and many others. The bentonite now produced in Alabama is of the "southern," "low selling," or "calcium" type and is used mainly as foundry-sand bond. Most of the fuller's earth mined now is in the Hawthorn Formation of Miocene age; a lesser amount is produced from the Twiggs Clay Member and other beds in the Barnwell Formation of Eocene age. Inactive pits from which fuller's-earth was produced from other formations occur at several localities. The bentonite now mined in Alabama is in beds of Cretaceous age; several years ago bentonite was produced from Eocene beds in this State.

Jan 1, 1972

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By Thomas L. Wright

Exploration activities were maintained at a high level throughout 1966. Numerous significant discoveries and developments in which geologists played an important part were announced. Although the complete results of exploration activities carried out during the year by private companies have not been announced, the following are among the more important developments that have been made public knowledge. In the western states, exploration for practically all of the metals continued at a high rate. Substantially increased interest in uranium occurred this year, and it is felt by many that a real boom in the demand for uranium may come about in the near future. The reasons have been the more rapid acceptance of atomic power than had been anticipated, and that uranium producers can now sell their product to private interests and even foreign countries. A tremendous demand for uranium is anticipated by many, and this has rekindled exploration activity. On the Colorado Plateau, in Wyoming, and in the area around Grants, N. M., a number of companies have undertaken uranium exploration programs, among which are Kerr-McGee, Homestake, Anaconda and Utah Construction. A new uranium orebody in Texas was brought into production early in 1966 by Susquehanna Western.

Jan 2, 1967

By W. J. Wuest

This U.S. Bureau of Mines report presents an overview of ground control considerations associated with cutter roof failure. Many of the relevant U.S. and international research studies since the late 1940's are reviewed, and summaries of recent design guides are included. Factors affecting cutter roof, such as underground stress field and rock structure around the entry, are described. Strata control techniques are also outlined. These techniques are divided into three sections: artificial support, mine structure design, and multiple-seam extraction. Other subjects covered in the report include monitoring and prediction, effect of geologic features, and mapping of adverse mining conditions. The emphasis of this report is on practical considerations; theoretical discussions are minimal.

Jan 1, 1994

By A. W. Hahn

USE of gold leaf goes back to biblical and even to prehistoric times. Both gold and silver, as well as other metals, were employed in illustrating or illuminating manuscripts. The medieval monks also used bronze powders. Metals were subdivided as finely as possible by mechanical methods, or by granulation and then were pounded into finely divided flakes. Substances such as honey have also been employed, since early times to keep the flakes of metal apart during grinding. Stearic acid is a more modern agent used in flaking aluminum and other metals. Finely divided "blue powder" is a by-product in retorting zinc ores, and contains from 78 to 90 per cent of zinc metal. This has been used as a precipitant for precious metals in the cyanide process and for chemical reduction processes. The making of zinc dust by atomizing is a step well known in electrolytic zinc plants. The Thermit process of Goldschmidt also requires the use of finely divided aluminum.

Jan 1, 1937