Search Documents

By Ernesto Maldonado, Zach Agioutantis, Jesus Romero

Reliable prediction of dynamic deformations is important when planning to undermine important structures that cannot tolerate large relative deformations and or large horizontal strains. This paper presents examples of dynamic deformation profiles that include subsidence, horizontal displacements, and horizontal strain for a number of points over a retreating longwall panel in the eastern United States. The prediction points are located at different distances from the excavation rib and therefore present a different response in terms of dynamic movements. The formulation is based on the influence function method as implemented in the Surface Deformation Prediction System (SDPS). Results show that the subsidence development curve may be reliably predicted for surface points in the middle of the panel. However, in cases where points may be affected by the magnitude of the edge effect offset, subsidence predictions may be very conservative, that is, higher than actual movements.

Jul 1, 2023

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Dolea Gabriel Gheorghe

In the present paperwork is proposed an economical-mathematical model (fuzzy) that aims optimize the technological variants of the mechanized coal face. By fuzzification, the issues to solve become more flexible and allow the decision maker to acquire more variants for the functions objectively established. The description of technological solutions is carried out by a set of controllable variables of "category" type by which the type of the machinery is defined within the frame of the actual geological & mining conditions. In the paperwork are used concepts of "successions graph" and "matrix of compatibilities"; with their help a methodology to choose between different technological variants of coalfaces is proposed. It treats the problem of developing the functions that express the membership degree in vague concept. In the end it is presented an assessment procedure for the technological variants of mechanized coal face.

Oct 1, 2009

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By W J. Haylock, K Wasiel

PX4 Software Pty Ltd is a Brisbane-based company, which specialises in providing tenement management software to mining and exploration teams operating in Australia and several international jurisdictions, including the United States, Africa, and Canada. Whilst the company is experiencing substantial growth due to a demand from both the minerals and mining technology sector, there is a crucial gap in the market for critical minerals, which will be required to achieve the net-zero emissions goal set by the Paris Agreement for 2050. To help understand and address the technology gap identified by the unprecedented demand, PX4 Software undertook the Annual Survey of Technological Transformation in the Exploration Industry. This survey involved interviews with 12 very distinguished subject matter experts in the fields of Geoscience and Geology from across the globe. From this survey, we have defined eight major categories of exploration technologies. Notably, the most transformative of these technologies over the past 65 years falls into the Geophysical Methodology category, specifically focusing on image and signal processing of both airborne and downhole data. Advances in computing power during this period have significantly improved data processing quality, enhancing orebody modelling, and targeting. This has had a profound impact on the industry. Moreover, the survey reveals that future transformative technologies are expected to centre on the automation of existing processes through AI and Machine Learning techniques. This is expected to help facilitate the identification of critical mineral systems and thus enable the exploration industry to make more informed decisions based on data analysis using Machine Learning and AI.

Sep 1, 2024

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

Jan 1, 2005

The overall objective of this study is to gather operational data from selected surface coal mining systems in the United States, and to assess the potential production and economic capacity of the systems. The study includes: four mines, each using a different mining technique and different equipment. One mine was selected from each of the major coal fields: Midwestern, eastern,, northwestern, and southwestern. The Midwestern Mine is located in the Central Plains and produced 1.45 million tons of raw coal during the study year The Midwestern Mine uses the area mining or box-cut technique. A large in-pit shovel and a bucket wheel excavator are used to remove the overburden. Coal is removed by a loading shovel and transported to the dumping point by large off--highway trucks.

Jan 1, 1975

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

By G. G. Roy, R Shekhar

Pachuca tanks are extensively used for the cyanide leaching of gold and the carbonate leaching of uranium, processes in which oxygen mass transfer plays a very important role. Experiments were carried out to clarify the effect of design and operating parameters on oxygen mass transfer. Parameters such as the ratio of tank height to tank diameter, the ratio of draught-tube diameter to tank diameter and the tank design were found not to influence oxygen mass transfer. Results also showed that equal superficial gas velocities may be used as a criterion for scaling up oxygen mass transfer in both full-centre-column and free-air-lift Pachuca tanks with clear water. A volume-averaged, volumetric gas-liquid mass-transfer coefficient (k'av) was used to characterise oxygen mass transfer in full-centre-column tanks. The axial dispersion model was used to determine k'av. The resulting model used only tank geometry and air flow rate as inputs for the prediction of k'av in industrial-scale tanks. Predictions from the model show clearly that "local" mass-transfer coefficients, measured at one or two locations, may not adequately represent gas-liquid mass transfer in industrial tanks. It is therefore necessary to obtain an estimate of k'av

Jun 18, 1905

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

By M. Gericke

The microbial leaching of metal sulfides is now an established biotechnological technology. Over the past 25 years, refinements in the engineering design of bioleaching processes have paralleled advances in our understanding of the diversity and role of the micro-organisms driving the process and the mechanisms by which micro-organisms enhance metal sulfide oxidation. Commercial success started with the treatment of refractory gold concentrates using mesophilic micro-organisms, followed by the development of tank bioleaching processes for the treatment of base metal concentrates. This was, initially, a mesophilic process with limited potential for recovery of copper from chalcopyrite concentrates due to slow rates and low copper extractions. The exploitation of thermophiles represents a major breakthrough in the development of bioleaching technology for the treatment of chalcopyrite-containing ores and concentrates. This development also opened the route to heap bioleaching of chalcopyrite ores, which is now a major focus of research programmes and piloting campaigns. This paper reviews the historical development of minerals bioleaching processes and gives an update on the current status of commercial tank and heap bioleach operations around the world.

Jan 1, 2009

By R. G. Votteler, A. C. Brent

"The business performance of mining corporations in South Africa is adversely affected by the constantly increasing electricity costs. The most commonly used power sources are the national utility supplier via a grid connection, and on-site diesel generators. Previous research has identified the renewable sources of solar photovoltaic (PV), onshore wind, and geothermal energy in hybrid versions with current sources as possible opportunities to counteract rising electricity costs. To provide a clear understanding of the new, developing market of renewable energy sources, this research is divided into two papers. This first paper investigates the internal business structure of mining corporations in order to evaluate electricity generating sources. The multi-criteria decision analysis (MCDA) method is selected as the most suitable approach for this. The paper identifies the criteria used by mining corporations to evaluate possible electricity generation sources for self-generation by means of the corporations’ own investment. Four mining corporations with several mining locations were interviewed. The interviews revealed both new and identical evaluation criteria when the findings were compared to earlier MCDA adaptations analysed in the literature review. The second paper (Part 2) combines current knowledge about the external macroeconomic environment with the findings about the internal environment described here. MCDA is adapted in Part 2 and implemented to analyse and compare current to hybrid renewable sources from the perspective of mines. IntroductionMining corporations in South Africa are currently adversely affected by increasing electricity prices. Electricity is supplied mainly by Eskom1 and, especially in remote locations, by on-site diesel generators (Boyse et al., 2014). Electricity price increases, emanating from diesel price hikes and Eskom, have escalated the total operational expenditure on electricity by the largest mining corporations from 8% to 20% of total operating costs in the past seven years (EIUG, 2015). The reliability of electricity supplied by Eskom has decreased drastically (Govender, 2008), and the prices will increase annually by at least 13% until 2018 (Numbi et al., 2014; Eskom, 2015b). In addition, the South African government plans to introduce a carbon tax on greenhouse gas emissions (Alton et al., 2014)."

Jan 1, 2017

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

General Aurelio Blanquet,* the best known of living Mexican soldiers, formerly the trusted friend of Porfirio Diaz and organizer of the old Federal Guard of Mexico City, who as a sergeant commanded the squad that executed sentence on Emperor Maximilian, and. more recently was Minister of War in the Cabinet of Victoriano Huerta, landed in Mexico early in April and joined the forces of Felix Diaz. His landing in the state of Vera Cruz, it was stated, was for the definite purpose of aiding the movement now under way to overthrow Venustiano Carranza and to place in power a government that will be "pro-Ally" in its sympathies and will promulgate and enforce laws that will guarantee the rights of life and property in Mexico. The New York Tinges says of the revolution editorially: "Whatever may be the success of General Aurelio Blanquet's attempt to overthrow the Carranza Government in Mexico, admiration cannot be withheld from the General's publicity manager. No enterprise awning at the overthrow of a Government ever had more favorable and widespread advertising. Felix Diaz, whom Blanquet is going to reinforce, supersede, or overthrow, as the case may be-Mexican precedent in these matters offers opportunity for considerable speculation-has been conducting his revolution, at the old stand for some time, but without much success. But, says General Blanquet's representative, the landing of Blanquet will send a thrill to the heart of every true republican.' Meanwhile a biographical booklet is published, adorned with photo¬graphs illustrating the General's record, including such varied matters as the General in favor, receiving a decoration from Victoriano Huerta, and the General in exile, feeding the birds in Central Park."

Jan 5, 1919

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917

By Frank Gilbreth

THE problem, of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community, without placing the cripples into competition with any existing class of workers.

Jan 4, 1918