Search Documents

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By MOHAMMAD R. H. GORAKHKI, CHRISTOPHER BAREITHER, MANUEL APARICIO, IV JOSEPH SCALIA

Comingling filtered tailings and waste rock in a tailingsdominated mixture is a mine waste management strategy that has the potential to create geotechnically and geochemically stable landforms. Potentially acid-generating (PAG) waste rock can be sequestered within a filtered tailings matrix to enhance water retention and decrease hydraulic conductivity relative to a waste rock pile, potentially minimizing acid rock drainage (ARD). Enhanced water retention can reduce oxygen ingress limiting oxidation and resultant acid generation. Reduced hydraulic conductivity can slow inward percolation and outward drainage. In dry climates, the tailings matrix can hold precipitation near the ground surface accessible to evaporation and transpiration, thereby decreasing percolation. This paper presents an evaluation of comingled filtered tailings and waste rock in a tailings-dominated mixture (termed GeoWaste herein) and illustrates that ARD can be reduced under field conditions in a subtropical–highland climate.

By R Tooher, S J. Oliver

The operation of copper flotation circuit is a challenging task for the site metallurgists and plant operators. To optimise the performance requires meeting both grade and recovery objectives. These plants have numerous pieces of equipment that are monitored by hundreds of sensors. The challenge is to review these sensors and adjust the numerous control inputs to maintain peak operational efficiency for extended periods. There is also a need to respond to equipment failure. These challenges lead to in operational inefficiencies and can result in a reduction in revenue.This paper details an overview of an operational assistance tool implemented at Newcrest's Telfer plant’s copper flotation circuit. This tool is based on a digital twin of the plant. A digital twin is a model of the plant that is simulated in parallel to the normal plant operation. It is fed with the plant data in real time to provide a prediction of plant operation. The model outputs directly generate the metrics that are used to assess the plant performance, and these are compared with the metrics calculated from the actual plant’s operation. Deviations between the model estimate and the plant’s actual performance are used to gather insight into plant health and alert the operator to poor performance. The operators gather more information regarding the root cause by reviewing the model’s inputs that have deviated outside their normal operating range. An evaluation of the plant performance, following the commissioning of the digital twin, showed an overall reduction of acid soluble copper in the tails.This paper discusses the implementation of a digital twin of the plant to monitor plant performance during live operation. It will include details on data collection and cleansing, data reduction techniques, model development, and real-time implementation. The results of the case study of an implementation of a digital twin at Newcrest's Telfer copper flotation plant will be used throughout the paper.CITATION:Oliver, S J and Tooher, R, 2018. Optimising flotation plant operation by using a digital twin in the control room, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

In this U.S. Bureau of Mines report, two drill-split mechanical excavation mining system concepts are described, casted, and cost compared with conventional drill-blast mining systems. The concepts for the two drill-split mechanical excavation mining systems presented are (1) a method for steeply dipping narrow veins 0.6 to 1.2 m wide and (2) a longwall method for fiat-lying tabular ores. In the proposed systems, 70 to 80 pet of the ore is disposed of underground as backfill. For sortable ores, face area crushing, sorting, and direct stowage of run-of-mine waste and low-grade ores are proposed. The underground sorting and stowing of waste reduce materials handling, processing, and waste disposal costs by reducing the quality of ore transported to the surface by 70 to 80 pet (by volume). Because many of the tools and techniques proposed for use in these systems have little or no historical mining industry use, cost assignations are heavily influenced by engineering judgments and presented as prefeasibility-level cost estimates. These estimates, presented as discounted-cash-flow-rate-of-return (DCFROR) values, show the proposed systems to be at least as profitable as, and in some cases 50 pet more profitable than, conventional drill-blast mining.

Jan 1, 1994

By M. Deutsch, E. González, M. Williams

"There is uncertainty in ultimate pit limits due to geologic variation and unpredictable economic landscapes. In this work we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis is used to model the effects of geologic and economic variation on ultimate pit limits and overall project economics. This analysis is made possible by a new, highly efficient pit optimization implementation which can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement, and to mitigate the possibility of incurring substantial costs relocating critical mine facilities. INTRODUCTION The mining industry is increasingly concerned with the effects of risk and uncertainty. Uncertain prices, unpredictable global markets, and unknown foreign exchange rates can alter the economic viability of a mining project in substantial ways. This economic uncertainty is compounded by geologic uncertainty. The extent and quality of any given deposit cannot be fully measured and is not known before consequential decisions must be made. These two sources of uncertainty are responsible for the majority of deviation between what happens during operation and what was initially planned. Understanding and explicitly quantifying this uncertainty will lead to better decision making and allow mining engineers and investors to be aware of what may occur. It is unrealistic to believe that one model, estimated from sparse measurements, is enough to capture both geologic and economic uncertainty and allow for optimal decisions. The entire breadth of uncertainty should be considered, as both upside and downside risks have large impacts on the investment potential and operational efficiency of mining projects. The workflow presented here uses Monte Carlo simulation and parametric analysis together to explicitly analyze the breadth of geologic and economic uncertainty as it applies to ultimate pit calculation and long range mine planning."

Jan 1, 2015

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979

I attended a funeral in West Monroe, Louisiana, for one of the best powder peddlers I’ve ever known. He started work in 1948 for Dixie Dynamite, a seismograph explosive distributor. His first job was as a truck driver, then magazine keeper and then sales re p re s e n t a t i v e . When Dixie Dynamite quit, he acted as an explosives sales agent for sometime before moving on to Kansas to be a sales rep for a distributor there. We called him the “ragin cajun” long before James Carville came on the national scene messing up things. While he was born in G e o rgia, he was a Cajun at heart. I don’t believe the old saying, “Build a better mousetrap and the world will beat a path to your door.” To me, the best products in the world need to be sold. Two examples of this are the Beta system for TV and the Apple Macintosh computers. Beta is the best system but VHS took over because the Beta people fell down on the selling job. Windows 98 is Macintosh ‘86 but again the engineers were not salesmen. Marion “Johnny” Johnson who was buried only about a half mile from his first magazine site proved that good selling is good citizenship. He could have sold any firstclass product, for he wouldn’t tolerate inferior items, and made a successful career of it, but he chose dynamite and the industry benefited from his talents.

Jan 1, 2004

The Department of Mineral Resources is the lead agency in mine site environment management and control in New South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.

Jan 1, 1995

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

By George H. C. Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable apparatus, which can rapidly give a sufficiently reliable indication of the relative dust hazard. HISTORY OF DUST DETERMINATION IN ONTARIO The first record of mine-dust determination in Ontario is given in an article by Dr. J. H. Elliott,' in which he records a few dust counts made with the Palmer spray apparatus. There were insufficient data from which to draw any definite conclusions or reasonably compare with present-day counts using the konimeter. The first konimeter dust sampling was started in the Porcupine district in 1926, using light-field counting without adhesive and with no sample treatment before counting. A method of semidark-field counting was used from about 1928 to 1931 and dark-field illumination was adopted permanently about December 1931. The konimeter has been continued as the principal means of dust sampling in the mines of Ontario, where South African practice has been adopted because in South Africa most careful study has been given the problem of silicosis, and very complete records of work done there are

Jan 1, 1937

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By Charles D. Litton

Introduction The successful performance of a mine-wide fire detection system depends upon its ability to detect the presence of a fire rapidly and reliably. It should be sufficiently rapid so that there remains enough time to either safely evacuate a mine or successfully extinguish and control the fire or both. It should be reliable so that false alarms are minimized without sacrificing sensitivity or time response. Systems should also be durable enough to withstand the mine environment over long periods of time while maintaining a high degree of re1iability. Maintenance and calibration of the system should be simp1 e and not require the expenditure of excessive time and manpower to keep it operational. Sensitivity, reliability, and durability of mine fire sensors and their electronic support systems have been the subject of significant Bureau research within recent years. The bulk of this type of information, along with the reports from which the remainder of this paper is derived, can be found in the Bibliography. It suffices to say that there exist commercially available systems for use in mines. This paper addresses a strategy for the use of such sensors and systems. Many factors influence the design of a mine-wide fire detection system, such as the potential sources and modes of ignition, the types of combustibles involved and the quantities avai1able for fire growth and flame spread. Mine air ventilation influences the growth and spread of a fire and also serves to transport the products-of-combustion to other areas of a mine remote from the fire. Fire sensor alarm thresholds place limits on the sizes of fires that can be detected. The time to respond to a detected fire, either in terms of evacuation or control and extinguishment, place additional time constraints on the design of fire detection systems. These factors interact with each other, often in complex ways, and it is the definition and understanding of these factors and their interactions that hold the key to the design of adequate and re1iable fire detection systems. Our level of understanding of the problem has increased dramatically within recent years and it is the intent of this paper to discuss the progress that has been made and how the information can best be used to improve the level of fire detection in underground mines.

Jan 1, 1986

By Sukumar Bandopadhyay

The Marine Minerals Technology Center (MMTC) was authorized by an act of the United States Congress in 1996. The act established several marine minerals research centers in the U.S., including one at the University of Alaska Fairbanks. The Alaska MMTC is funded through the Minerals Management Service of the Department of the Interior and concentrates its research in the Arctic seas region. Recent research projects at the MMTC include, among others, application of a geographic information system (GIS) to the gold placer deposits offshore Nome, Alaska, development of a marine gold placer reserve definition model using a neural network, and development of an expert system model for submarine tailings disposal (STD) planning and decision-making. Although geostatistics remains the most prevalent method used today for ore grade estimation, researchers have made numerous improvements over the years for accurately predicting grades of ore using other estimation techniques. One such technique, the neural network, has recently emerged as an alternative to geostatistics for grade estimation purposes. A neural network is a non-linear, model-free estimator that is well-suited for noisy and/or sparse data environments. Neural networks perform best with non-linear spatial data, contrary to the stationary assumption of ordinary Kriging techniques. In the marine placer ore reserve definition model, the neural network technique was used to estimate placer gold reserves offshore Nome. This study demonstrated the utility of neural network modeling over other traditional ore reserve estimation methods, especially for high cut-off grades. Some of the relevant issues of neural network modeling were also addressed in the study. In testing, the neural network produced results that were close to those from geostatistical techniques including Kriging, polygonal, and inverse distance methods.

Jan 1, 2005

By S. E. Restrepo

In recent years, mining operations have experienced the impacts of climate variability, increasing costs, and changes in the socioenvironmental dynamics of the territories. For this reason, the aggregates industry needs to design and define concrete and immediate actions to address climate change. An appropriate way to achieve this is as follows: • Calculate greenhouse gas emissions, sources, and relevance factor. • Make projections of future scenarios. • Design and implement action plans The proposed climate change mitigation and adaptation projects are logistical optimizations of mining equipment (mitigation). Second is the design of an early warning system to predict possible flooding (adaptation).

Mar 2, 2022

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

By N. Arbiter

The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter ratio. This is in spite of the fact that practice varies substantially in this area: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia; historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to/the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills; on the occurrence of the overload phenomenon; and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape face or is of major importance in this area; and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type.

Jan 1, 1990