Search Documents

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By M. Pawlik, E. Arinaitwe, V. Ferrera

A series of flocculation tests were performed on dilute quartz suspensions with the use of five polyacrylamide-based flocculants of similar molecular weights but of different degrees of anionicity. The tests were performed as a function of ionic strength and pH. The macromolecular conformation of flocculants in solution was assessed through intrinsic viscosity measurements under the same physicochemical conditions as those of the flocculation tests. It was generally found that the flocculating efficiency of the polyacrylamides correlated with their ability to coil or stretch in solution. Polyacrylamides with the degrees of anionicity on the order of 10-18% showed the highest flocculating efficiency in terms of the settling rates of the flocculated solids and the residual turbidity of the resulting supernatant. At the same time, these most effective flocculants were also found to exhibit the greatest tendency to coil and stretch in solution. This result suggests that the flocculating power of a flocculant is determined not only by its ability to adsorb onto (and bridge) fine particles but also on its ability to conform to the size of the resulting floes.

Jan 1, 2009

By K. P. Wright

THREE OF the gold mines in the Red Lake Camp operates fluid bed roasters in their milling circuits. The mines are Campbell Red Lake, Cochenour Willans, and Dickenson. The roasters are used for the autogenous roasting of a flotation concentrate for subsequent gold recovery by cyanidation. Cochenour and Dickenson operate single stage reactors, whilst Campbell use a two-stage system. Ore treated by the mines is similar in that the major part of the gold is associated with arsenopyrite. Other sulphides present are pyrite, pyrrhotite, stibnite and sphalerite. Gangue minerals are mainly quartz, with carbonates and talc. Mineralization is, for the most part, extremely fine, and there is intimate association between sulphides and quartz, so much so, th at a picked specimen of apparently massive arsenopyrite will frequently contain as much as 80 per cent gangue. Gold recovery by straight cyanidation on this type of ore would not be higher than 80 per cent and

Jan 1, 1961

AS I told you in the chapter on salts, saltpeter is a mixture composed of many substances extracted with fire- and water from arid and manurial soils, from that growth which exudes from new walls or from that loosened soil that is found in tombs or uninhabited caves where the rain cannot enter. It is my belief that it is engendered in these soils from an airy moisture that is drunk in and absorbed by the earthy dryness. Considering its effects, I do not know how to decide and say exactly what the nature of saltpeter is. The learned and very wise physicians find it salty and with a subtle sharpness both in taste and in their medical experiments. Considering its strong biting qualities, they decide to say that it is of a hot and dry nature; on the other hand when they see that it is engendered from the air and that when touched by fire it becomes inflammable and vaporous, and rises with a fearful impetus when mixed in powder for military guns, it manifestly shows itself to be of a hot and moist airy nature. And then when they see that it is shining and transparent with whiteness and is fusible in every fire in a manner corresponding to a thing of a watery nature, and since it. is heavy, it seems that it can be said to be watery in nature. To this is added the experience of touch and of the great cooling action which it has on water in summertime when wine is to be cooled, and since it crushes and breaks with but little pressure, it might be thought to be earthy in nature; especially when it is seen to change into a hard, white stone when burned with an equal amount of sulphur. Thus it seems that every one of the elemental qualities is predominant in it. Now the ancients called this, or a similar thing, nitrum. [150] Pliny, in Book XXXI of his Natural History, has said that it was a thing not much different from salt, that doctors do not seem to have yet known its nature, that it is found in various places, and that the best is found in Macedonia. But among the moderns and especially in our regions, it is not known today what it is that Pliny and other writers refer -to, since according to the aforesaid Pliny and other ancient writers it is a natural mineral. Some say that in place of, the natural kind the artificial will serve for the same medicinal purposes, since it has the same nature and is perhaps more powerful.

Jan 1, 1942

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By W. Joseph Schlitt

The use of plate and frame filter presses for dewatering cement copper at Kennecott' s Bingham Canyon precipitation plant is described. The dewatering process begins by periodically flushing a dilute copper slurry from cone precipitators to a rake thickener. The thickener underflows intermittently to an agitated surge tank which feeds the filter presses with a relatively constant slurry containing 10 to 20% solids. The presses operate with a three-stage cycle; loading, air blowing and discharging. Exothermic reactions occur during the air blow which cause actual drying as well as promoting dewatering via simple filtration. At the completion of the air blow, the presses are discharged onto a conveyor belt which transfers material to the load-out building for shipment to the smelter. An extended investigation was undertaken to relate moisture content in the filter cake to maximum press temperature, acidification of press feed, percent solids in the feed, and percent insol in the copper. Of these, press tempera¬ture and feed pH (3. 5 to 1. 0) have the greatest impact on drying. Because the discharged filter cake is hot and continues to undergo exothermic oxidation, significant drying occurs during subsequent handling so that a product containing 8 to 14% moisture is delivered to the smelter.

Jan 1, 1977

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By Jennifer B. Leinart

With the signing of the North American Free Trade Agreement (NAFTA), Canada, the United States and Mexico entered into an international experiment in economics amid a cloud of controversy that still lingers. Central to the controversy are the disparities in wages that exist among workers in the signing countries. Wage surveys completed by Western Mine Engineering show the degree of disparity that exists among the mining industries of those three countries. Labor costs constitute 30% to 50% of operating costs. So these wage differences are a matter of interest to the mining industry. It is unclear how much of a factor they are in determining where companies search for and develop new mines. That depends on where minable deposits are expected to be found. However, a deposit that may not be minable in the United States or Canada may be minable in Mexico because of lower labor costs. Some adjustments are anticipated for the Mexican mining industry if and when its wages begin to approach comparability with US and Canadian wages. Table 1 combines the results of four recent surveys. It lists benchmark wages for mining job titles common to all the countries. About 220 mines are covered by the combined surveys. Canadian miners' wages, converted to US dollars, are typically 75% to 95% of US wages, while Mexican miners' wages are less than 10% of those in the United States. Table 1 also shows that wage disparities are not confined to international borders. In fact, the difference in average wages between the US coal industry and the US metal and industrial mineral industries is greater than between the Canadian and the US mining industries overall. Table 2 shows that managerial, technical and administrative salaries show similar, but less pronounced differences among the three countries. Salaried personnel at Canadian mines earn 80% to 90% as much as their US counterparts, while those in Mexico earn 20% to 30% as much. Here again, average US coal salaries exceed average salaries for the US metal and industrial mineral industries.

Jan 1, 1998

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide. application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and. establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By G Maude, R Ayres, R N McLean, N A. Reynolds

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mabilo copper-gold-magnetite skarn deposit is located in southern Luzon in the Paracale mineral district, where iron has been produced historically from several skarn deposits. Mabilo occurs in the south-west of the district and is distinct and significant because of its high grades of copper and gold compared to historical mines.The Mabilo licence surrounds the Venida prospect, where past small-scale mining has exploited iron, copper and gold mineralisation in oxidised skarn. A ground magnetic survey in 2007 defined a number of strong anomalies under Quaternary volcanic cover south of Venida. The property was acquired by Sierra Mining Ltd in 2011, the magnetic data were remodelled and drilling commenced in September 2012. Diamond drill hole MDH001 targeted the strongest anomaly, which was 500 m south of Venida and under 20 m of volcanic cover. It intersected 94 m with an average grade of 2.2 per cent copper, 1.6 g/t gold and 36.6 per cent iron. Subsequent drilling was targeted by magnetic modelling, incorporating magnetic susceptibility data from drill core, which resulted in a high percentage of successful drill holes.The mineralised skarn preferentially replaces a dipping limestone unit within an Eocene sequence dominated by volcanic siltstone and sandstone, metamorphosed to marble and hornfels in the aureole of a Miocene quartz-diorite intrusion. Skarn occurs discontinuously along the eastern and southern diorite contact, controlled by primary sedimentary facies variation, structural geometry, fault offsets and intrusive contacts.Coarse magnetite skarn with garnet and minor wollastonite and clinopyroxene contains variably abundant chalcopyrite and minor molybdenite. Magnetite skarn occurs in sharp contact with unaltered marble or grades into garnet skarn with minor chalcopyrite. Structurally controlled retrograde skarn alteration is strong to intense and is characterised by bornite, clinozoisite, iron carbonate and chlorite. The retrograde skarn is weakly overprinted by late-stage pyrite veining and brecciation associated with clay-silica alteration with arsenopyrite and tetrahedrite-tennantite.The quartz-diorite stock is interpreted as the source of the prograde skarn-forming and mineralising fluids. Late-stage porphyritic intrusions in the contact zone indicate continuing magmatism during uplift, when telescoping led to a high-level, high-sulfidation overprint. This suggests the potential for deeper porphyry-style mineralisation.CITATION:Reynolds, N A, Ayres, R, McLean, R N and Maude, G, 2015. The Mabilo copper-gold-iron deposit – a new skarn discovery in the Philippines , in Proceedings PACRIM 2015 Congress, pp 431–438 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S. H. Ash

THE MAGNITUDE of the drainage problem of the anthracite industry in Pennsylvania's Western Middle field is realized when it is known that in 1951 nine pumping plants in this field pumped nearly 36 billion gallons of water to the surface. This is almost 68,000 gallons per minute pumped against an average hydrostatic head of 350 feet for that year alone. In 1948 over 20,000 gallons per minute was pumped by relay pumps against an average hydrostatic head of 265 feet. In addition to the water pumped to the surface, it is estimated that 15,000 gallons per minute overflows to the surface from underground pools in idle mines. The volume (second-feet) of water pumped and overflow water is almost 1;z times the, average mean flow of the Schuylkill River at Pottsville for the 8-year period 1944--51 (7, 13).4 Mahanov and Shamokin Creeks drain an area of 99 square miles in the Western Middle field, and all surface drainage in this area must traverse some part, of the coal measures before entering these streams. On the basis of 46.03 inches of rainfall (the weighted average of 6 recording stations for 1948), the runoff from the drainage area during that period was 51 billion gallons, approximately 1 times the volume of water pumped by all mine-pumping plants in the Western Middle field. In other words, because of the pervious strata overlying the mine workings, approximately two-thirds of the total runoff in the drainage, area becomes mine water tributary to the pumping plants.

Jan 1, 1953

By A. A. Ruitenberg, G. Ruitenberg, J. Chandra

"The Caledonian Belt is mainly underlain by Late Precambrian and possibly Early Palaeozoic rocks, which are in part overlain by younger strata. Most of these rocks are weakly deformed, except for those in some linear . zones, which have been intensely deformed by cataclasis. Mineral deposits related to two distinct metallization episodes have been recognized. The earliest are zinccopper- lead sulphide deposits, which have been concentrated in the axial regions of late-stage cross-folds within the main cataclastic zone. The host rocks are andesitic and dacitic tuffs which show effects of intense talcose alteration, silicification and chloritization. Deposits related to the second episode are mainly composed of copper sulphides with locally abundant tennantite and tetrahedrite, which occur in brecciated and fractured carbonate-quartz veins. These veins postdate the late-stage cross-folds. VLF-EM and high-sensitivity magnetics proved to be very effective in delineating the geology of these deposits."

Jan 1, 1972

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Fred R. Ingram

FOR the purpose of this discussion, let us consider that the Rocky Mountain region covers the area in the seven Mountain States, Idaho, Montana, Wyoming, Utah, Colorado, New Mexico, and Arizona, and before we discuss the needs of these states, let us define Industrial Hygiene. Industrial Hygiene is that branch of preventive medicine concerned with the protection of health, improvement of efficiency, and prolongation of life of the industrial worker; in short, adult health conservation. It includes in its broad meaning not only the prevention of occupational diseases, such as silicosis, lead poisoning, cadmium poisoning, and many others, but such relative problems as overcrowding, fatigue, and personal and mental hygiene; exposure to abnormal temperatures, pressures, and humidities; ventilation, heating, and lighting. It is a science which requires the combined activity of medical personnel (doctors and nurses), engineers, and chemists to evaluate the exposures and determine the means of eliminating the hazard. The engineer surveys the workplace, takes air samples at the breathing level of the workman, and analyzes the work exposure. The chemist determines in his laboratory the exact amount of toxic material collected in the sample, which represents the exposure of the workman. The doctor must diagnose the occupational disease, recognize its cause, and evaluate the disability. Together, all three must correlate the data obtained and devise efficient methods, medical or engineering or process changes, for controlling or minimizing the dangerous condition and for studying the effectiveness of these measures. The plant doctor, in addition, must aid in the readjustment of the incapacitated worker and provide facilities for prevention. Industrial hygiene, however, is of no avail without the understanding co-operation of management.

Jan 1, 1945

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010