Search Documents

The New South Wales coal industry is a highly mechanised well organised industry which has developed from an annual production of slightly less than 13 million tons in 1950 to over 33 million tons in 1969. Although continuous miners were not introduced into the mines until 1950, by Jillle 1969 the percentage of coal won by these units was 87.3. The paper describes mining conditions in the various coalfields of the State, their complexities and problems and how these have been dealt with. The introduction of fully mechanised long wall faces has presented a challenge which has been accepted and descriptions of systems in use are discussed. Major expansion of the industry is anticipated to meet the requirements of the growing Australian steel industry, for local power generation and to meet the increasing demands of overseas markets.

Jan 1, 1971

Lack of selectivity in mixed mineral flocculation can be attributed to one or more of the following factors: dissolved ion interference, heterocoagulation, mechanical entrapment in flocs and entrainment of fines between flocs. In a study of apatite- dolomite system, it was determined that dissolved ions do not have a significant effect on selectivity. Heterocoagulation was minimized by choosing proper process conditions and addition of a dispersant. Mechanical entrapment was proved to be insignificant and efforts were made to reduce entrainment by choosing an appropriate method of separation of flocs from fines. A new factor termed "polymer induced entrapment" which occurs due to limited affinity of the polymer to the mineral which is not flocculated is postulated to be the cause for the loss of selectivity.

Jan 1, 1986

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By M. Lindgren, M. Latva-Kokko

Process performance can be significantly influenced by proper design of hydrometallurgical reactors. Optimal reactor configuration is case specific and depends on process requirements such as reaction rate limiting factor and particle size distribution. Choice of materials and manufacturing methods also play important roles in highly corrosive and abrasive environment often involved in hydrometallurgical industry. In this paper performance of different reactor designs has been compared in some typical hydrometallurgical applications. Results show that significant improvement in energy consumption, gas utilization efficiency and equipment lifetime can be achieved with process specific reactor design.

Jan 1, 2014

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By R. R. Sayers

SILICOSIS is a term known to almost everyone today. Yet, in spite of a great deal of study, much is still to be learned regarding the disease. Government organizations are still continuing their investigations, begun near Joplin, Mo., 25 years ago. Work is also being done in several universities, as Harvard, Pennsylvania, Rochester, and Toronto, and at least two private organizations, the Air Hygiene Foundation of America, Inc., and the Saranac Laboratories for the Study of Tuberculosis, devote most of their time to this subject. Similar studies have been and are being made in many other countries.

Jan 1, 1939

By T Honeyands

At present we are witnessing large investments in the iron ore industry, fuelled by demand from Asia. At the same time, there is a changing landscape in pricing of iron ores, with the recent demise of the benchmark system and the evolution of market based index pricing systems. From a customer perspective, it is the behaviour of iron ores in downstream processing that gives them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions, and in setting quality price differentials.This paper describes the use of the Marx value in use (VIU) model to quantify the downstream value of iron ores. The Marx model consists of heat and mass balance modules for sintering, pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples given for the relative value of haematite, Marra Mamba, and channel iron deposit (CID) ores.

Jul 11, 2011

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1986

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010